Re: Can't get siproxd to work

Hi Jody,

this looks to me like the mask_host is not setup propery. I can't
see more from that short log snipplet. How do you have configure
the mask_host and masked_host? The masked_host MUST be the outbound
IP of siproxd (which I doubt in your case).

Regards,
/Thomas


On 27 Aug, Jody McIntyre wrote:
> Thanks for the reply.
> 
> On Thu, Aug 26, 2004 at 07:29:57PM +0200, Thomas Ries wrote:
> 
>> 1) You may want to put in the correct access control mask into the
>>    configuration:
>> 
>>    hosts_allow_sip = 205.233.128.0/24
>> 
>>    should *probably* be: 205.233.218.0/24  (218 instead of 128)
> 
> You're right.  I was actually looking at things this morning again and
> noticed that.
> 
>> 2) Why does phone 1000 send an INVITE to [email protected] ??
>>    1002 is supposed to be registered at the asterisk server, which
>>    then should be called as 1002-2oA/[email protected]
> 
> I'm just dialing "1002" on the phone, which apparently sends the wrong
> thing.  It does ring the phone though.
> 
>> 3) The phone 1000 must have the public side IP configured as domain
>>    part of it's SIP URI (can be seen in a sent INVITE request, e.g.
>>    at 13:03:27 of your debugfile).
>>    As "From" header it shows "sip:[email protected]", however this must
>>    contain the public (outbound) IP of siproxd "sip:user-2oA/[email protected]" -
>>    otherwise incoming calls will not work properly.
>>    On some phones you simply cannot configure the domain part independently
>>    from the registration server - if this the case you must use the 
>>    mask_host feature of siproxd to correct the header fields properly.
> 
> OK, the phone does actually offer this feature, but it's called "Bypass
> Firewall NAT" at the bottom of the "SIP Configuration" page.
> 
> Unfortunately the feature does not work as it should.  Instead, the
> From: address still ends up as sip:[email protected] and the Contact:
> becomes sip:user-2oA/[email protected]  Fortunately the mask_host feature does
> fix the problem.
> 
> I still can't connect back through siproxd.  I tried dial by URL:
> sip:1005-2oA/[email protected] from extension 1002 (the phone on the internal
> network is now extension 1005 not 1000).  siproxd does not recognize the
> URL and treats it as an attempted outgoing call, which of course does
> not work.  A log is attached.  Any suggestions?
> 
> Thanks,
> Jody
> 
> 
> 
>> 
>> 
>> Regards,
>> /Thomas
>> 
>> ######################################################################
>> 

-- 
GnuPG: pub  1024D/87BCDC94 2000-03-19 Thomas Ries <[email protected]>
-      Fingerprint = 13D1 19F5 77D0 4CEC 8D3F  A24E 09FC C18A 87BC DC94
-      Key via pgp.openpkg.org / http://www.ries.ch.vu/87BCDC94.pub
VoIP:  sip:17476691342-rne+wJe3e/u3Jhga2bR/9VaTQe2KTcn/@public.gmane.org

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.3 (GNU/Linux)

iD8DBQBBL5JSCfzBioe83JQRArK0AJ96lAZCaualbIlbSqTexNtt3OrYLACfTGgN
VfI9gdhWV9CYHE0w6vNWDtk=
=W3Ve
-----END PGP SIGNATURE-----