Re: Newbie help

Hi Brad,

I don't know the answer to the common.h problem but if I can remember 
back six months I think I had the same problem. I got around it by 
grabbing the bsd-airtools package from the openbsd.org ports/packages list.

http://www.openbsd.org/3.2_packages/i386/bsd-airtools-0.2.tgz-long.html

The tools in this are dated a month or two older than the current source 
but seems to work just fine and there's nothing missing as far as I can 
tell. This is a regular openbsd package so just download it and "pkg_add 
bsd-airtools-0.2.tgz".

Tye


Brad Martin wrote:
> Tye,
> 
> Thanks for your response.  I think I am almost there, but let me give
> you an update.  
> I am running OpenBSD 3.2 with a SMC2632W (I ended up finding the SMC
> card at MicroCenter as part of the SMC2602W product.  This is the PCI
> card that comes with the PCMCIA card attached.  SMC just so happens to
> use the SMC2632W for the PCMCIA card.
> As far as the software goes, I was able to compile and run prism2dump
> and a few others.  My problem is that when compiling dwepdump or
> dstumbler, I get the following error about not being able to locate a
> file:
> 
> % make
>  | gcc -Wall -I/usr/local/include -c main.c
>  | In file included from main.c:54:
>  | dstumbler.h:50: bat/common.h: No such file or directory
>  | *** Error code 1
> 
> What is supposed to create this common.h file?  I think I may have seen
> the answer but I do not know what a "port" is or what to do with a port.
> 
> I feel that I am very close to getting these tools working.  Any help
> with this compiling issue would be much appreciated.  Thank you so much
> for your help.
> 
> -Brad Martin
> [email protected]
> 
> 
> 
> 
> 
> -----Original Message-----
> From: Tye F Hammerle [mailto:[email protected]] 
> Sent: Sunday, April 27, 2003 8:17 AM
> To: [email protected]; BSD AirTools
> Subject: Re: [BAT] Newbie help
> 
> Which BSD do you have (Open, Free, NET, i)? I'm running OpenBSD 3.2 with
> 
> a Linksys WPC11 card. OpenBSD detected the WPC-11 on install. The 
> bsd-airtools package from the openbsd.org ports collection installed and
> 
> works. I have been able to compile and install dwepcrack separately. I 
> have been able to crack WEP keys with dwepdump/dwepcrack. I used the 
> info available on the dachb0den.com site. One thing I found that I would
> 
> like more documentation on is how to tell when you're getting duplicate 
> iv's and precisely what the numbers displayed by dwepcrack mean. 
> Equipment that does weak iv filtering makes it very hard or perhaps 
> impossible to collect enough iv's to collect enough iv's. I've spent a 
> full 7 days capturing iv's between cisco gear on a test network without 
> any luck.
> 
> In my testing I've found that Linksys, Cisco and Orinoco do weak iv 
> filtering. D-Link told me they do not do weak iv filtering. I've found 
> that Netgear does not do weak iv filtering, at least the MA401 pccard 
> and MA402 ap do not.
> 
> My test setup was a laptop running W2K(with Netgear MA401 pccard) with a
> 
> batch file copying a 65 mb ISO across an MA402 AP to a server on the 
> wired network in a loop. It took 24 hours for dwepdump to catch enough 
> weak iv's for dwepcrack to get the WEP key. dwepcrack took 30 seconds to
> 
> load the weak iv's and 3 seconds to crack the WEP key. I swapped the 
> MA401 for a Linksys WPC11 and repeated the test. With the WPC11 doing 
> weak iv filtering it took 48 hours of capturing weak iv's from the MA402
> 
> to get enough to crack the WEP key.
> 
> I've also gotten Kismet up and working.
> 
> Tye
> 
> 
> Brad Martin wrote:
> 
>>I am about to attempt the install of BSD air tools.  I was hoping some
> 
> 
>>of you could tell me some hardware/software success stories about your
> 
> 
>>installs.  Right now I have BSD 3.2 (for wnet) on a IBM Thinkpad 600E.
> 
> 
>>I am clueless about which PCMCIA Wireless Card to get.  I keep hearing
> 
> 
>>SMC 2632W but I can't seem to find it anywhere.  Any of you have any 
>>other suggestions?  Any help, docs, references on BSD, or BSD
> 
> AirTools, 
> 
>>would be much appreciated.  Thank you in advance.
>>
>> 
>>
>>-Brad Martin
>>
>>[email protected]
>>
>>
>>
> 
> ------------------------------------------------------------------------
> 
>>_______________________________________________
>>Bat mailing list
>>[email protected]
>>http://lists.dachb0den.com/mailman/listinfo/bat
> 
> 
> 
> 
> _______________________________________________
> Bat mailing list
> [email protected]
> http://lists.dachb0den.com/mailman/listinfo/bat