Re: [siteplan] BBQ pump and motor
Felix Kersting <[email protected]> Mon, 21 May 2007 06:56:17 -0700
| Newsgroups | gmane.org.clubs.gobiodiesel.mixmasters |
|---|---|
| Message-ID | <[email protected]> |
This is a multi-part message in MIME format. --===============1167542413== Content-Type: multipart/alternative; boundary="------------050809090608050408070905" This is a multi-part message in MIME format. --------------050809090608050408070905 Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit Greg - we haven't been using the BBQ because it takes on too much water and no one drains it (too difficult). *************BUT********************* it may be a good venue for filling barrels for the transfer to Jeff B now that the weather is getting better. Let's have a discussion about that. Also, I have the Grainger's part number for another flexible rotor pump like the good old oil pump we are using. I think it would be best to just buy another (sized for one of the 1/3 hp motors) and use it, since the gear pump requires too much HP w/cold oil. We have also discussed inserting the 120 gal WH between the tote and the processor for continuity of process to the processors. Right now my focus on will be on getting the dryer & a second wash tote plumbed to facilitate the wash process for the large quantities of fuel we are receiving. Felix Gregory Rohde wrote: > Guys - > I picked up the pump from the BBQ/tote along with the other 1/3 HP > motor and installed the good motor. I reinstalled/plumbed the pump > last wed. but due to time constraints, I was not able to test it. I > also did not know at this point what hoses were designated for WVO. I > will be on site this afternoon to drop off more oil and plan to build > a recirc. loop for the pump and test it out. > gregr > > ------------------------------------------------------------------------ > Take the Internet to Go: Yahoo!Go puts the Internet in your pocket: > <http://us.rd.yahoo.com/evt=48253/*http://mobile.yahoo.com/go?refer=1GNXIC> > mail, news, photos & more. > ------------------------------------------------------------------------ > > _______________________________________________ > siteplan mailing list > [email protected] > http://lists.gobiodiesel.org/mailman/listinfo/siteplan > --------------050809090608050408070905 Content-Type: text/html; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit <!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> <meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type"> </head> <body bgcolor="#ffffff" text="#000000"> Greg - we haven't been using the BBQ because it takes on too much water and no one drains it (too difficult).<br> <br> *************BUT********************* it may be a good venue for filling barrels for the transfer to Jeff B now that the weather is getting better. Let's have a discussion about that. <br> <br> Also, I have the Grainger's part number for another flexible rotor pump like the good old oil pump we are using. I think it would be best to just buy another (sized for one of the 1/3 hp motors) and use it, since the gear pump requires too much HP w/cold oil.<br> <br> We have also discussed inserting the 120 gal WH between the tote and the processor for continuity of process to the processors. <br> <br> Right now my focus on will be on getting the dryer & a second wash tote plumbed to facilitate the wash process for the large quantities of fuel we are receiving.<br> <br> Felix<br> <br> Gregory Rohde wrote: <blockquote cite="mid20070519181707.96087.qmail-E6ZrdFAFqFyvuULXzWHTWIglqE1Y4D90QQ4Iyu8u01E@public.gmane.org" type="cite">Guys -<br> I picked up the pump from the BBQ/tote along with the other 1/3 HP motor and installed the good motor. I reinstalled/plumbed the pump last wed. but due to time constraints, I was not able to test it. I also did not know at this point what hoses were designated for WVO. I will be on site this afternoon to drop off more oil and plan to build a recirc. loop for the pump and test it out.<br> gregr<br> <br> <p> </p> <hr size="1">Take the Internet to Go: Yahoo!Go puts the <a href="http://us.rd.yahoo.com/evt=48253/*http://mobile.yahoo.com/go?refer=1GNXIC">Internet in your pocket:</a> mail, news, photos & more. <pre wrap=""> <hr size="4" width="90%"> _______________________________________________ siteplan mailing list <a class="moz-txt-link-abbreviated" href="mailto:[email protected]">[email protected]</a> <a class="moz-txt-link-freetext" href="http://lists.gobiodiesel.org/mailman/listinfo/siteplan">http://lists.gobiodiesel.org/mailman/listinfo/siteplan</a> </pre> </blockquote> </body> </html> --------------050809090608050408070905-- --===============1167542413== Content-Type: text/plain; charset="us-ascii" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit Content-Disposition: inline _______________________________________________ mixmasters mailing list [email protected] http://lists.gobiodiesel.org/mailman/listinfo/mixmasters --===============1167542413==--