Re: card reader

The /sbin/fdisk -l /dev/sda worked with Fedora core 3, but RH-9 returns 
"Unable to read."  Sure hate the thought of upgrading, but it looks like 
it may be time.

Actually, Fedora is ahead of this.  When the usb card reader is plugged in, 
a new entry pops up in /etc/fstab called /media/usbdisk which can be 
mounted and used like a hard drive.
bruce

On Monday 13 June 2005 10:19, Thomas Wallis wrote:
> On Sat, 11 Jun 2005, bbales wrote:
> > I bought another card reader for my smart media (camera) cards.  Red
> > hat 9 recognizes it, but I can't mount it.  Tried /dev/sd[a-f][1-7] 
> > and get "not a valid block device"
> >
> > Several files seem to recognize the card reader and /var/log/messages
> > reacts to plugging and unplugging the usb cable.  /var/log/messages
> > sees it on sda which I take to mean indicate /dev/sda, but nothing
> > works.
> >
> > usb is many times faster than serial when it works.  Any suggestions
> > will be appreciated.
> > bruce
>
>  	Try fdisk -l /dev/sda to show the partition table.  Then you can
> see the right partition to mount.
>
>  				T W
>
> > less /proc/scsi/usb-storage-1/3
> >  Host scsi0: usb-storage
> >       Vendor: Alcor
> >      Product: Mass Storage Device
> > Serial Number: None
> >     Protocol: Transparent SCSI
> >    Transport: Bulk
> >         GUID: 058f93500000000000000000
> >     Attached: Yes
> >
> > less /proc/scsi/scsi
> > Attached devices:
> > Host: scsi0 Channel: 00 Id: 00 Lun: 00
> >  Vendor: Generic  Model: USB SMC Reader   Rev: 1.00
> >  Type:   Direct-Access                    ANSI SCSI revision: 02
> >
> > less /proc/bus/usb/devices
> > T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
> > D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
> > P:  Vendor=058f ProdID=9350 Rev= 1.00
> > S:  Manufacturer=Alcor
> > S:  Product=Mass Storage Device
> > C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
> > I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
> > Driver=usb-storage E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
> > E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
> >
> > tail -f /var/log/messages
> > Jun 11 15:13:43 betty kernel: hub.c: new USB device 00:03.0-1,
> > assigned address 3
> > Jun 11 15:13:46 betty /etc/hotplug/usb.agent: Setup usb-storage for
> > USB product 58f/9350/100
> > Jun 11 15:13:46 betty kernel: sda : READ CAPACITY failed.
> > Jun 11 15:13:46 betty kernel: sda : status = 1, message = 00, host =
> > 0, driver = 08
> > Jun 11 15:13:46 betty kernel: Info fld=0x0, Current sd00:00: sense key
> > Not Ready
> > Jun 11 15:13:46 betty kernel: sda : block size assumed to be 512
> > bytes, disk size 1GB.
> > Jun 11 15:13:46 betty kernel: sda: Write Protect is off
> > Jun 11 15:13:46 betty kernel:  sda: I/O error: dev 08:00, sector 0
> > Jun 11 15:13:46 betty kernel:  I/O error: dev 08:00, sector 0
> > Jun 11 15:13:46 betty kernel:  unable to read partition table
> > Jun 11 15:13:47 betty devlabel: devlabel service started/restarted
> >
> >
> > -- This is the [email protected] list.  To unsubscribe,
> > visit http://www.complete.org/cgi-bin/listargate-aclug.cgi
>
> Disclaimer: All opinions expressed here are my own and not those of WSU.
>
> EMAIL address:  wallis-1r0N/[email protected]
>
>
>
> -- This is the [email protected] list.  To unsubscribe,
> visit http://www.complete.org/cgi-bin/listargate-aclug.cgi


-- This is the [email protected] list.  To unsubscribe,
visit http://www.complete.org/cgi-bin/listargate-aclug.cgi