Re: big sur: info files for po4a and module-build-pm-11.3 and stuck with libxslt-1.1.34-1 failed

On Wed, 9 Jun 2021, Hanspeter Niederstrasser wrote:
> On 6/8/21 4:24 PM, Sven de Vries wrote:
>>>> tried to build under 11.4 package  po4a (actually emacs26 is the goal).
>>>> 
>>>> I needed to create po4a-11.3 and module-build-pm-11.3 see attached. Maybe 
>>>> someone could push them into the tree.??
>>> 
>>> Does extutils-parsexs-pm (a dependency for module-build-pm) pass tests for
>>> you on 11.3? That's what's been keeping me from adding module-build-pm to 
>>> 11.3.
>> 
>> strange enough, it seems to be installed :
>>   i   extutils-parsex  3.35-1       Converts Perl XS code into C code
>> 
>> but if I try to rebuild it (unsure of the name extutils-parsex-pm or 
>> extutils-parsex) in both cases it says: Failed: no package found for 
>> specification
>> 
>> The header of the infofile I find starts with:
>> 
>> Package: extutils-parsexs-pm
>> Version: 3.35
>> Revision: 1
>
> `fink list` only shows part of the package name if the terminal window is too 
> narrow. You can make the window wider to get the full name or run `fink list 
> -t extutils-parsexs` to get the full package name.

sorry, thanks, that shows:
i      extutils-parsexs-pm     3.35-1
p      extutils-parsexs-pm5302


>>> For the libxml/libxslt problem, that was fixed over the weekend (your 
>>> selfupdate must have just missed it).
>> 
>> strange enough, that is not the case neither ...
>> if I just try again to install po4a I get:
>> 
>> The following 4 additional packages will be installed:
>>   libxslt-bin libxslt-shlibs module-build-pm sgmls-pm
>> 
>> and then building libxslt  fails with:
>> checking for xml2-config... /opt/sw3/bin/xml2-config
>> checking for LIBXML... no
>> configure: error: Could not find libxml2 anywhere, check 
>> ftp://xmlsoft.org/.
>> ### execution of ./configure failed, exit code 1
>> ### execution of /tmp/fink.XX74q failed, exit code 1
>> 
>> the configure-invocation is:
>> ./configure --prefix=/opt/sw3   --without-crypto --disable-static 
>> --without-python --with-html-subdir=libxslt --enable-dependency-tracking 
>> --disable-silent-rules XSLTPROC=/usr/bin/true
>> 
>> 
>> and fink dumpinfo libxslt
>> 
>> tells me:
>> 
>> infofile: /opt/sw3/fink/dists/stable/main/finkinfo/libs/libxslt.info
>> debfile: 
>> /opt/sw3/fink/11.3/stable/main/binary-darwin-x86_64/libs/libxslt_1.1.34-2_darwin-x86_64.deb 
>> package: libxslt
>> epoch:
>> version: 1.1.34
>> revision: 2
>> family: libxslt, libxslt-shlibs, libxslt-bin
>> status: latest
>> allversions:
>>          1.1.34-2
>
> This is confusing (you have deb file but it still tries to build the 
> package). What does `fink list -t libxml2 libxslt` show?

omitting lines without "i":
i      libxml2 2.9.12-2        XML parsing library, version 2
i      libxml2-bin     2.9.12-2        XML parsing library, version 2
i      libxml2-shlibs  2.9.12-2        XML parsing library, version 2

but only not installed libxslts*

best
sven

_______________________________________________
Fink-users mailing list
[email protected]
List archive:
https://sourceforge.net/p/fink/mailman/fink-users/
Subscription management:
https://lists.sourceforge.net/lists/listinfo/fink-users