Re: RPI4 U-Boot 2020.10-rc5 please test xhci feature
Klaus Cucinauomo via freebsd-arm <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.arm |
|---|---|
| Message-ID | <[email protected]> |
> Am 05.10.2020 um 07:45 schrieb Klaus Cucinauomo <[email protected]>: > > ( https://wiki.freebsd.org/arm/Raspberry%20Pi#RPI4 ) > > new compiled U-Boot version U-Boot 2020.10-rc5 > > —- 1st try with default settings/files/configuratios ext. USB-SSD/ no SD-card present:— > > ………..U-Boot 2020.10-rc5 (Oct 05 2020 - 03:08:23 +0000) > > DRAM: 7.9 GiB > RPI 4 Model B (0xd03114) > MMC: mmc@7e300000: 1, emmc2@7e340000: 0 > Loading Environment from FAT... In: serial > Out: vidconsole > Err: vidconsole > Net: eth0: ethernet@7d580000 > PCIe BRCM: link up, 5.0 Gbps x1 (SSC) > starting USB... > Bus xhci_pci: probe failed, error -110 > No working controllers found………. > — > 2020.10-rc5 boots fine from SD-card > > happy testing > > thanks > Regards > Klaus > > The 4GB-model scans xhci correctly (although not detecting kernel/filesystem for now in early testing) (Same disk as on 8GB-test,no SD-card present, `ve changed some files in msdos-partition (start4.elf, config.txt,/overlays etc.)) while the 8GB model needs further patches because the VL805 - firmware is no more loaded by an own eeprom , so has to be loaded explicitly by the SoC's VideoCore. U-Boot 2020.10-rc5 (Oct 05 2020 - 03:08:23 +0000) DRAM: 3.1 GiB RPI 4 Model B (0xc03111) MMC: mmc@7e300000: 1, emmc2@7e340000: 0 Loading Environment from FAT... In: serial Out: serial Err: serial Net: eth0: ethernet@7d580000 PCIe BRCM: link up, 5.0 Gbps x1 (SSC) starting USB... Bus xhci_pci: Register 5000420 NbrPorts 5 Starting the controller USB XHCI 1.00 scanning bus xhci_pci for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Hit any key to stop autoboot: 0 Card did not respond to voltage select! Device 0: Vendor: JMicron Rev: 3202 Prod: Tech Type: Hard Disk Capacity: 114473.4 MB = 111.7 GB (234441648 x 512) ... is now current device Scanning usb 0:1... Found EFI removable media binary efi/boot/bootaa64.efi libfdt fdt_check_header(): FDT_ERR_BADMAGIC Scanning disk [email protected]... Disk [email protected] not ready Card did not respond to voltage select! Scanning disk [email protected]... Disk [email protected] not ready Scanning disk usb_mass_storage.lun0... ** Unrecognized filesystem type ** Found 3 disks No EFI system partition BootOrder not defined EFI boot manager: Cannot load any image 688192 bytes read in 5 ms (131.3 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC Booting /efi\boot\bootaa64.efi Consoles: EFI console Reading loader env vars from /efi/freebsd/loader.env Setting currdev to disk0p1: failed to allocate staging area: 9 failed to allocate staging area ## Application failed, r = 5 EFI LOAD FAILED: continuing... BOOTP broadcast 1 BOOTP broadcast 2 —————————————————————————————————————— Klaus _______________________________________________ [email protected] mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-arm To unsubscribe, send any mail to "[email protected]"