Re: RPi and powerd, was: Re: RPI4 clock speeds and serial port ( temperatures idle and -j4 buildworld buildkernel )

[Turns out I somehow ended up with /etc/rc.conf not edited
to enable powerd : that is what I found when I went back
to disable it. Now I get to re-run the tests.]

On 2021-Mar-25, at 10:23, Mark Millard <marklmi at yahoo.com> wrote:

> On 2021-Mar-24, at 14:13, Mark Millard <marklmi at yahoo.com> wrote:
> 
>> On 2021-Mar-23, at 16:15, Mark Millard <marklmi at yahoo.com> wrote:
>> 
>>> On 2021-Mar-23, at 12:57, Mark Millard <marklmi at yahoo.com> wrote:
>>>> 
>>>> 
>>>> On 2021-Mar-23, at 06:56, tech-lists <tech-lists at zyxst.net> wrote:
>>>> 
>>>>> Hi,
>>>>> 
>>>>> latest build run:
>>>> 
>>>> Had a -mcpu=cortext-a72 world and kernel been
>>>> installed and booted first? Was the system
>>>> running a world and kernel that had not been
>>>> tuned for the Cortex-A72?
>>> 
>>> I've started an experimental build in my
>>> -mcpu=cortex-a72 tuned context . . .
>>> 
>>>>>>>> World built in 22976 seconds, ncpu: 4, make -j6
>>>>> --------------------------------------------------------------
>>>>> 
>>>>> 6 Hours : 22 Minutes : 56 Seconds
>>>>> 
>>>>> created kernel.bin from kernel.full
>>>>> --------------------------------------------------------------
>>>>>>>> Kernel build for GENERIC-NODEBUG completed on Mon Mar 22 13:54:53
>>>>>>>> UTC 2021
>>>>> --------------------------------------------------------------
>>>>>>>> Kernel(s)  GENERIC-NODEBUG built in 2086 seconds, ncpu: 4, make -j6
>>>>> --------------------------------------------------------------
>>>>> 
>>>>> 0 Hours : 34 Minutes : 46 Seconds
>>>>> 
>>>>> commands used:
>>>>> 1. cd /usr/src
>>>>> 2. git pull --ff-only
>>> 
>>> I'm simply from-scratch rebuilding what I'm
>>> already running, based on main 7381bbee29df from
>>> 2021-03-12:
>>> 
>>> # ~/fbsd-based-on-what-freebsd-main.sh 
>>> merge-base: 7381bbee29df959e88ec59866cf2878263e7f3b2
>>> merge-base: CommitDate: 2021-03-12 20:29:42 +0000
>>> def0058cc690 (HEAD -> mm-src) mm-src snapshot for mm's patched build in git context.
>>> 7381bbee29df (freebsd/main, freebsd/HEAD, pure-src, main) cam: Run all XPT_ASYNC ccbs in a dedicated thread
>>> FreeBSD RPi4B 14.0-CURRENT FreeBSD 14.0-CURRENT mm-src-n245445-def0058cc690 GENERIC-NODBG  arm64 aarch64 1400005 1400005
>>> 
>>>>> 3. make -j10 cleanworld
>>>>> 4. make -j10 cleandir
>>>>> 5. make -j10 clean
>>> 
>>> My /usr/obj/cortexA72_clang/ was empty at the
>>> start of the buildworld buildkernel .
>>> devel/ccache is still not installed.
>>> 
>>>> This does not show ccache being cleared out
>>>> before the below. So the times may be examples
>>>> of "with ccache benefit" times. The contrast
>>>> with mine and Bob P.'s times suggests a
>>>> nice time-benefit can occur.
>>>> 
>>>>> 6. make -j6 buildworld
>>>>> 7. make -j6 buildkernel
>>> 
>>> I'm using "-j6 buildworld buildkernel".
>>> 
>>>>> here's the src.conf :
>>>>> https://cloud.zyxst.net/~john/FreeBSD/rpi4-main/src.conf
>>> 
>>> I'm using my normal src.conf equivalent, not
>>> yours. (So the experiment is comparable to my
>>> normal past experiments in this respect, matching
>>> what I've reported in the past.)
>>> 
>>>> I seem to get intermittent access to
>>>> https://cloud.zyxst.net/ but got to
>>>> see the file content eventually.
>>>> 
>>>>> relevant rc.conf settings:
>>>>> powerd_enable="YES"
>>>>> powerd_flags="-r 1"
>>> 
>>> I commented out the config.txt line that assigned
>>> arm_freq_min and the /etc/sysctl/conf line that
>>> assigned an arm frequency.

I get to retry, attempting to actually do what I said
I'd done for powerd enabling . . . I've rebooted and
verified powerd now shows with the appropriate command
line in top. So I've cleared things out in
/usr/obj/cortexA72_clang/ and started a -j6 experiment
as the first one.

>>> I put the 2 powerd_* lines above in my /etc/rc.conf .
>>> 
>>>>> sysctl.conf settings:
>>>>> vfs.read_max=128 # default 64 # Cluster read-ahead max block count
>>> 
>>> I added the above line to my /etc/sysctl.conf .
>>> 
>>>>> config.txt:
>>>>> kernel=u-boot.bin
>>>>> over_voltage=6
>>>>> arm_freq=2000
>>>>> sdram_freq_min=3200
>>> 
>>> Ignoring comment differences, mine matches
>>> for such lines.
>>> 
>>> I rebooted on the basis of all these changes
>>> before starting the "-j6 buildworld buildkernel"
>>> style build.
>>> 
>>>> Thanks much for the information.
>>>> 
>>> 
>>> So, 6..10(?) of hours from when the
>>> build started I should have time frames
>>> to report for a "no ccache benefit"
>>> build to compare to my past reported
>>> build times.
>>> 
>> 
>> Summary: Overall somewhat under 9 hrs historically
>> turned into somewhat under 15 hrs 35 min, adding
>> somewhat over 6.5 hours to the time. Not a
>> configuration that I'm likely to generally use.
>> 
>> The details:
>> 
>> First a reminder of the prior timing that I
>> reported for my normal configuration of my
>> normal -j4 buildworld buildkernel in my
>> usual overclocking style:
>> 
>> World build completed on Thu Mar 11 18:39:37 PST 2021
>> World built in 29780 seconds, ncpu: 4, make -j4
>> Kernel build for GENERIC-NODBG completed on Thu Mar 11 19:18:02 PST 2021
>> Kernel(s)  GENERIC-NODBG built in 2305 seconds, ncpu: 4, make -j4
>> 
>> So a few minutes under 9 hr total for my
>> normal configuration.
>> 
>> By contrast, for the configuration in this
>> experiment:

Context description correction:
The below was for using neither powerd nor forcing
the arm clock rate: left as u-boot set it. (But
the RAM clock rate was still forced).

>> World build completed on Wed Mar 24 06:10:39 PDT 2021
>> World built in 52030 seconds, ncpu: 4, make -j6
>> Kernel build for GENERIC-NODBG completed on Wed Mar 24 07:16:50 PDT 2021
>> Kernel(s)  GENERIC-NODBG built in 3971 seconds, ncpu: 4, make -j6
>> 
>> 
>> Notes on some of what may be going on here:
>> 
>> Given the RPi4's memory subsystem and its RAM caching,
>> my first guess is that the -j6 (instead of -j4) leads
>> to the RAM caching being far less effective and so RAM
>> access looks far slower overall, with more waiting for
>> other threads memory activity (memory bus contention).
>> 
>> In some past experiments, I've seen configurations
>> where -j3 did buildworld buildkernel faster than
>> -j4 : before I started setting the RAM clock rate
>> minimum as well. So this "-jM < -jN" is faster for
>> the smaller M is not a new type of potential
>> conclusion and -j4 (or -j3) vs. -j6 may be another
>> example.
>> 
>> I've also done a type of benchmarking that saturates
>> what the RPi4 can do --with fewer than 4 cores
>> involved in order to reach saturation in the
>> benchmark.
>> 
>> (Benchmark on a scale-of-problem and RAM access
>> pattern that makes the RAM caching fairly ineffective.
>> A MACCHIATObin Double Shot also has 4 Cortex-A72
>> cores and does not have this property for the
>> benchmark: different RAM caching. Even runninf the
>> RPi4B and MACCHIATObin Double Shot at the same
>> arm CPU speed, the MACCHIATObin Double Shot takes
>> less time for the same work.)
>> 
>> So I might retry the build with, say, -j4 but the
>> rest being the same (after clearing out the existing
>> build). That would likely hint at if the hypothesis
>> has a chance of being correct vs. incorrect.
>> 
> 
> Turns out that the -j4 buildworld timing almost
> exactly matches -j6 for the type of context:
> buildworld took about 81 sec longer (out of
> somewhat more than 52000 sec). (The 8 GB RPi4B's
> have sufficient RAM to not run out during -j6 .
> 4GB ones might as well. 2GB ones likely would
> runout [swap/page activity].)
> 
> As similar point goes for buildkernel: around
> 33 sec longer (out of somewhat less than 4000
> seconds).

Context description correction:
The below was for using neither powerd nor forcing
the arm clock rate: left as u-boot set it. (But
the RAM clock rate was still forced).

> World build completed on Thu Mar 25 04:43:53 PDT 2021
> World built in 52111 seconds, ncpu: 4, make -j4
> Kernel build for GENERIC-NODBG completed on Thu Mar 25 05:50:38 PDT 2021
> Kernel(s)  GENERIC-NODBG built in 4004 seconds, ncpu: 4, make -j4
> 
> So using -j6 was not an notable improvement over
> using -j4 for the type of context but also was not
> a significant harm either (sufficient RAM present
> to avoid consequences of that type).
> 



===
Mark Millard
marklmi at yahoo.com
( dsl-only.net went
away in early 2018-Mar)

_______________________________________________
[email protected] mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-arm
To unsubscribe, send any mail to "[email protected]"