Re: Can't enable SDIO wifi module on PBP
Ronald Klop <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.arm,gmane.os.freebsd.devel.wireless |
|---|---|
| Message-ID | <1899735108.281.1622818169330@localhost> |
Hi, People with more knowledge about this should anwer instead of me. But as far as I know there is no driver for this WiFi module on FreeBSD. Regards, Ronald. Van: KIRIYAMA Kazuhiko <[email protected]> Datum: vrijdag, 4 juni 2021 13:19 Aan: [email protected] CC: [email protected] Onderwerp: Re: Can't enable SDIO wifi module on PBP > > On Fri, 04 Jun 2021 20:07:38 +0900, > KIRIYAMA Kazuhiko wrote: > > > > Hi, all > > > > I've reconfigured kernel to GENERIC-MMCCAM on Pinebook Pro (PBP) to use SDIO > > wifi module Broadcom BCM43456 (AMPAK AP6256 [1]). But nothing SDIO module > > Sorry for not adding reference sites. Broadcom BCM43456 on AMPAK AP6256 > sites to [1] and FreeBSD SDIO reference site is [2]. > > [1] https://wiki.pine64.org/wiki/Pinebook_Pro#Hardware_Overview > [2] https://wiki.freebsd.org/SDIO > > > found : > > > > root@kazu:~ # camcontrol devlist -v > > scbus0 on dw_mmc_sim0 bus 0: > > scbus1 on dw_mmc_sim1 bus 0: > > scbus2 on sdhci_slot0 bus 0: > > <MMCHC DA4128 0.1 SN AD0EFC3E MFG 03/200> at scbus2 target 0 lun 0 (pass0,sdda0) > > scbus-1 on xpt0 bus 0: > > <> at scbus-1 target -1 lun ffffffff (xpt0) > > root@kazu:~ # > > > > My environments are as follows : > > > > root@kazu:~ # uname -a > > FreeBSD kazu.tfc 14.0-CURRENT FreeBSD 14.0-CURRENT #0 n246349-daa5350d0e0c: Wed Jun 2 17:01:11 JST 2021 root@tbedfc:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC-MMCCAM arm64 > > root@kazu:~ # cat /var/run/dmesg.boot > > ---<<BOOT>>--- > > GDB: debug ports: uart > > GDB: current port: uart > > KDB: debugger backends: ddb gdb > > KDB: current backend: ddb > > WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance > > Copyright (c) 1992-2021 The FreeBSD Project. > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > > The Regents of the University of California. All rights reserved. > > FreeBSD is a registered trademark of The FreeBSD Foundation. > > FreeBSD 14.0-CURRENT #0 n246349-daa5350d0e0c: Wed Jun 2 17:01:11 JST 2021 > > root@tbedfc:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC-MMCCAM arm64 > > FreeBSD clang version 11.0.1 ([email protected]:llvm/llvm-project.git llvmorg-11.0.1-0-g43ff75f2c3fe) > > WARNING: WITNESS option enabled, expect reduced performance. > > VT(efifb): resolution 1920x1080 > > module firmware already present! > > real memory = 4158373888 (3965 MB) > > avail memory = 4025626624 (3839 MB) > > Starting CPU 1 (1) > > Starting CPU 2 (2) > > Starting CPU 3 (3) > > Starting CPU 4 (100) > > Starting CPU 5 (101) > > FreeBSD/SMP: Multiprocessor System Detected: 6 CPUs > > random: unblocking device. > > random: entropy device external interface > > MAP f3f16000 mode 2 pages 4 > > MAP f3f1b000 mode 2 pages 4 > > MAP f6f40000 mode 2 pages 16 > > WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 14.0. > > kbd0 at kbdmux0 > > WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 14.0. > > ofwbus0: <Open Firmware Device Tree> > > clk_fixed0: <Fixed clock> on ofwbus0 > > simplebus0: <Flattened device tree simple bus> on ofwbus0 > > rk_grf0: <RockChip General Register Files> mem 0xff320000-0xff320fff on ofwbus0 > > rk3399_pmucru0: <Rockchip RK3399 PMU Clock and Reset Unit> mem 0xff750000-0xff750fff on ofwbus0 > > rk3399_cru0: <Rockchip RK3399 Clock and Reset Unit> mem 0xff760000-0xff760fff on ofwbus0 > > rk_grf1: <RockChip General Register Files> mem 0xff770000-0xff77ffff on ofwbus0 > > regfix0: <Fixed Regulator> on ofwbus0 > > regfix1: <Fixed Regulator> on ofwbus0 > > regfix2: <Fixed Regulator> on ofwbus0 > > regfix3: <Fixed Regulator> on ofwbus0 > > regfix4: <Fixed Regulator> on ofwbus0 > > regfix5: <Fixed Regulator> on ofwbus0 > > regfix6: <Fixed Regulator> on ofwbus0 > > regfix7: <Fixed Regulator> on ofwbus0 > > regfix8: <Fixed Regulator> on ofwbus0 > > regfix9: <Fixed Regulator> on ofwbus0 > > regfix10: <Fixed Regulator> on ofwbus0 > > regfix11: <Fixed Regulator> on ofwbus0 > > simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0xff310000-0xff310fff on ofwbus0 > > psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 > > gic0: <ARM Generic Interrupt Controller v3.0> mem 0xfee00000-0xfee0ffff,0xfef00000-0xfefbffff,0xfff00000-0xfff0ffff,0xfff10000-0xfff1ffff,0xfff20000-0xfff2ffff irq 18 on ofwbus0 > > its0: <ARM GIC Interrupt Translation Service> mem 0xfee20000-0xfee3ffff on gic0 > > rk_iodomain0: <RockChip IO Voltage Domain> mem 0-0xff31ffff,0-0xfff on rk_grf0 > > rk_iodomain1: <RockChip IO Voltage Domain> mem 0-0xff76ffff,0-0xffff on rk_grf1 > > rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0 > > gpio0: <RockChip GPIO Bank controller> mem 0xff720000-0xff7200ff irq 71 on rk_pinctrl0 > > gpiobus0: <OFW GPIO bus> on gpio0 > > gpio1: <RockChip GPIO Bank controller> mem 0xff730000-0xff7300ff irq 72 on rk_pinctrl0 > > gpiobus1: <OFW GPIO bus> on gpio1 > > gpio2: <RockChip GPIO Bank controller> mem 0xff780000-0xff7800ff irq 73 on rk_pinctrl0 > > gpiobus2: <OFW GPIO bus> on gpio2 > > gpio3: <RockChip GPIO Bank controller> mem 0xff788000-0xff7880ff irq 74 on rk_pinctrl0 > > gpiobus3: <OFW GPIO bus> on gpio3 > > gpio4: <RockChip GPIO Bank controller> mem 0xff790000-0xff7900ff irq 75 on rk_pinctrl0 > > gpiobus4: <OFW GPIO bus> on gpio4 > > rk_i2c0: <RockChip I2C> mem 0xff110000-0xff110fff irq 20 on ofwbus0 > > iicbus0: <OFW I2C bus> on rk_i2c0 > > rk_i2c1: <RockChip I2C> mem 0xff130000-0xff130fff irq 22 on ofwbus0 > > iicbus1: <OFW I2C bus> on rk_i2c1 > > rk_i2c2: <RockChip I2C> mem 0xff3c0000-0xff3c0fff irq 38 on ofwbus0 > > iicbus2: <OFW I2C bus> on rk_i2c2 > > syr8270: <Silergy SYR827 regulator> at addr 0x80 on iicbus2 > > rk_i2c3: <RockChip I2C> mem 0xff3d0000-0xff3d0fff irq 39 on ofwbus0 > > iicbus3: <OFW I2C bus> on rk_i2c3 > > rk805_pmu0: <RockChip RK805 PMIC> at addr 0x36 irq 76 on iicbus2 > > generic_timer0: <ARMv8 Generic Timer> irq 2,3,4,5 on ofwbus0 > > Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000 > > Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000 > > rk_tsadc0: <RockChip temperature sensors> mem 0xff260000-0xff2600ff irq 35 on ofwbus0 > > rk_usb2phy0: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1 > > rk_usb2phy1: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1 > > rk_emmcphy0: <Rockchip RK3399 eMMC PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1 > > rk_pcie_phy0: <Rockchip RK3399 PCIe PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1 > > rk_typec_phy0: <Rockchip RK3399 PHY TYPEC> mem 0xff7c0000-0xff7fffff on ofwbus0 > > rk_typec_phy1: <Rockchip RK3399 PHY TYPEC> mem 0xff800000-0xff83ffff on ofwbus0 > > cpulist0: <Open Firmware CPU Group> on ofwbus0 > > cpu0: <Open Firmware CPU> on cpulist0 > > cpufreq_dt0: <Generic cpufreq driver> on cpu0 > > cpu1: <Open Firmware CPU> on cpulist0 > > cpufreq_dt1: <Generic cpufreq driver> on cpu1 > > cpu2: <Open Firmware CPU> on cpulist0 > > cpufreq_dt2: <Generic cpufreq driver> on cpu2 > > cpu3: <Open Firmware CPU> on cpulist0 > > cpufreq_dt3: <Generic cpufreq driver> on cpu3 > > cpu4: <Open Firmware CPU> on cpulist0 > > cpufreq_dt4: <Generic cpufreq driver> on cpu4 > > cpu5: <Open Firmware CPU> on cpulist0 > > cpufreq_dt5: <Generic cpufreq driver> on cpu5 > > pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0 > > pmu1: <Performance Monitoring Unit> irq 1 on ofwbus0 > > pcib0: <Rockchip PCIe controller> mem 0xf8000000-0xf9ffffff,0xfd000000-0xfdffffff irq 6,7,8 on ofwbus0 > > pcib0: Gen1 link training timeouted: 0x00080001. > > pci0: <PCI bus> on pcib0 > > pcib1: <PCI-PCI bridge> at device 0.0 on pci0 > > pcib0: failed to reserve resource for pcib1 > > pcib1: failed to allocate initial memory window: 0-0xfffff > > pci1: <PCI bus> on pcib1 > > rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe310000-0xfe313fff irq 10 on ofwbus0 > > rockchip_dwmmc0: Hardware version ID is 270a > > rockchip_dwmmc1: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe320000-0xfe323fff irq 11 on ofwbus0 > > rockchip_dwmmc1: Hardware version ID is 270a > > sdhci_fdt0: <Rockchip RK3399 fdt SDHCI controller> mem 0xfe330000-0xfe33ffff irq 12 on ofwbus0 > > rk_emmcphy0: got emmcclk clock > > sdhci_fdt0-slot0: Hardware doesn't specify timeout clock frequency, setting BROKEN_TIMEOUT quirk. > > sdhci_fdt0: 1 slot(s) allocated > > uma_zalloc_debug: zone "malloc-2048" with the following non-sleepable locks held: > > exclusive sleep mutex SD slot mtx (sdhci) r = 0 (0xffff0000411c6030) locked @ /usr/src/sys/dev/sdhci/sdhci.c:617 > > stack backtrace: > > #0 0xffff0000004d819c at witness_debugger+0x64 > > #1 0xffff0000004d9320 at witness_warn+0x3e8 > > #2 0xffff0000006f9084 at uma_zalloc_debug+0x2c > > #3 0xffff0000006f8a8c at uma_zalloc_arg+0x2c > > #4 0xffff00000043fa18 at malloc+0xa0 > > #5 0xffff00000000f550 at xpt_alloc_ccb+0x1c > > #6 0xffff000000034ee0 at mmccam_start_discovery+0x18 > > #7 0xffff0000002506fc at sdhci_card_task+0x110 > > #8 0xffff000000255460 at sdhci_fdt_attach+0x5b4 > > #9 0xffff0000004a3b34 at device_attach+0x400 > > #10 0xffff0000004a369c at device_probe_and_attach+0x7c > > #11 0xffff0000004a5880 at bus_generic_new_pass+0xf8 > > #12 0xffff0000004a5830 at bus_generic_new_pass+0xa8 > > #13 0xffff0000004a5830 at bus_generic_new_pass+0xa8 > > #14 0xffff0000004a0ae0 at bus_set_pass+0x4c > > #15 0xffff0000003f644c at mi_startup+0x12c > > #16 0xffff0000000008a8 at virtdone+0x6c > > ehci0: <Generic EHCI Controller> mem 0xfe380000-0xfe39ffff irq 13 on ofwbus0 > > usbus0: EHCI version 1.0 > > usbus0 on ehci0 > > ohci0: <Generic OHCI Controller> mem 0xfe3a0000-0xfe3bffff irq 14 on ofwbus0 > > usbus1 on ohci0 > > ehci1: <Generic EHCI Controller> mem 0xfe3c0000-0xfe3dffff irq 15 on ofwbus0 > > usbus2: EHCI version 1.0 > > usbus2 on ehci1 > > ohci1: <Generic OHCI Controller> mem 0xfe3e0000-0xfe3fffff irq 16 on ofwbus0 > > usbus3 on ohci1 > > rk_dwc30: <Rockchip RK3399 DWC3> on ofwbus0 > > xhci0: <Synopsys Designware DWC3> mem 0xfe800000-0xfe8fffff irq 77 on rk_dwc30 > > xhci0: 64 bytes context size, 32-bit DMA > > usbus4: trying to attach > > usbus4 on xhci0 > > rk_dwc31: <Rockchip RK3399 DWC3> on ofwbus0 > > xhci1: <Synopsys Designware DWC3> mem 0xfe900000-0xfe9fffff irq 78 on rk_dwc31 > > xhci1: 64 bytes context size, 32-bit DMA > > usbus5: trying to attach > > usbus5 on xhci1 > > iicbus0: <unknown card> at addr 0x22 > > iic0: <I2C generic I/O> on iicbus0 > > iic1: <I2C generic I/O> on iicbus1 > > uart0: <Non-standard ns8250 class UART with FIFOs> mem 0xff180000-0xff1800ff irq 26 on ofwbus0 > > uart0: debug port (-1,n,8,1) > > uart1: <16750 or compatible> mem 0xff1a0000-0xff1a00ff irq 28 on ofwbus0 > > uart1: console (1500000,n,8,1) > > spi0: <Rockchip SPI> mem 0xff1d0000-0xff1d0fff irq 31 on ofwbus0 > > spibus0: <OFW SPI bus> on spi0 > > spibus0: <unknown card> at cs 0 mode 0 > > iicbus2: <unknown card> at addr 0x82 > > iic2: <I2C generic I/O> on iicbus2 > > iicbus3: <unknown card> at addr 0x44 > > iic3: <I2C generic I/O> on iicbus3 > > pwm0: <Rockchip PWM> mem 0xff420000-0xff42000f on ofwbus0 > > pwmbus0: <OFW PWM bus> on pwm0 > > pwmc0: <PWM Control> channel 0 on pwmbus0 > > pwm1: <Rockchip PWM> mem 0xff420020-0xff42002f on ofwbus0 > > pwmbus1: <OFW PWM bus> on pwm1 > > pwmc1: <PWM Control> channel 0 on pwmbus1 > > gpioc0: <GPIO controller> on gpio0 > > gpioc1: <GPIO controller> on gpio1 > > gpioc2: <GPIO controller> on gpio2 > > gpioc3: <GPIO controller> on gpio3 > > gpioc4: <GPIO controller> on gpio4 > > gpioled0: <GPIO LEDs> on ofwbus0 > > armv8crypto0: <AES-CBC,AES-XTS,AES-GCM> > > Timecounters tick every 1.000 msec > > usbus0: 480Mbps High Speed USB v2.0 > > usbus1: 12Mbps Full Speed USB v1.0 > > rk805_pmu0: registered as a time-of-day clock, resolution 1.000000s > > Release APs...done > > usbus2: 480Mbps High Speed USB v2.0 > > CPU 0: ARM Cortex-A53 r0p4 affinity: 0 0 > > usbus3: 12Mbps Full Speed USB v1.0 > > Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> > > usbus4: 5.0Gbps Super Speed USB v3.0 > > Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL> > > usbus5: 5.0Gbps Super Speed USB v3.0 > > Instruction Set Attributes 1 = <> > > (noperiph:dw_mmc_sim0:0:-1:ffffffff): Processor Features 0 = <GIC,AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32> > > Processor Features 1 = <> > > Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> > > Memory Model Features 1 = <8bit VMID> > > Memory Model Features 2 = <32bit CCIDX,48bit VA> > > Debug Features 0 = <2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8> > > Debug Features 1 = <> > > Auxiliary Features 0 = <> > > Auxiliary Features 1 = <> > > CPU 1: ARM Cortex-A53 r0p4 affinity: 0 1 > > Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> > > Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> > > CPU 2: ARM Cortex-A53 r0p4 affinity: 0 2 > > Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> > > Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> > > CPU 3: ARM Cortex-A53 r0p4 affinity: 0 3 > > Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> > > Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> > > CPU 4: ARM Cortex-A72 r0p2 affinity: 1 0 > > Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG> > > Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA> > > CPU 5: ARM Cortex-A72 r0p2 affinity: 1 1 > > Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG> > > Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA> > > XPT_SCAN_{BUS,TGT,LUN} > > (noperiph:dw_mmc_sim0:0:0:0): XPT_SCAN_{BUS,TGT,LUN} > > (noperiph:dw_mmc_sim0:0:0:0): ugen4.1: <Synopsys XHCI root HUB> at usbus4 > > Set up the mmcprobe device... > > ugen0.1: <Generic EHCI root HUB> at usbus0 > > (mmcprobe0:dw_mmc_sim0:0:0:0): ugen3.1: <Generic OHCI root HUB> at usbus3 > > Periph created > > ugen1.1: <Generic OHCI root HUB> at usbus1 > > ugen5.1: <Synopsys XHCI root HUB> at usbus5 > > ugen2.1: <Generic EHCI root HUB> at usbus2 > > (mmcprobe0:dw_mmc_sim0:0:0:0): sysctl_warn_reuse: can't re-use a leaf (dev.uhub.%parent)! > > sysctl_warn_reuse: can't re-use a leaf (dev.uhub.%parent)! > > sysctl_warn_reuse: can't re-use a leaf (dev.uhub.%parent)! > > sysctl_warn_reuse: can't re-use a leaf (dev.uhub.%parent)! > > sysctl_warn_reuse: can't re-use a leaf (dev.uhub.%parent)! > > uhub1 on usbus0 > > uhub5 on usbus2 > > uhub1: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > > uhub5: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2 > > uhub4Probe started > > on usbus5 > > (mmcprobe0:dw_mmc_sim0:0:0:0): uhub2Probe PROBE_INVALID to PROBE_RESET > > on usbus3 > > (mmcprobe0:dw_mmc_sim0:0:0:0): uhub3mmcprobe_start > > on usbus1 > > uhub2: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 > > (mmcprobe0:dw_mmc_sim0:0:0:0): uhub4: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus5 > > Trying to mount root from ufs:/dev/mmcsd0p3 [rw]... > > Start with PROBE_RESET > > uhub3: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 > > (mmcprobe0:dw_mmc_sim0:0:0:0): Root mount waiting for:uhub0Start with PROBE_IDENTIFY > > CAM usbus0 usbus1 on usbus4 > > usbus2uhub0: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus4 > > usbus3 usbus4 usbus5 > > WARNING: WITNESS option enabled, expect reduced performance. > > Unresolved linked clock found: clkin_gmac > > lock order reversal: (sleepable after non-sleepable) > > 1st 0xffffa00001026558 dwmmcsim (dwmmcsim, sleep mutex) @ /usr/src/sys/cam/cam_xpt.c:2802 > > 2nd 0xffff000000c12a30 Clock topology lock (Clock topology lock, sx) @ /usr/src/sys/dev/extres/clk/clk.c:1154 > > lock order dwmmcsim -> Clock topology lock attempted at: > > #0 0xffff0000004d7e7c at witness_checkorder+0xc50 > > #1 0xffff0000004743e8 at _sx_xlock+0x7c > > #2 0xffff0000001ac808 at clk_set_freq+0x4c > > #3 0xffff00000078a998 at dwmmc_rockchip_update_ios+0x3c > > #4 0xffff00000078a3bc at dwmmc_update_ios+0xfc > > #5 0xffff000000789854 at dwmmc_cam_action+0x14c > > #6 0xffff000000009c34 at xpt_action_default+0xca8 > > #7 0xffff000000008f5c at xpt_action+0x270 > > #8 0xffff00000003633c at mmcprobe_start+0x89c > > #9 0xffff00000000cc10 at xpt_run_allocq+0x104 > > #10 0xffff00000000cadc at xpt_schedule+0x230 > > #11 0xffff000000035a78 at mmcprobe_register+0x2a4 > > #12 0xffff000000003b90 at cam_periph_alloc+0x528 > > #13 0xffff0000000354dc at mmc_action+0x484 > > #14 0xffff000000008f5c at xpt_action+0x270 > > #15 0xffff000000011750 at xpt_scanner_thread+0xcc > > #16 0xffff000000424198 at fork_exit+0x74 > > #17 0xffff00000076716c at fork_trampoline+0x14 > > uhub3: 1 port with 1 removable, self powered > > (mmcprobe0:dw_mmc_sim0:0:0:0): uhub2: 1 port with 1 removable, self powered > > Send first XPT_MMC_IO > > (noperiph:dw_mmc_sim1:0:-1:ffffffff): XPT_SCAN_{BUS,TGT,LUN} > > (noperiph:dw_mmc_sim1:0:0:0): (mmcprobe0:dw_mmc_sim0:0:0:0): XPT_SCAN_{BUS,TGT,LUN} > > done with PROBE_RESET > > (noperiph:dw_mmc_sim1:0:0:0): (mmcprobe0:dw_mmc_sim0:0:0:0): Set up the mmcprobe device... > > Probe PROBE_RESET to PROBE_SEND_IF_COND > > (mmcprobe1:dw_mmc_sim1:0:0:0): (mmcprobe0:dw_mmc_sim0:0:0:0): Periph created > > mmcprobe_done: remaining freeze count 0 > > (mmcprobe1:dw_mmc_sim1:0:0:0): (mmcprobe0:dw_mmc_sim0:0:0:0): Probe started > > mmcprobe_start > > (mmcprobe0:dw_mmc_sim0:0:0:0): (mmcprobe1:dw_mmc_sim1:0:0:0): Start with PROBE_SEND_IF_COND > > Probe PROBE_INVALID to PROBE_RESET > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_start > > (mmcprobe1:dw_mmc_sim1:0:0:0): Start with PROBE_RESET > > (mmcprobe0:dw_mmc_sim0:0:0:0): (mmcprobe1:dw_mmc_sim1:0:0:0): IF_COND: error 1, pattern 00000000 > > Start with PROBE_IDENTIFY > > (mmcprobe0:dw_mmc_sim0:0:0:0): Probe PROBE_SEND_IF_COND to PROBE_SDIO_RESET > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_start > > (mmcprobe0:dw_mmc_sim0:0:0:0): Start with PROBE_SDIO_RESET > > (mmcprobe0:dw_mmc_sim0:0:0:0): SDIO_RESET: error 1, CCCR CTL register: 00000000 > > (mmcprobe0:dw_mmc_sim0:0:0:0): Probe PROBE_SDIO_RESET to PROBE_SDIO_INIT > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_start > > (mmcprobe0:dw_mmc_sim0:0:0:0): Start with PROBE_SDIO_INIT > > (mmcprobe0:dw_mmc_sim0:0:0:0): SDIO_INIT: error 1, 00000000 00000000 00000000 00000000 > > (mmcprobe0:dw_mmc_sim0:0:0:0): Probe PROBE_SDIO_INIT to PROBE_SEND_APP_OP_COND > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_start > > (mmcprobe0:dw_mmc_sim0:0:0:0): APP_OP_COND: error 1, resp 00000000 > > (mmcprobe0:dw_mmc_sim0:0:0:0): Probe PROBE_SEND_APP_OP_COND to PROBE_MMC_INIT > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_start > > (mmcprobe0:dw_mmc_sim0:0:0:0): Start with PROBE_MMC_INIT > > (mmcprobe0:dw_mmc_sim0:0:0:0): MMC_INIT: error 1, resp 00000000 > > (mmcprobe0:dw_mmc_sim0:0:0:0): Probe PROBE_MMC_INIT to PROBE_INVALID > > (mmcprobe0:dw_mmc_sim0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:dw_mmc_sim0:0:0:0): Periph invalidated > > (mmcprobe0:dw_mmc_sim0:0:0:0): Periph destroyed > > uhub0: 2 ports with 2 removable, self powered > > uhub4: 2 ports with 2 removable, self powered > > (mmcprobe1:dw_mmc_sim1:0:0:0): Send first XPT_MMC_IO > > (noperiph:sdhci_slot0:0:-1:ffffffff): XPT_SCAN_{BUS,TGT,LUN} > > (mmcprobe1:dw_mmc_sim1:0:0:0): (noperiph:sdhci_slot0:0:0:0): done with PROBE_RESET > > XPT_SCAN_{BUS,TGT,LUN} > > (noperiph:sdhci_slot0:0:0:0): (mmcprobe1:dw_mmc_sim1:0:0:0): Set up the mmcprobe device... > > Probe PROBE_RESET to PROBE_SEND_IF_COND > > (mmcprobe0:sdhci_slot0:0:0:0): (mmcprobe1:dw_mmc_sim1:0:0:0): Periph created > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > Probe started > > (mmcprobe1:dw_mmc_sim1:0:0:0): (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe1:dw_mmc_sim1:0:0:0): Probe PROBE_INVALID to PROBE_RESET > > Start with PROBE_SEND_IF_COND > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_RESET > > (mmcprobe0:sdhci_slot0:0:0:0): (mmcprobe1:dw_mmc_sim1:0:0:0): Start with PROBE_IDENTIFY > > IF_COND: error 1, pattern 00000000 > > (mmcprobe1:dw_mmc_sim1:0:0:0): Probe PROBE_SEND_IF_COND to PROBE_SDIO_RESET > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_start > > (mmcprobe1:dw_mmc_sim1:0:0:0): Start with PROBE_SDIO_RESET > > (mmcprobe1:dw_mmc_sim1:0:0:0): SDIO_RESET: error 1, CCCR CTL register: 00000000 > > (mmcprobe1:dw_mmc_sim1:0:0:0): Probe PROBE_SDIO_RESET to PROBE_SDIO_INIT > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_start > > (mmcprobe1:dw_mmc_sim1:0:0:0): Start with PROBE_SDIO_INIT > > (mmcprobe1:dw_mmc_sim1:0:0:0): SDIO_INIT: error 1, 00000000 00000000 00000000 00000000 > > (mmcprobe1:dw_mmc_sim1:0:0:0): Probe PROBE_SDIO_INIT to PROBE_SEND_APP_OP_COND > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_start > > (mmcprobe1:dw_mmc_sim1:0:0:0): APP_OP_COND: error 1, resp 00000000 > > (mmcprobe1:dw_mmc_sim1:0:0:0): Probe PROBE_SEND_APP_OP_COND to PROBE_MMC_INIT > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_start > > (mmcprobe1:dw_mmc_sim1:0:0:0): Start with PROBE_MMC_INIT > > (mmcprobe1:dw_mmc_sim1:0:0:0): MMC_INIT: error 1, resp 00000000 > > (mmcprobe1:dw_mmc_sim1:0:0:0): Probe PROBE_MMC_INIT to PROBE_INVALID > > (mmcprobe1:dw_mmc_sim1:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe1:dw_mmc_sim1:0:0:0): Periph invalidated > > (mmcprobe1:dw_mmc_sim1:0:0:0): Periph destroyed > > uhub5: 1 port with 1 removable, self powered > > uhub1: 1 port with 1 removable, self powered > > (mmcprobe0:sdhci_slot0:0:0:0): Send first XPT_MMC_IO > > (mmcprobe0:sdhci_slot0:0:0:0): done with PROBE_RESET > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_RESET to PROBE_SEND_IF_COND > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_SEND_IF_COND > > (mmcprobe0:sdhci_slot0:0:0:0): IF_COND: error 1, pattern 00000000 > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_SEND_IF_COND to PROBE_SDIO_RESET > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_SDIO_RESET > > (mmcprobe0:sdhci_slot0:0:0:0): SDIO_RESET: error 1, CCCR CTL register: 00000000 > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_SDIO_RESET to PROBE_SDIO_INIT > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_SDIO_INIT > > (mmcprobe0:sdhci_slot0:0:0:0): SDIO_INIT: error 1, 00000000 00000000 00000000 00000000 > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_SDIO_INIT to PROBE_SEND_APP_OP_COND > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): APP_OP_COND: error 1, resp 00000000 > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_SEND_APP_OP_COND to PROBE_MMC_INIT > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_MMC_INIT > > (mmcprobe0:sdhci_slot0:0:0:0): MMC card, OCR 40ff8080 > > (mmcprobe0:sdhci_slot0:0:0:0): -> sending OCR to card > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_MMC_INIT > > (mmcprobe0:sdhci_slot0:0:0:0): MMC card, OCR 40ff8080 > > (mmcprobe0:sdhci_slot0:0:0:0): Card is still powering up > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_MMC_INIT > > (mmcprobe0:sdhci_slot0:0:0:0): MMC card, OCR 40ff8080 > > (mmcprobe0:sdhci_slot0:0:0:0): Card is still powering up > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_MMC_INIT > > (mmcprobe0:sdhci_slot0:0:0:0): MMC card, OCR c0ff8080 > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_MMC_INIT to PROBE_GET_CID > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): CID 45010044413431323801ad0efc3e3600 > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_GET_CID to PROBE_MMC_SET_RELATIVE_ADDR > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_MMC_SET_RELATIVE_ADDR to PROBE_GET_CSD > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): CSD d00f00328f5903ffffffffef8a404000 > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_GET_CSD to PROBE_SELECT_CARD > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Probe PROBE_SELECT_CARD to PROBE_DONE > > (mmcprobe0:sdhci_slot0:0:0:0): mmcprobe_done: remaining freeze count 0 > > (noperiph:sdhci_slot0:0:0:0): (mmcprobe0:sdhci_slot0:0:0:0): xpt_async(AC_FOUND_DEVICE) > > mmcprobe_start > > (mmcprobe0:sdhci_slot0:0:0:0): Start with PROBE_DONE > > (mmcprobe0:sdhci_slot0:0:0:0): Periph invalidated > > (mmcprobe0:sdhci_slot0:0:0:0): Periph destroyed > > (sdda0:sdhci_slot0:0:0:0): Periph created > > (pass0:sdhci_slot0:0:0:0): Periph created > > (sdda0:sdhci_slot0:0:0:0): Capacity: 125069950976, sectors: 244277248 > > (sdda0:sdhci_slot0:0:0:0): Set SD freq to 25 MHz (min out of host f=25 MHz and card f=52 MHz) > > (sdda0:sdhci_slot0:0:0:0): Set bus width to 8-bit (min of host 8-bit and card 8-bit) > > (sdda0:sdhci_slot0:0:0:0): Partition type 'default', size 125069950976 > > (sdda0:sdhci_slot0:0:0:0): Partition type 'boot0', size 4194304 > > (sdda0:sdhci_slot0:0:0:0): Partition type 'boot1', size 4194304 > > (sdda0:sdhci_slot0:0:0:0): Partition type 'RPMB', size 16777216 > > (sdda0:sdhci_slot0:0:0:0): Don't know what to do with RPMB partitions yet > > sdda0 at sdhci_slot0 bus 0 scbus2 target 0 lun 0 > > sdda0: Relative addr: 00000002 > > Card features: <MMC Memory High-Capacity> > > Card memory OCR: 40ff8080 > > sdda0: Serial Number AD0EFC3E > > (sdda0:sdhci_slot0:0:0:0): XPT info: CLK 25000000, ... > > sdda0: MMCHC DA4128 0.1 SN AD0EFC3E MFG 03/2003 by 69 0x0000 > > (sdda0:sdhci_slot0:0:0:0): Partition 0 -> 1 > > g_dev_taste: make_dev_alias_p() failed (name=mmcsd0, error=17) > > (sdda0:sdhci_slot0:0:0:0): Partition 1 -> 2 > > (sdda0:sdhci_slot0:0:0:0): Partition 2 -> 0 > > ugen5.2: <Realtek USB 10/100/1000 LAN> at usbus5 > > ure0 on uhub4 > > ure0: <Realtek USB 10/100/1000 LAN, class 0/0, rev 3.00/30.00, addr 1> on usbus5 > > miibus0: <MII bus> on ure0 > > rgephy0: <RTL8251/8153 1000BASE-T media interface> PHY 0 on miibus0 > > rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto > > ue0: <USB Ethernet> on ure0 > > ue0: Ethernet address: a0:ce:c8:de:9c:95 > > ugen2.2: <vendor 0x05e3 USB2.0 Hub> at usbus2 > > uhub6 on uhub5 > > uhub6: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/85.36, addr 2> on usbus2 > > ugen1.2: <HAILUCK CO.,LTD USB KEYBOARD> at usbus1 > > ukbd0 on uhub3 > > ukbd0: <HAILUCK CO.,LTD USB KEYBOARD, class 0/0, rev 1.10/1.00, addr 2> on usbus1 > > kbd1 at ukbd0 > > ums0 on uhub3 > > ums0: <HAILUCK CO.,LTD USB KEYBOARD, class 0/0, rev 1.10/1.00, addr 2> on usbus1 > > ums0: 3 buttons and [XY] coordinates ID=1 > > Root mount waiting for: usbus2 > > uhub6: 4 ports with 4 removable, self powered > > ugen2.3: <Sonix Technology Co., Ltd. USB Camera> at usbus2 > > mountroot: waiting for device /dev/mmcsd0p3... > > WARNING: /: TRIM flag on fs but disk does not support TRIM > > Dual Console: Serial Primary, Video Secondary > > lock order reversal: > > 1st 0xffffa00007850770 ufs (ufs, lockmgr) @ /usr/src/sys/kern/vfs_mount.c:1780 > > 2nd 0xffffa00005e52e70 devfs (devfs, lockmgr) @ /usr/src/sys/kern/vfs_subr.c:3035 > > lock order devfs -> ufs established at: > > #0 0xffff0000004d7670 at witness_checkorder+0x444 > > #1 0xffff000000439744 at lockmgr_lock_flags+0x1d8 > > #2 0xffff0000006debac at ffs_lock+0x64 > > #3 0xffff0000005647ac at _vn_lock+0x54 > > #4 0xffff000000544fb8 at vfs_domount+0xeb0 > > #5 0xffff000000543058 at vfs_donmount+0x2b4 > > #6 0xffff00000054783c at kernel_mount+0x4c > > #7 0xffff000000549fd8 at parse_mount+0x49c > > #8 0xffff000000548520 at vfs_mountroot+0x400 > > #9 0xffff0000003f7448 at start_init+0x24 > > #10 0xffff000000424198 at fork_exit+0x74 > > #11 0xffff00000076716c at fork_trampoline+0x14 > > lock order ufs -> devfs attempted at: > > #0 0xffff0000004d7e7c at witness_checkorder+0xc50 > > #1 0xffff00000043b198 at lockmgr_xlock+0x50 > > #2 0xffff0000005647ac at _vn_lock+0x54 > > #3 0xffff00000054e6c4 at vget_finish+0x4c > > #4 0xffff000000318328 at devfs_allocv+0xd0 > > #5 0xffff000000317ab8 at devfs_root+0x44 > > #6 0xffff000000553bb0 at vfs_cache_root_fallback+0x154 > > #7 0xffff00000054f944 at vflush+0x5c > > #8 0xffff0000003179c0 at devfs_unmount+0x34 > > #9 0xffff000000545e4c at dounmount+0x43c > > #10 0xffff0000005459c8 at kern_unmount+0x2d4 > > #11 0xffff000000767a40 at do_el0_sync+0x4a4 > > #12 0xffff000000746a1c at handle_el0_sync+0x90 > > dwwdt0: <Synopsys Designware watchdog timer> mem 0xff848000-0xff8480ff irq 47 on ofwbus0 > > pwm_backlight0: <PWM Backlight> on ofwbus0 > > mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0 > > mx25l0: device type gd25q128, size 16384K in 256 sectors of 64K, erase size 4K > > lo0: link state changed to UP > > ue0: link state changed to DOWN > > ue0: link state changed to UP > > > > > > Is there any patches to enable SDIO on Broadcom BCM43456 ? > > > > Best regards > > --- > > Kazuhiko Kiriyama <[email protected]> > > > --- > Kazuhiko Kiriyama <[email protected]> > > > >