Re: [14-CURRENT]BBB can't boot 14-CURRENT GENERICSD-20210805

I applied ti_sysc.c patch with 14.0-CURRENT-arm-armv7-GENERICSD-20210805.

Unfortunately, I got another panic(No usable event timer found!)

ofwbus0: <Open Firmware Device Tree>
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
regfix0: <Fixed Regulator> on ofwbus0
clk_fixed0: <Fixed clock> on ofwbus0
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
<snip>
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpufreq_dt0: <Generic cpufreq driver> on cpu0
cpufreq_dt0: no regulator for cpu@0
device_attach: cpufreq_dt0 attach returned 6
ti_sysc0: <TI SYSC Interconnect> on ofwbus0
device_attach: ti_sysc0 attach returned 6
gpioled0: <GPIO LEDs> on ofwbus0
gpioled0: <beaglebone:green:heartbeat> failed to map pin
gpioled0: <beaglebone:green:mmc0> failed to map pin
gpioled0: <beaglebone:green:usr2> failed to map pin
gpioled0: <beaglebone:green:usr3> failed to map pin
panic: No usable event timer found! <-----------------------------PANIC

I compared between13-stable and 14-current.
14-current kernel can't attach clock management.
ti_prcm0: <TI Power and Clock Management> mem 0-0x1fff on ti_sysc0

If I replace dtb directory(I got from 13-stable dtb directory and I put FAT
partition dtb and /boot/dtb), 14-GENERICSD can't boot....


2021年8月15日(日) 0:12 Mark Johnston <[email protected]>:

> On Sat, Aug 14, 2021 at 06:15:37PM +0900, Yoshiro MIHIRA wrote:
> > I can use 13.0-STABLE-arm-armv7-GENERICSD-20210812 on Beaglebone
> Black[OK].
> >
> > However, I tested 14-CURRENT GENERICSD-20210805 on Beaglebone Black.
> > It can't boot with the below message[NG].
> >
> > Please let me know to solve this issue.
> >
> > If I use the same microSD on Raspberry PI2, it can boot without issue.
> > I put all boot console messages.
> >
> https://people.freebsd.org/~sanpei/20210814-boot-NG-14-GENERICSD-20210805
> >
> > <<BOOT message>
> > mem: <memory>
> > ofwbus0: <Open Firmware Device Tree>
> > ti_sysc0: <TI SYSC Interconnect> on ofwbus0
> > panic: Assertion size > 0 failed at /usr/src/sys/kern/subr_vmem.c:1332
>
> I guess that the DTB has changed somehow such that this error path
> is getting exercised.  This patch should allow you to boot without
> panicking, at least.
>
> diff --git a/sys/arm/ti/ti_sysc.c b/sys/arm/ti/ti_sysc.c
> index b16158aa5d83..4fda12f05725 100644
> --- a/sys/arm/ti/ti_sysc.c
> +++ b/sys/arm/ti/ti_sysc.c
> @@ -306,6 +306,8 @@ parse_regfields(struct ti_sysc_softc *sc) {
>
>         /* Grab the content of reg properties */
>         nreg = OF_getproplen(node, "reg");
> +       if (nreg == -1)
> +               return (ENXIO);
>         reg = malloc(nreg, M_DEVBUF, M_WAITOK);
>         OF_getencprop(node, "reg", reg, nreg);
>
>