Rock64 eMMC not working
John-Mark Gurney <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.arm |
|---|---|
| Message-ID | <[email protected]> |
Hello, I am trying to get the latest FreeBSD -current snapshot to boot/run off a Pine64 eMMC module on the Rock64, but I'm seeing an issue w/ mounting root: FreeBSD 14.0-CURRENT #0 main-n254105-d53927b0bae: Thu Mar 31 09:26:31 UTC 2022 [...] Trying to mount root from ufs:/dev/ufs/rootfs [rw]... mmcsd0: Error indicated: 4 Failed I got similar messages when 13.1-RC1: mmcsd0: 16GB <MMCHC M8B16G 2.8 SN D808D122 MFG 07/2018 by 136 0x0003> at mmc0 150.0MHz/8bit/1016-block mmcsd0boot0: 4MB partition 1 at mmcsd0 mmcsd0boot1: 4MB partition 2 at mmcsd0 mmcsd0rpmb: 4MB partition 3 at mmcsd0 [...] GEOM: mmcsd0: the secondary GPT header is not in the last LBA. mmcsd0: Error indicated: 4 Failed rockchip_dwmmc1: Failed to update clk Are there any known issues w/ this? A different image to try? Also, in trying to debug this issue, I tried to boot from a microSD card with the eMMC module installed by shorting the jumper, but when I did, I got: mmcsd0: 32GB <SDHC GB1QT 3.0 SN xxx MFG 03/2020 by 27 SM> at mmc0 50.0MHz/4bit/1016-block mmcsd1: Error reading EXT_CSD Failed device_attach: mmcsd1 attach returned 6 Kernel page fault with the following non-sleepable locks held: exclusive sleep mutex rockchip_dwmmc1 (dwmmc) r = 0 (0xffffa000008d2128) locked @ /usr/src/sys/dev/mmc/host/dwmmc.c:386 stack backtrace: #0 0xffff0000004e5390 at witness_debugger+0x5c #1 0xffff0000004e6564 at witness_warn+0x3e8 #2 0xffff00000078962c at data_abort+0xa0 #3 0xffff000000767810 at handle_el1h_sync+0x10 x0: 8088 x1: ffff00008e18b000 (ucom_cons_softc + 8ce4ca40) x2: 40 x3: 182 x4: 0 x5: ffff00008e1767a0 (ucom_cons_softc + 8ce381e0) x6: 0 x7: 0 x8: 4 x9: ffff000000b55910 (memmap_bus + 0) x10: 3 x11: 10000 x12: 1 x13: 2af8 x14: 88 x15: 2af8 x16: 88 x17: 0 x18: ffff00008e176850 (ucom_cons_softc + 8ce38290) x19: ffffa000008d2140 x20: ffffa000008d2000 x21: 8088 x22: 0 x23: 80000003 x24: ffffa000008c9580 x25: ffffa00000bb9100 x26: ffff000000b9ea98 (Giant + 18) x27: ffff0000008df336 (digits + ea96) x28: ffffa00000bb9110 x29: ffff00008e176850 (ucom_cons_softc + 8ce38290) sp: ffff00008e176850 lr: ffff0000007b0298 (dwmmc_intr + 50) elr: ffff0000007b02c4 (dwmmc_intr + 7c) spsr: 45 far: 20 esr: 96000044 panic: data abort in critical section or under mutex cpuid = 0 time = 1 KDB: stack backtrace: db_trace_self() at db_trace_self db_trace_self_wrapper() at db_trace_self_wrapper+0x30 vpanic() at vpanic+0x174 panic() at panic+0x44 data_abort() at data_abort+0x2dc handle_el1h_sync() at handle_el1h_sync+0x10 --- exception, esr 0x96000044 dwmmc_intr() at dwmmc_intr+0x7c ithread_loop() at ithread_loop+0x2a0 fork_exit() at fork_exit+0x74 fork_trampoline() at fork_trampoline+0x14 KDB: enter: panic Complete boot message: ====================== U-Boot TPL 2021.07 (Mar 31 2022 - 05:26:18) LPDDR3, 800MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2021.07 (Mar 31 2022 - 05:26:18 +0000) Trying to boot from MMC1 Card did not respond to voltage select! : -110 spl: mmc init failed with error: -95 Trying to boot from MMC2 NOTICE: BL31: v2.5(release): NOTICE: BL31: Built : 05:24:37, Mar 31 2022 NOTICE: BL31:Rockchip release version: v1.2 U-Boot 2021.07 (Mar 31 2022 - 05:28:19 +0000) Model: Pine64 Rock64 DRAM: 2 GiB PMIC: RK8050 (on=0x40, off=0x00) MMC: mmc@ff500000: 1, mmc@ff520000: 0 Loading Environment from MMC... Card did not respond to voltage select! : -110 *** Warning - No block device, using default environment In: serial@ff130000 Out: serial@ff130000 Err: serial@ff130000 Model: Pine64 Rock64 Net: eth0: ethernet@ff540000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... 50618 bytes read in 7 ms (6.9 MiB/s) Card did not respond to voltage select! : -110 Scanning disk [email protected]... Disk [email protected] not ready Scanning disk [email protected]... ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** ** Unrecognized filesystem type ** Found 5 disks ** Unable to read file ubootefi.var ** Failed to load EFI variables BootOrder not defined EFI boot manager: Cannot load any image Found EFI removable media binary efi/boot/bootaa64.efi 1263868 bytes read in 33 ms (36.5 MiB/s) Booting /efi\boot\bootaa64.efi Consoles: EFI console Reading loader env vars from /efi/freebsd/loader.env Setting currdev to disk0p1: FreeBSD/arm64 EFI loader, Revision 1.1 (Thu Mar 31 08:48:02 UTC 2022 [email protected]) Command line arguments: loader.efi Image base: 0x7cdde000 EFI version: 2.80 EFI Firmware: Das U-Boot (rev 8225.1792) Console: efi (0x1000) Load Path: /efi\boot\bootaa64.efi Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(1)/HD(1,GPT,64400726-b60c-11ec-a26d-85c343ffa803,0x8000,0x19000) Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(1)/HD(1,GPT,64400726-b60c-11ec-a26d-85c343ffa803,0x8000,0x19000) Setting currdev to disk0p1: Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(0)/eMMC(1)/HD(2,GPT,64400726-b60c-11ec-a26d-85c343ffa803,0x21000,0x1cc6fd8) Setting currdev to disk0p2: / Loading /boot/defaults/loader.conf Loading /boot/defaults/loader.conf Loading /boot/device.hints Loading /boot/loader.conf Loading /boot/loader.conf.local / Loading kernel... /boot/kernel/kernel text=0x2a8 text=0x84f4a0 text=0x249adc data=0x1b9aa8 data=0x0+0x40d000 0x8+0x133de8+0x8+0x15b370\ Loading configured modules... /boot/entropy size=0x1000 /boot/kernel/umodem.ko text=0x2100 text=0x13a0 data=0x6d8+0x10 0x8+0xf18+0x8+0xb5c loading required module 'ucom' /boot/kernel/ucom.ko text=0x2590 text=0x2f00 data=0x8e0+0x858 0x8+0x1290+0x8+0xbd5 /etc/hostid size=0x25 Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... Using DTB provided by EFI at 0x80f0000. EFI framebuffer information: addr, size 0x0, 0x0 dimensions 0 x 0 stride 0 masks 0x00000000, 0x00000000, 0x00000000, 0x00000000 ---<<BOOT>>--- GDB: debug ports: uart GDB: current port: uart KDB: debugger backends: ddb gdb KDB: current backend: ddb Copyright (c) 1992-2022 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 14.0-CURRENT #0 main-n254105-d53927b0bae: Thu Mar 31 09:26:31 UTC 2022 [email protected]:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC arm64 FreeBSD clang version 13.0.0 ([email protected]:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) WARNING: WITNESS option enabled, expect reduced performance. VT: init without driver. module firmware already present! real memory = 2145136640 (2045 MB) avail memory = 2065342464 (1969 MB) Starting CPU 1 (1) Starting CPU 2 (2) Starting CPU 3 (3) FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs random: unblocking device. random: entropy device external interface MAP 7cf1b000 mode 2 pages 1 MAP 7cf1f000 mode 2 pages 3 MAP 7cf23000 mode 2 pages 4 MAP 7ff40000 mode 2 pages 16 kbd0 at kbdmux0 ofwbus0: <Open Firmware Device Tree> clk_fixed0: <Fixed clock> on ofwbus0 rk_grf0: <RockChip General Register Files> mem 0xff100000-0xff100fff on ofwbus0 rk3328_cru0: <Rockchip RK3328 Clock and Reset Unit> mem 0xff440000-0xff440fff on ofwbus0 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 Cannot set frequency for clk: aclk_bus_pre_c, error: 34 rk3328_cru0: Failed to set aclk_bus_pre to a frequency of 15000000 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 Cannot set frequency for clk: aclk_peri_pre, error: 34 rk3328_cru0: Failed to set aclk_peri_pre to a frequency of 15000000 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy Cannot get frequency for clk: hdmi_phy, error: 9 clk_fixed1: <Fixed clock> on ofwbus0 regfix0: <Fixed Regulator> on ofwbus0 regfix1: <Fixed Regulator> on ofwbus0 regfix2: <Fixed Regulator> on ofwbus0 regfix3: <Fixed Regulator> on ofwbus0 simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0xff450000-0xff45ffff on ofwbus0 psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 gic0: <ARM Generic Interrupt Controller> mem 0xff811000-0xff811fff,0xff812000-0xff813fff,0xff814000-0xff815fff,0xff816000-0xff817fff irq 52 on ofwbus0 gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 160 rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0 gpio0: <RockChip GPIO Bank controller> mem 0xff210000-0xff2100ff irq 53 on rk_pinctrl0 gpiobus0: <OFW GPIO bus> on gpio0 gpio1: <RockChip GPIO Bank controller> mem 0xff220000-0xff2200ff irq 54 on rk_pinctrl0 gpiobus1: <OFW GPIO bus> on gpio1 gpio2: <RockChip GPIO Bank controller> mem 0xff230000-0xff2300ff irq 55 on rk_pinctrl0 gpiobus2: <OFW GPIO bus> on gpio2 gpio3: <RockChip GPIO Bank controller> mem 0xff240000-0xff2400ff irq 56 on rk_pinctrl0 gpiobus3: <OFW GPIO bus> on gpio3 rk_i2c0: <RockChip I2C> mem 0xff160000-0xff160fff irq 16 on ofwbus0 iicbus0: <OFW I2C bus> on rk_i2c0 rk805_pmu0: <RockChip RK805 PMIC> at addr 0x30 irq 57 on iicbus0 generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000 Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000 rk_tsadc0: <RockChip temperature sensors> mem 0xff250000-0xff2500ff irq 24 on ofwbus0 cpulist0: <Open Firmware CPU Group> on ofwbus0 cpu0: <Open Firmware CPU> on cpulist0 cpufreq_dt0: <Generic cpufreq driver> on cpu0 cpufreq_dt0: Found cpu-supply cpu1: <Open Firmware CPU> on cpulist0 cpufreq_dt1: <Generic cpufreq driver> on cpu1 cpufreq_dt1: Found cpu-supply cpu2: <Open Firmware CPU> on cpulist0 cpufreq_dt2: <Generic cpufreq driver> on cpu2 cpufreq_dt2: Found cpu-supply cpu3: <Open Firmware CPU> on cpulist0 cpufreq_dt3: <Generic cpufreq driver> on cpu3 cpufreq_dt3: Found cpu-supply pcm0: <simple-audio-card> on ofwbus0 pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0 pcm1: <simple-audio-card> on ofwbus0 i2s0: <Rockchip I2S> mem 0xff000000-0xff000fff irq 8 on ofwbus0 Cannot set frequency for clk: xin12m, error: 34 Cannot set frequency for clk: xin12m, error: 34 i2s1: <Rockchip I2S> mem 0xff010000-0xff010fff irq 9 on ofwbus0 Cannot set frequency for clk: clkin_i2s1, error: 34 Cannot set frequency for clk: xin12m, error: 34 uart0: <16750 or compatible> mem 0xff130000-0xff1300ff irq 14 on ofwbus0 uart0: console (1500000,n,8,1) iic0: <I2C generic I/O> on iicbus0 spi0: <Rockchip SPI> mem 0xff190000-0xff190fff irq 19 on ofwbus0 spibus0: <OFW SPI bus> on spi0 spibus0: <unknown card> at cs 0 mode 0 rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xff500000-0xff503fff irq 43 on ofwbus0 rockchip_dwmmc0: Hardware version ID is 270a rockchip_dwmmc1: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xff520000-0xff523fff irq 45 on ofwbus0 rockchip_dwmmc1: Hardware version ID is 270a mmc0: <MMC/SD bus> on rockchip_dwmmc1 dwc0: <Rockchip Gigabit Ethernet Controller> mem 0xff540000-0xff54ffff irq 46 on ofwbus0 miibus0: <MII bus> on dwc0 rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on miibus0 rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto dwc0: Ethernet address: xxx dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0xff580000-0xff5bffff irq 48 on ofwbus0 usbus1 on dwcotg0 ehci0: <Generic EHCI Controller> mem 0xff5c0000-0xff5cffff irq 49 on ofwbus0 usbus2: EHCI version 1.0 usbus2 on ehci0 ohci0: <Generic OHCI Controller> mem 0xff5d0000-0xff5dffff irq 50 on ofwbus0 usbus3 on ohci0 gpioc0: <GPIO controller> on gpio0 gpioc1: <GPIO controller> on gpio1 gpioc2: <GPIO controller> on gpio2 gpioc3: <GPIO controller> on gpio3 gpioled0: <GPIO LEDs> on ofwbus0 gpioled0: <led-0> failed to map pin gpioled0: <led-1> failed to map pin pcm2: <simple-audio-card> on ofwbus0 armv8crypto0: <AES-CBC,AES-XTS,AES-GCM> Timecounters tick every 1.000 msec usbus1: 480Mbps High Speed USB v2.0 usbus2: 480Mbps High Speed USB v2.0 usbus3: 12Mbps Full Speed USB v1.0 rk805_pmu0: registered as a time-of-day clock, resolution 1.000000s pcm0: no driver attached to codec node pcm1: no driver attached to codec node ugen2.1: <Generic EHCI root HUB> at usbus2 uhub0 on usbus2 uhub0: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2 ugen1.1: <DWCOTG OTG Root HUB> at usbus1 uhub1 on usbus1 uhub1: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 ugen3.1: <Generic OHCI root HUB> at usbus3 uhub2 on usbus3 uhub2: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 mmcsd0: 16GB <MMCHC M8B16G 2.8 SN xxx MFG 07/2018 by 136 0x0003> at mmc0 150.0MHz/8bit/1016-block mmcsd0boot0: 4MB partition 1 at mmcsd0 mmcsd0boot1: 4MB partition 2 at mmcsd0 mmcsd0rpmb: 4MB partition 3 at mmcsd0 pcm2: no driver attached to cpu node CPU 0: ARM Cortex-A53 r0p4 affinity: 0 Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL> Instruction Set Attributes 1 = <> Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32> Processor Features 1 = <> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> Memory Model Features 1 = <8bit VMID> Memory Model Features 2 = <32bit CCIDX,48bit VA> Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8> Debug Features 1 = <> Auxiliary Features 0 = <> Auxiliary Features 1 = <> AArch32 Instruction Set Attributes 5 = <CRC32,SHA2,SHA1,AES+VMULL,SEVL> AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD> AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ> CPU 1: ARM Cortex-A53 r0p4 affinity: 1 CPU 2: ARM Cortex-A53 r0p4 affinity: 2 CPU 3: ARM Cortex-A53 r0p4 affinity: 3 Release APs...done WARNING: WITNESS option enabled, expect reduced performance. Unresolved linked clock found: hdmi_phy Unresolved linked clock found: usb480m_phy Trying to mount root from ufs:/dev/ufs/rootfs [rw]... mmcsd0: Error indicated: 4 Failed uhub2: 1 port with 1 removable, self powered uhub1: 1 port with 1 removable, self powered uhub0: 1 port with 1 removable, self powered -- John-Mark Gurney Voice: +1 415 225 5579 "All that I will do, has been done, All that I have, has not."