https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=277268
Bug ID: 277268
Summary: RPi4: LOR in gpioled(4)
Product: Base System
Version: 15.0-CURRENT
Hardware: arm64
OS: Any
Status: New
Severity: Affects Some People
Priority: ---
Component: arm
Assignee: [email protected]
Reporter: [email protected]
while booting, the kernel reports a LOR in gpioled(4). the system appears to
work fine aside from this (i am not using the LED driver).
gpioled0: <GPIO LEDs> on ofwbus0
lock order reversal: (sleepable after non-sleepable)
1st 0xffff000000dd5678 LED mtx (LED mtx, sleep mutex) @
/usr/src/sys/dev/led/led.c:295
2nd 0xffffa000013f8810 Raspberry Pi firmware gpio (Raspberry Pi firmware gpio,
sx) @ /usr/src/sys/arm/broadcom/bcm2835/raspberrypi_gpio.c:250
lock order LED mtx -> Raspberry Pi firmware gpio attempted at:
#0 0xffff0000005257e0 at witness_checkorder+0xa78
#1 0xffff0000004ba384 at _sx_xlock+0x70
#2 0xffff00000092a8e8 at rpi_fw_gpio_pin_set+0xe4
#3 0xffff0000001dc00c at led_create_state+0x15c
#4 0xffff0000001a2f34 at gpioled_attach+0x294
#5 0xffff0000004ec360 at device_attach+0x3fc
#6 0xffff0000004ebec8 at device_probe_and_attach+0x80
#7 0xffff0000004ee4d4 at bus_generic_new_pass+0x100
#8 0xffff0000004ee484 at bus_generic_new_pass+0xb0
#9 0xffff0000004ee484 at bus_generic_new_pass+0xb0
#10 0xffff0000004e8d60 at bus_set_pass+0x50
#11 0xffff00000043138c at mi_startup+0x1e0
#12 0xffff0000000008a8 at virtdone+0x68
uma_zalloc_debug: zone "malloc-64" with the following non-sleepable locks held:
exclusive sleep mutex LED mtx (LED mtx) r = 0 (0xffff000000dd5678) locked @
/usr/src/sys/dev/led/led.c:295
stack backtrace:
#0 0xffff000000525c50 at witness_debugger+0x60
#1 0xffff000000526ee4 at witness_warn+0x40c
#2 0xffff0000007eaa9c at uma_zalloc_debug+0x34
#3 0xffff0000007ea628 at uma_zalloc_arg+0x30
#4 0xffff000000481aa4 at malloc+0x90
#5 0xffff00000091f568 at bcm2835_firmware_property+0x48
#6 0xffff00000092a900 at rpi_fw_gpio_pin_set+0xfc
#7 0xffff0000001dc00c at led_create_state+0x15c
#8 0xffff0000001a2f34 at gpioled_attach+0x294
#9 0xffff0000004ec360 at device_attach+0x3fc
#10 0xffff0000004ebec8 at device_probe_and_attach+0x80
#11 0xffff0000004ee4d4 at bus_generic_new_pass+0x100
#12 0xffff0000004ee484 at bus_generic_new_pass+0xb0
#13 0xffff0000004ee484 at bus_generic_new_pass+0xb0
#14 0xffff0000004e8d60 at bus_set_pass+0x50
#15 0xffff00000043138c at mi_startup+0x1e0
#16 0xffff0000000008a8 at virtdone+0x68
related: bug 248490 which was closed as "overcome by events" but the issue is
still present.
full dmesg:
---<<BOOT>>---
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance
Copyright (c) 1992-2024 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 15.0-CURRENT #0 main-n268454-9097284b98be: Thu Feb 22 06:04:22 UTC 2024
[email protected]:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC
arm64
FreeBSD clang version 17.0.6 (https://github.com/llvm/llvm-project.git
llvmorg-17.0.6-0-g6009708b4367)
WARNING: WITNESS option enabled, expect reduced performance.
VT(efifb): resolution 592x448
module scmi already present!
real memory = 2067783680 (1971 MB)
avail memory = 1988354048 (1896 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofw_clkbus0
clk_fixed1: <Fixed clock> on ofw_clkbus0
clk_fixed2: <Fixed clock> on ofwbus0
clk_fixed3: <Fixed clock> on ofwbus0
simplebus1: <Flattened device tree simple bus> on ofwbus0
simplebus2: <Flattened device tree simple bus> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
regfix3: <Fixed Regulator> on ofwbus0
regfix4: <Fixed Regulator> on ofwbus0
simplebus3: <Flattened device tree simple bus> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on
simplebus0
bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gic0: <ARM Generic Interrupt Controller> mem
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff
irq 30 on simplebus0
gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on
simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
gpiobus1: <GPIO bus> on gpio1
regfix0: Cannot configure GPIO pin: 5
REGNODE_INIT failed: 6
regfix0: Cannot register regulator.
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
regfix2: Cannot set GPIO pin: 6
REGNODE_INIT failed: 6
regfix2: Cannot register regulator.
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on
simplebus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gpioregulator0: <GPIO controlled regulator> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq
31,32,33,34,35,36,37,38,39,40,41 on simplebus0
usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on
simplebus0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0
uart0: console (115200,n,8,1)
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on
simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24
on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 27 on
simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem
0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on simplebus0
bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on simplebus0
gpioc1: <GPIO controller> on gpio1
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fb0: keeping existing fb bpp of 32
fbd0 on fb0
WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 15.0.
VT: Replacing driver "efifb" with new "fb".
fb0: 592x448(592x448@0,0) 32bpp
fb0: fbswap: 1, pitch 2368, base 0x3eaf5000, screen_size 1060864
sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff irq 79
on simplebus1
mmc1: <MMC/SD bus> on sdhci_bcm1
pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
pcib0: <BCM2838-compatible PCI-express controller> mem 0x7d500000-0x7d50930f
irq 80,81 on simplebus2
pcib0: hardware identifies as revision 0x304.
pci0: <OFW PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 91 at device 0.0 on pci0
pci1: <OFW PCI bus> on pcib1
bcm_xhci0: <VL805 USB 3.0 controller (on the Raspberry Pi 4b)> irq 92 at device
0.0 on pci1
bcm_xhci0: 32 bytes context size, 64-bit DMA
usbus0 on bcm_xhci0
genet0: <RPi4 Gigabit Ethernet> mem 0x7d580000-0x7d58ffff irq 82,83 on
simplebus2
genet0: GENET version 5.0 phy 0x0000
miibus0: <MII bus> on genet0
brgphy0: <BCM54213PE 1000BASE-T media interface> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
genet0: Ethernet address: d8:3a:dd:53:f7:59
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gpioled0: <GPIO LEDs> on ofwbus0
lock order reversal: (sleepable after non-sleepable)
1st 0xffff000000dd5678 LED mtx (LED mtx, sleep mutex) @
/usr/src/sys/dev/led/led.c:295
2nd 0xffffa000013f8810 Raspberry Pi firmware gpio (Raspberry Pi firmware gpio,
sx) @ /usr/src/sys/arm/broadcom/bcm2835/raspberrypi_gpio.c:250
lock order LED mtx -> Raspberry Pi firmware gpio attempted at:
#0 0xffff0000005257e0 at witness_checkorder+0xa78
#1 0xffff0000004ba384 at _sx_xlock+0x70
#2 0xffff00000092a8e8 at rpi_fw_gpio_pin_set+0xe4
#3 0xffff0000001dc00c at led_create_state+0x15c
#4 0xffff0000001a2f34 at gpioled_attach+0x294
#5 0xffff0000004ec360 at device_attach+0x3fc
#6 0xffff0000004ebec8 at device_probe_and_attach+0x80
#7 0xffff0000004ee4d4 at bus_generic_new_pass+0x100
#8 0xffff0000004ee484 at bus_generic_new_pass+0xb0
#9 0xffff0000004ee484 at bus_generic_new_pass+0xb0
#10 0xffff0000004e8d60 at bus_set_pass+0x50
#11 0xffff00000043138c at mi_startup+0x1e0
#12 0xffff0000000008a8 at virtdone+0x68
uma_zalloc_debug: zone "malloc-64" with the following non-sleepable locks held:
exclusive sleep mutex LED mtx (LED mtx) r = 0 (0xffff000000dd5678) locked @
/usr/src/sys/dev/led/led.c:295
stack backtrace:
#0 0xffff000000525c50 at witness_debugger+0x60
#1 0xffff000000526ee4 at witness_warn+0x40c
#2 0xffff0000007eaa9c at uma_zalloc_debug+0x34
#3 0xffff0000007ea628 at uma_zalloc_arg+0x30
#4 0xffff000000481aa4 at malloc+0x90
#5 0xffff00000091f568 at bcm2835_firmware_property+0x48
#6 0xffff00000092a900 at rpi_fw_gpio_pin_set+0xfc
#7 0xffff0000001dc00c at led_create_state+0x15c
#8 0xffff0000001a2f34 at gpioled_attach+0x294
#9 0xffff0000004ec360 at device_attach+0x3fc
#10 0xffff0000004ebec8 at device_probe_and_attach+0x80
#11 0xffff0000004ee4d4 at bus_generic_new_pass+0x100
#12 0xffff0000004ee484 at bus_generic_new_pass+0xb0
#13 0xffff0000004ee484 at bus_generic_new_pass+0xb0
#14 0xffff0000004e8d60 at bus_set_pass+0x50
#15 0xffff00000043138c at mi_startup+0x1e0
#16 0xffff0000000008a8 at virtdone+0x68
armv8crypto0: CPU lacks AES instructions
Timecounters tick every 1.000 msec
usbus0: 5.0Gbps Super Speed USB v3.0
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active
command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
ugen0.1: <(0x1106) XHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <(0x1106) XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active
command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active
command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active
command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
mmc0: No compatible cards found on bus
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
mmcsd0: 16GB <SDHC SC16G 8.0 SN 4DB2AB14 MFG 05/2022 by 3 SD> at mmc1
50.0MHz/4bit/65535-block
bcm2835_cpufreq0: ARM 600MHz, Core 200MHz, SDRAM 400MHz, Turbo OFF
CPU 0: ARM Cortex-A72 r0p3 affinity: 0
Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT
ICache,64 byte ERG,64 byte CWG>
Instruction Set Attributes 0 = <CRC32>
Instruction Set Attributes 1 = <>
Instruction Set Attributes 2 = <>
Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
Processor Features 1 = <>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB
PA>
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6
Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <CRC32,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP
VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP
Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU 1: ARM Cortex-A72 r0p3 affinity: 1
CPU 2: ARM Cortex-A72 r0p3 affinity: 2
CPU 3: ARM Cortex-A72 r0p3 affinity: 3
gic0: using for IPIs
Release APs...done
TCP_ratelimit: Is now initialized
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
uhub0: 5 ports with 4 removable, self powered
WARNING: / was not properly dismounted
Warning: no time-of-day clock registered, system time will not be set
accurately
Dual Console: Serial Primary, Video Secondary
ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.21, addr 1> on usbus0
uhub1: 4 ports with 4 removable, self powered
genet0: link state changed to UP
lo0: link state changed to UP
genet0: link state changed to DOWN
genet0: link state changed to UP
Security policy loaded: MAC/ntpd (mac_ntpd)
--
You are receiving this mail because:
You are the assignee for the bug.
lmpx.com only provides a reader for public news (NNTP) servers. It is not
affiliated with the servers or forums shown here and is not responsible for
the content of articles, which is written by their respective authors.