Re: Raimbow screen installing / booting FreeBSD-14.2-RELEASE-arm64-aarch64-RPI.img on the raspberry pi zero 2w

On Feb 5, 2025, at 23:51, Tomek CEDRO <[email protected]> wrote:

> On Wed, Feb 5, 2025 at 2:59 AM Mark Millard <[email protected]> wrote:
>> On Feb 4, 2025, at 17:39, Mario Marietto <[email protected]> wrote:
>>> ----> A better alternative experiment would likely be to:
>>> I did :
>>> marietto# cp bcm2710-rpi-3-b.dtb bcm2710-rpi-zero-2-w.dtb
>>> and the board booted wonderfully without one only problem.
>>> I think that it's a good idea to add a note on the bug report that the patches created don't work and that the fix,for the moment is :
>>> marietto# cp bcm2710-rpi-3-b.dtb bcm2710-rpi-zero-2-w.dtb
>> 
>> Why not try sysutils/rpi-firmware and copying over the
>> /usr/local/share/rpi-firmware/bcm2710-rpi-zero-2-w.dtb
>> that is actually for the RPi* that you have? It is the
>> same vintage of materials as is on the official media.
>> 
>> If it does not work, that would be good to have in the
>> notes as well. Similarly, if it does work it would be
>> good to have that noted.
> 
> Yup, I can confirm rpi-firmware/bcm2710-rpi-zero-2-w.dtb works with
> FreeBSD-14.2-RELEASE-arm64-aarch64-RPI.img :-)

FreeBSD-14.2-RELEASE-arm64-aarch64-RPI.img contains the
u-boot from:

/usr/ports/sysutils/u-boot-rpi-arm64

and, so, also contains and should be used with a copy of:

/usr/local/share/rpi-firmware/config_arm64.txt

as config.txt :

# grep -rA1 config_arm64 /usr/src/release/
/usr/src/release/arm64/RPI.conf: chroot ${CHROOTDIR} cp -p ${DTB_DIR}/config_arm64.txt \
/usr/src/release/arm64/RPI.conf- ${FATMOUNT}/config.txt

/usr/local/share/rpi-firmware/config_rpi3.txt is for when:

/usr/ports/sysutils/u-boot-rpi3

is is use instead. No modern snapshot or release uses that:

# grep -r config_config_rpi3 /usr/src/release/
#

/usr/local/share/rpi-firmware/config_rpi_0_w.txt is for when:

/usr/ports/sysutils/u-boot-rpi-0-w

is is use instead. An rpi-0-w is not a arm64 / aarch64 system.

# grep -r config_rpi_0_w /usr/src/release/
#

> One thing to mention too is config_rpi3.txt -> config.txt (not
> config_rpi_0_w.txt) :-)

config_rpi3.txt is likely not fully appropriate and
config_arm64.txt is likely what should be used. But
it was already in place as config.txt in:

FreeBSD-14.2-RELEASE-arm64-aarch64-RPI.img

FreeBSD-14.2-RELEASE-arm64-aarch64-RPI.img is for
all the aarch64 / arm64 RPi*'s that FreeBSD happens
to support. (RPi5's not being supported as stands.)

> Thanks!! :-)
> 
> ps/2: pkg does not update because of certificate errors, but
> freebsd-update fetch install went fine to 14.2-RELEASE-p1 o_O


===
Mark Millard
marklmi at yahoo.com