Nanopi R5S and U-boot from Ports

Hi,

have anyone ever tested this router and got to have all 3 NIC's?

I am trying to use the u-boot r5s package from pkg, as opposed to using
edk2 firmware. Using edk2 firmware I get all three NIC's.

I got to try the u-boot, but I just have the eqos0:

root@OPNsense:~ # pciconf -vl
pcib1@pci0:0:0:0: class=0x060400 rev=0x01 hdr=0x01 vendor=0x1d87
device=0x3566 subvendor=0x0000 subdevice=0x0000
vendor = 'Rockchip Electronics Co., Ltd'
device = 'RK3568 Remote Signal Processor'
class = bridge
subclass = PCI-PCI
root@OPNsense:~ # cat /boot/loader.conf.local
# Realtek kmod R5S - version 1.98
if_re_load="YES"
if_re_name="/boot/modules/if_re.ko"
root@OPNsense:~ # ifconfig
eqos0: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP>
metric 0 mtu 1500
description: LAN (lan)
options=80008<VLAN_MTU,LINKSTATE>
ether xxxxxxxxxxxx
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
inet6 fe80::2xxxxxx%eqos0 prefixlen 64 scopeid 0x1
media: Ethernet autoselect (1000baseT <full-duplex,master>)
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
lo0: flags=1008049<UP,LOOPBACK,RUNNING,MULTICAST,LOWER_UP> metric 0 mtu 16384
options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
enc0: flags=0 metric 0 mtu 1536
options=0
groups: enc
nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
pflog0: flags=20100<PROMISC,PPROMISC> metric 0 mtu 33152
options=0
groups: pflog
pfsync0: flags=0 metric 0 mtu 1500
options=0
maxupd: 128 defer: off version: 1400
syncok: 1
groups: pfsync

root@OPNsense:~ # kldstat
Id Refs Address Size Name
1 29 0xffff000000000000 13d6ba8 kernel
2 1 0xffff0000013d7000 294d8 if_gre.ko
3 1 0xffff000001401000 22f18 pflog.ko
4 3 0xffff000001424000 8f488 pf.ko
5 1 0xffff0000014b5000 2eee8 carp.ko
6 1 0xffff0000014e4000 240f0 if_enc.ko
7 1 0xffff000001509000 2e678 if_bridge.ko
8 2 0xffff000001538000 27470 bridgestp.ko
9 1 0xffff000001560000 31d88 if_lagg.ko
10 2 0xffff000001592000 23460 if_infiniband.ko
11 1 0xffff0000015b6000 305d8 pfsync.ko
12 1 0xffff0000015e7000 a82b0 if_re.ko
13 1 0xffff0000c4a00000 22000 hym8563.ko
14 1 0xffff0000c4a22000 27000 nullfs.ko

This is an opnsense for arm64 I built here at home. I use the
realtek-re-kmod198.

I put some more info on the FreeBSD Forum:
https://forums.freebsd.org/threads/nanopi-r5s-and-freebsd-14.88967/

thanks,

matheus