14.2-RELEASE install hangs on RPi 3 & 4 Model B
Joseph Olatt <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.arm |
|---|---|
| Message-ID | <[email protected]> |
Greetings.
I have been tring to install FreeBSD 14.2-RELEASE on the following 2
RPis:
(1) Raspberry Pi 3 Model B
(2) Raspberry Pi 4 Model B
and the install process has been hanging after the lines:
...
TCP_ratelimit: Is now initialized
ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.21, addr 1> on
usbus0
NOTE: Full transcript from serial console at the end of the email
To try to narrow down the problem, I installed 13.4-RELEASE on the RPi 4
and the install went through without a hitch. Then I did "freebsd-update
upgrade -r 14.2-RELEASE" and after the 1st reboot (as part of the
upgrade process), it started hanging at the aforementioned line.
Has anybody else successfully fresh-installed 14.2-RELEASE on one or
both of the RPis in question?
Thank you.
joseph
/*Begin transcript from serial console */
U-Boot 2024.04 (Sep 13 2024 - 04:40:06 +0000)
DRAM: 948 MiB (effective 3.9 GiB)
RPI 4 Model B (0xc03114)
console comconsole failed to initialize
Consoles: EFI console
Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p1:
FreeBSD/arm64 EFI loader, Revision 3.0
Command line arguments: loader.efi
Image base: 0x39ddc000
EFI version: 2.100
EFI Firmware: Das U-Boot (rev 8228.1024)
Console: efi,comconsole (0)
Load Path: /efi\boot\bootaa64.efi
Load Device:
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000003000000)/SD(0)/SD(1)/HD(1,0x01,0,0x800,0x19000)
BootOrder: 0000
Trying ESP:
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000003000000)/SD(0)/SD(1)/HD(1,0x01,0,0x800,0x19000)
Setting currdev to disk0p1:
Trying:
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000003000000)/SD(0)/SD(1)/HD(2,0x01,0,0x19800,0x1d92800)
Setting currdev to disk0p2:
**********************************************************************
**********************************************************************
***** *****
***** BOOT LOADER IS TOO OLD. PLEASE UPGRADE. *****
***** *****
**********************************************************************
**********************************************************************
Loading /boot/defaults/loader.conf
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.local
Loading kernel...
/boot/kernel/kernel text=0x2a8 text=0x9ecb90 text=0x2675f4 data=0x1520f8
data=0x0+0x2bc000 0x8+0x1541a0+0x8+0x17d712
Loading configured modules...
/boot/kernel/umodem.ko text=0x2040 text=0x1340 data=0x6f8+0x4
0x8+0xeb8+0x8+0xb2c
loading required module 'ucom'
/boot/kernel/ucom.ko text=0x249f text=0x3380 data=0x920+0x858
0x8+0x1170+0x8+0xb13
/boot/entropy size=0x1000
/etc/hostid size=0x25
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by EFI at 0x39ef9000.
EFI framebuffer information:
addr, size 0x3eaf5000, 0x103000
dimensions 592 x 448
stride 592
masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000
---<<BOOT>>---
WARNING: Cannot find freebsd,dts-version property, cannot check DTB
compliance
Copyright (c) 1992-2023 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of Foundation.
FreeBSD 14.2-RELEASp1 GENERIC arm64
FreeBSD clang version 18.1.6 (https://github.com/llvm/llvm-project.git
llvmorg-18.1.6-0-g1118c2e05e67)
VT(efifb): resolution 592x448
module scmi already present!
real memory = 4148158464 (3955 MB)
avail memory = 4020584448 (3834 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on ofwbus0
simplebus2: <Flattened device tree simple bus> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
regfix3: <Fixed Regulator> on ofwbus0
regfix4: <Fixed Regulator> on ofwbus0
simplebus3: <Flattened device tree simple bus> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem
0x7d5d2000-0x7d5d2eff on simplebus0
bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gic0: <ARM Generic Interrupt Controller> mem
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff
irq 30 on simplebus0
gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq
14,15 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
gpiobus1: <GPIO bus> on gpio1
regfix0: Cannot configure GPIO pin: 5
REGNODE_INIT failed: 6
regfix0: Cannot register regulator.
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
regfix2: Cannot set GPIO pin: 6
REGNODE_INIT failed: 6
regfix2: Cannot register regulator.
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on
simplebus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gpioregulator0: <GPIO controlled regulator> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq
31,32,33,34,35,36,37,38,39,40,41 on simplebus0
usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on
simplebus0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on
simplebus0
uart0: console (115200,n,8,1)
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on
simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 modesdhci_bcm0: <Broadcom 2708 SDHCI
controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 27
on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem
0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on
simplebus0
bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on
simplebus0
gpioc1: <GPIO controller> on gpio1
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fb0: keeping existing fb bpp of 32
fbd0 on fb0
WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD
15.0.
VT: Replacing driver "efifb" with new "fb".
fb0: 592x448(592x448@0,0) 32bpp
fb0: fbswap: 1, pitch 2368, base 0x3eaf5000, screen_size 1060864
sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff
irq 79 on simplebus1
mmc1: <MMC/SD bus> on sdhci_bcm1
pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
pcib0: <BCM2838-compatible PCI-express controller> mem
0x7d500000-0x7d50930f irq 80,81 on simplebus2
pcib0: hardware identifies as revision 0x304.
pci0: <OFW PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 91 at device 0.0 on pci0
pci1: <OFW PCI bus> on pcib1
bcm_xhci0: <VL805 USB 3.0 controller (on the Raspberry Pi 4b)> irq 92 at
device 0.0 on pci1
bcm_xhci0: 32 bytes context size, 64-bit DMA
usbus0 on bcm_xhci0
genet0: <RPi4 Gigabit Ethernet> mem 0x7d580000-0x7d58ffff irq 82,83 on
simplebus2
genet0: GENET version 5.0 phy 0x0000
miibus0: <MII bus> on genet0
brgphy0: <BCM54213PE 1000BASE-T media interface> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
genet0: Ethernet address: e4:5f:01:40:4d:18
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gpioled0: <GPIO LEDs> on ofwbus0
armv8crypto0: CPU lacks AES instructions
Timecounters tick every 1.000 msec
usbus0: 5.0Gbps Super Speed USB v3.0
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no
active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ================================gen0.1: <(0x1106) XHCI
root HUB> at usbus0
uhub0 on usbus0
uhub0: <(0x1106) XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
usbus0
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no
active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Ver 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00slot0: Int enab:
0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-sl000 | Caps2: 0x00000000
sdhcdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no
active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x0-slot0: Int enab:
0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Ca_bcm0-slot0: Max curr:
0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no
active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x0000-slot0:
Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA sdhci_bcm0-slot0: ADMA
addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no
active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no
active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no
active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x0000000lot0: Caps:
0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slont: 0x00000000
sdhci_bcm0-slot0atible cards found on bus
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
mmcsd0: 16GB <SDHC SC16G 8.0 SN 41D2B8E3 MFG 12/2020 by 3 SD> at mmc1
50.0MHz/4bit/65535-block
bcm2835_cpufreq0: ARM 600MHz, Core 200MHz, SDRAM 400MHz, Turbo OFF
uhub0: 5 ports with 4 removable, self powered
CPU 0: ARM Cortex-A72 r0p3 affinity: 0
Cache Type = <64 byte D-cacheline,64 byte
I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG>
Instruction Set Attributes 0 = <CRC32>
Instruction Set Attributes 1 = <>
Instruction Set Attributes 2 = <>
Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
Processor Features 1 = <>
Processor Features 2 = <>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit
ASID,16TB PA>
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Memory Model Features 3 = <>
Memory Model Features 4 = <>
Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6
Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <CRC32,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP
VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP
Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU 1: ARM Cortex-A72 r0p3 affinity: 1
CPU 2: ARM Cortex-A72 r0p3 affinity: 2
CPU 3: ARM Cortex-A72 r0p3 affinity: 3
gic0: using for IPIs
Release APs...done
TCP_ratelimit: Is now initialized
ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.21, addr 1> on
usbus0
/*End transcript from serial console */