Re: KHADAS EDGE V booting hangs if I install UEFI instead of u-boot

You can read about the procedure that I have followed from this first post
on the FreeBSD forum :

https://forums.freebsd.org/threads/how-to-boot-freebsd-installed-on-the-sd-card-on-the-khadas-edge-v-instead-of-android.98463/post-710783

(don't worry,that's not a long thread).



On Wed, Aug 6, 2025 at 5:44 AM Mark Millard <[email protected]> wrote:

> On Aug 5, 2025, at 20:04, Mario Marietto <[email protected]> wrote:
>
> > Hello.
> > Finally I’ve been able to setup a serial connection with the board with
> the goal to understand why the KHADAS EDGE V does not boot FreeBSD if I
> make the installation of UEFI instead of u-boot and I’ve gathered these log
> messages :
>
> I only have a basic type note here:
>
> What you show below references "uboot" as something
> being loaded.
>
> > Boot1: 2018-08-06, version: 1.15
> > CPUId = 0x0
> > ChipType = 0x10, 218
> > SdmmcInit=2 0
> > BootCapSize=100000
> > UserCapSize=29820MB
> > FwPartOffset=2000 , 100000
> > mmc0:cmd5,20
> > SdmmcInit=0 0
> > BootCapSize=0
> > UserCapSize=121942MB
> > FwPartOffset=2000 , 0
> > run on sd0
> > StorageInit ok = 89823
> > SecureMode = 0
> > SecureInit read PBA: 0x4
> > SecureInit read PBA: 0x404
> > SecureInit read PBA: 0x804
> > SecureInit read PBA: 0xc04
> > SecureInit read PBA: 0x1004
> > SecureInit read PBA: 0x1404
> > SecureInit read PBA: 0x1804
> > SecureInit read PBA: 0x1c04
> > SecureInit ret = 0, SecureMode = 0
> > GPT 0x3190d20 signature is wrong
> > LoadTrust Addr:0x4000
> > No find bl30.bin
> > No find bl32.bin
> > Load uboot, ReadLba = 2000
>
> Note the "uboot" above. Seems to be loading a U-Boot.
>
> > Load OK, addr=0x200000, size=0xf0000
>
> Note that the "uboot" loaded OK.
>
> >
> > RunBL31 0x10000
> > NOTICE: BL31: v1.3(debug):51f2096
> > NOTICE: BL31: Built : 16:24:31, May 6 2019
> > NOTICE: BL31: Rockchip release version: v1.1
> > INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized
> in EL3
> > INFO: Using opteed sec cpu_context!
> > INFO: boot cpu mask: 0
> > INFO: plat_rockchip_pmu_init(1181): pd status 3e
> > INFO: BL31: Initializing runtime services
> > WARNING: No OPTEE provided by BL2 boot loader, Booting device without
> OPTEE initialization. SMC`s dK
> > ERROR: Error initializing runtime service opteed_fast
> > INFO: BL31: Preparing for EL3 exit to normal world
> > INFO: Entry point address = 0x200000
> > INFO: SPSR = 0x3c9
> > PLL at FF750000: fbdiv=112, refdiv=2, postdiv1=2, postdiv2=1,
> vco=1344000 khz, output=672000 khz
> > Boot PLLs:
> > APLLL = 400000000
> > APLLB = 24000000
> > CPLL = 24000000
> > DPLL = 800000000
> > GPLL = 400000000
> > NPLL = 24000000
> > VPLL = 24000000
> > PLL at FF760000: fbdiv=68, refdiv=1, postdiv1=2, postdiv2=1, vco=1632000
> khz, output=816000 khz
> > PLL at FF760020: fbdiv=68, refdiv=1, postdiv1=2, postdiv2=1, vco=1632000
> khz, output=816000 khz
> > PLL at FF760080: fbdiv=100, refdiv=1, postdiv1=3, postdiv2=1,
> vco=2400000 khz, output=800000 khz
> > PLL at FF7600A0: fbdiv=125, refdiv=1, postdiv1=3, postdiv2=1,
> vco=3000000 khz, output=1000000 khz
> > PLL at FF760060: fbdiv=100, refdiv=1, postdiv1=3, postdiv2=1,
> vco=2400000 khz, output=800000 khz
> > After clock init:
> > APLLL = 816000000
> > APLLB = 816000000
> > CPLL = 800000000
> > DPLL = 800000000
> > GPLL = 800000000
> > NPLL = 1000000000
> > VPLL = 24000000
> > PLL at FF760000: fbdiv=54, refdiv=1, postdiv1=1, postdiv2=1, vco=1296000
> khz, output=1296000 khz
> > PLL at FF760020: fbdiv=70, refdiv=1, postdiv1=1, postdiv2=1, vco=1680000
> khz, output=1680000 khz
> > �������� : FROZEN : No more messages.
> >
> >
> > it’s not clear why it hangs. Do you have a vague idea why it hangs there
> ?
> > And more important,do you know where / to whom I can ask ?
> > Don't suggest to me the KHADAS forum. I detected a low quality of help
> for the newbies if they have complicated problems to solve.
> > Their help is good only for the business users. I'm not.
> > Thanks.
>
> I do not see any evidence above that UEFI was involved.
> (But I've never dealt with a KHADAS EDGE V.)
>
> Looks like an attempted "uboot" based boot to me.
>
> You may need to give a lot more detail about how you
> have things set up, possibly for both a working U-Boot
> (if you have such a context) and for what you did to
> configure for UEFI, providing for a compare/contrast
> inspection.
>
> I have no clue what you installed that was a UEFI
> or where/how it was installed or how the system was
> told to try to put it to use.
>
> But, again, I've no knowledge of the specific type
> of context that you have so my notes are very limited.
>
> ===
> Mark Millard
> marklmi at yahoo.com
>
>

-- 
Mario.