Re: KHADAS EDGE V booting hangs if I install UEFI instead of u-boot
Mario Marietto <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.arm |
|---|---|
| Message-ID | <CA+1FSih2XY9RrOwG3R5mx0i8Cc3CbQmHXjYWXiKpWUsh0ktb2Q@mail.gmail.com> |
Welcome to minicom 2.9
OPTIONS: I18n
Port /dev/ttyUSB0, 17:17:13
Press CTRL-A Z for help on special keys
U-Boot SPL 2020.07 (Apr 19 2021 - 09:29:52 +0300)
Trying to boot from MMC1
U-Boot 2020.07 (Apr 19 2021 - 09:29:52 +0300)
SoC: Rockchip rk3399
Reset cause: POR
Model: Khadas Edge-V
DRAM: 3.9 GiB
PMIC: RK808
MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPI Flash... SF: Detected w25q128fw with page size
256 Bytes, erase size 4B
*** Warning - bad CRC, using default environment
In: serial
Out: vidconsole
Err: vidconsole
Model: Khadas Edge-V
Net: eth0: ethernet@fe300000
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Unrecognized filesystem type **
Consoles: EFI console
Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p1:
FreeBSD/arm64 EFI loader, Revision 1.1
Command line arguments: loader.efi
Image base: 0xf0dcd000
EFI version: 2.80
EFI Firmware: Das U-Boot (rev 8224.1792)
Console: comconsole (0)
Load Path: /efi\boot\bootaa64.efi
Load Device:
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(1,GPT,c06dc639-cc50-11e)
Trying ESP:
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(1,GPT,c06dc639-cc50-11eb-b8)
Setting currdev to disk0p1:
Trying:
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(2,GPT,c06dc639-cc50-11eb-b8a0-d)
Setting currdev to disk0p2:
Trying:
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(3,GPT,c06dc639-cc50-11eb-b8a0-d)
Setting currdev to disk0p3:
\
Loading /boot/defaults/loader.conf
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.local
cLoading kernel...
/boot/kernel/kernel text=0x2a8 text=0x7bfa34 text=0x1c9d54 data=0x183ff8
data=0x0+0x384000 syms=[0]/
Loading configured modules...
/boot/entropy size=0x1000
/etc/hostid size=0x25
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by EFI at 0x80ea000.
EFI framebuffer information:
addr, size 0xf6000000, 0x7e9000
dimensions 1920 x 1080
stride 1920
masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.0-RELEASE-p1 #0: Sun Jun 13 17:07:42 MSK 2021
[email protected]:/usr/crochet/work/obj/usr/crochet/src-release-13.0/arm64.aarch64/sys/EXPER4
FreeBSD clang version 11.0.1 ([email protected]:llvm/llvm-project.git
llvmorg-11.0.1-0-g43ff75f2c3fe)
VT(efifb): resolution 1920x1080
real memory = 4158345216 (3965 MB)
avail memory = 4026830848 (3840 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
Starting CPU 4 (100)
Starting CPU 5 (101)
FreeBSD/SMP: Multiprocessor System Detected: 6 CPUs
random: unblocking device.
random: entropy device external interface
MAP f0f07000 mode 2 pages 1
MAP f0f0d000 mode 2 pages 2
MAP f3f30000 mode 2 pages 16
WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD
14.0.
kbd0 at kbdmux0
WARNING: Device "openfirm" is Giant locked and may be deleted before
FreeBSD 14.0.
ofwbus0: <Open Firmware Device Tree>
clk_fixed0: <Fixed clock> on ofwbus0
simplebus0: <Flattened device tree simple bus> on ofwbus0
rk_grf0: <RockChip General Register Files> mem 0xff320000-0xff320fff on
ofwbus0
rk3399_pmucru0: <Rockchip RK3399 PMU Clock and Reset Unit> mem
0xff750000-0xff750fff on ofwbus0
rk3399_cru0: <Rockchip RK3399 Clock and Reset Unit> mem
0xff760000-0xff760fff on ofwbus0
rk_grf1: <RockChip General Register Files> mem 0xff770000-0xff77ffff on
ofwbus0
clk_fixed1: <Fixed clock> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
regfix3: <Fixed Regulator> on ofwbus0
regfix4: <Fixed Regulator> on ofwbus0
regfix5: <Fixed Regulator> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem
0xff310000-0xff310fff on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller v3.0> mem
0xfee00000-0xfee0ffff,0xfef00000-0xfefbffff,0xfff0
its0: <ARM GIC Interrupt Translation Service> mem 0xfee20000-0xfee3ffff on
gic0
rk_iodomain0: <RockChip IO Voltage Domain> mem 0xff320000-0xff320fff on
rk_grf0
rk_iodomain1: <RockChip IO Voltage Domain> mem 0-0xff76ffff,0-0xffff on
rk_grf1
rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0
gpio0: <RockChip GPIO Bank controller> mem 0xff720000-0xff7200ff irq 71 on
rk_pinctrl0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <RockChip GPIO Bank controller> mem 0xff730000-0xff7300ff irq 72 on
rk_pinctrl0
gpiobus1: <OFW GPIO bus> on gpio1
gpio2: <RockChip GPIO Bank controller> mem 0xff780000-0xff7800ff irq 73 on
rk_pinctrl0
gpiobus2: <OFW GPIO bus> on gpio2
gpio3: <RockChip GPIO Bank controller> mem 0xff788000-0xff7880ff irq 74 on
rk_pinctrl0
gpiobus3: <OFW GPIO bus> on gpio3
gpio4: <RockChip GPIO Bank controller> mem 0xff790000-0xff7900ff irq 75 on
rk_pinctrl0
gpiobus4: <OFW GPIO bus> on gpio4
rk_i2c0: <RockChip I2C> mem 0xff130000-0xff130fff irq 22 on ofwbus0
iicbus0: <OFW I2C bus> on rk_i2c0
rk_i2c1: <RockChip I2C> mem 0xff3d0000-0xff3d0fff irq 39 on ofwbus0
iicbus1: <OFW I2C bus> on rk_i2c1
syr8270: <Silergy SYR827 regulator> at addr 0x80 on iicbus1
rk_i2c2: <RockChip I2C> mem 0xff3e0000-0xff3e0fff irq 40 on ofwbus0
iicbus2: <OFW I2C bus> on rk_i2c2
rk80x_pmu0: <RockChip RK808 PMIC> at addr 0x36 irq 76 on iicbus1
rk80x_pmu0: registered as a time-of-day clock, resolution 1.000000s
generic_timer0: <ARMv8 Generic Timer> irq 2,3,4,5 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
rk_tsadc0: <RockChip temperature sensors> mem 0xff260000-0xff2600ff irq 35
on ofwbus0
rk_usb2phy0: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_usb2phy1: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_emmcphy0: <Rockchip RK3399 eMMC PHY> mem 0-0xff76ffff,0-0xffff on
rk_grf1
rk_pcie_phy0: <Rockchip RK3399 PCIe PHY> mem 0-0xff76ffff,0-0xffff on
rk_grf1
rk_typec_phy0: <Rockchip RK3399 PHY TYPEC> mem 0xff7c0000-0xff7fffff on
ofwbus0
rk_typec_phy1: <Rockchip RK3399 PHY TYPEC> mem 0xff800000-0xff83ffff on
ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpufreq_dt0: <Generic cpufreq driver> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpufreq_dt1: <Generic cpufreq driver> on cpu1
cpu2: <Open Firmware CPU> on cpulist0
cpufreq_dt2: <Generic cpufreq driver> on cpu2
cpu3: <Open Firmware CPU> on cpulist0
cpufreq_dt3: <Generic cpufreq driver> on cpu3
cpu4: <Open Firmware CPU> on cpulist0
cpufreq_dt4: <Generic cpufreq driver> on cpu4
cpu5: <Open Firmware CPU> on cpulist0
cpufreq_dt5: <Generic cpufreq driver> on cpu5
pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0
pmu1: <Performance Monitoring Unit> irq 1 on ofwbus0
pcib0: <Rockchip PCIe controller> mem
0xf8000000-0xf9ffffff,0xfd000000-0xfdffffff irq 6,7,8 on ofwb0
pcib0: Gen1 link training timeouted: 0x00080001.
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 0.0 on pci0
pcib0: failed to reserve resource for pcib1
pcib1: failed to allocate initial memory window: 0-0xfffff
pci1: <PCI bus> on pcib1
dwc0: <Rockchip Gigabit Ethernet Controller> mem 0xfe300000-0xfe30ffff irq
9 on ofwbus0
miibus0: <MII bus> on dwc0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseT-FDX, 1000baseT-FDX-mastero
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseT-FDX, 1000baseT-FDX-mastero
dwc0: Ethernet address: 62:43:94:13:10:0c
rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller
(RockChip)> mem 0xfe310000-0xf0
rockchip_dwmmc0: Hardware version ID is 270a
rockchip_dwmmc1: <Synopsys DesignWare Mobile Storage Host Controller
(RockChip)> mem 0xfe320000-0xf0
rockchip_dwmmc1: Hardware version ID is 270a
mmc0: <MMC/SD bus> on rockchip_dwmmc1
sdhci_fdt0: <Rockchip RK3399 fdt SDHCI controller> mem
0xfe330000-0xfe33ffff irq 12 on ofwbus0
rk_emmcphy0: got emmcclk clock
sdhci_fdt0-slot0: Hardware doesn't specify timeout clock frequency, setting
BROKEN_TIMEOUT quirk.
sdhci_fdt0: 1 slot(s) allocated
mmc1: <MMC/SD bus> on sdhci_fdt0
ehci0: <Generic EHCI Controller> mem 0xfe380000-0xfe39ffff irq 13 on
ofwbus0
usbus0: EHCI version 1.0
usbus0 on ehci0
ohci0: <Generic OHCI Controller> mem 0xfe3a0000-0xfe3bffff irq 14 on
ofwbus0
usbus1 on ohci0
ehci1: <Generic EHCI Controller> mem 0xfe3c0000-0xfe3dffff irq 15 on
ofwbus0
usbus2: EHCI version 1.0
usbus2 on ehci1
ohci1: <Generic OHCI Controller> mem 0xfe3e0000-0xfe3fffff irq 16 on
ofwbus0
usbus3 on ohci1
rk_dwc30: <Rockchip RK3399 DWC3> on ofwbus0
xhci0: Only host mode is supported
xhci0: Only host mode is supported
rk_dwc31: <Rockchip RK3399 DWC3> on ofwbus0
xhci0: <Synopsys Designware DWC3> mem 0xfe900000-0xfe9fffff irq 78 on
rk_dwc31
xhci0: 64 bytes context size, 32-bit DMA
usbus4: trying to attach
usbus4 on xhci0
iic0: <I2C generic I/O> on iicbus0
uart0: <16750 or compatible> mem 0xff180000-0xff1800ff irq 26 on ofwbus0
uart1: <16750 or compatible> mem 0xff1a0000-0xff1a00ff irq 28 on ofwbus0
uart1: console (1500000,n,8,1)
iicbus1: <unknown card> at addr 0x82
iic1: <I2C generic I/O> on iicbus1
iic2: <I2C generic I/O> on iicbus2
pwm0: <Rockchip PWM> mem 0xff420000-0xff42000f on ofwbus0
pwmbus0: <OFW PWM bus> on pwm0
pwmc0: <PWM Control> channel 0 on pwmbus0
pwm1: <Rockchip PWM> mem 0xff420020-0xff42002f on ofwbus0
pwmbus1: <OFW PWM bus> on pwm1
pwmc1: <PWM Control> channel 0 on pwmbus1
i2s0: <Rockchip I2S> mem 0xff880000-0xff880fff irq 51 on ofwbus0
Cannot set frequency for clk: clkin_i2s, error: 34
Cannot set frequency for clk: xin24m, error: 34
i2s1: <Rockchip I2S> mem 0xff890000-0xff890fff irq 52 on ofwbus0
Cannot set frequency for clk: clkin_i2s, error: 34
Cannot set frequency for clk: xin24m, error: 34
i2s2: <Rockchip I2S> mem 0xff8a0000-0xff8a0fff irq 53 on ofwbus0
Cannot set frequency for clk: clkin_i2s, error: 34
Cannot set frequency for clk: xin24m, error: 34
pcm0: <simple-audio-card> on ofwbus0
hdmiaudio0: <Rockchip HDMI Audio Hack> mem 0xff940000-0xff95ffff irq 60 on
ofwbus0
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
gpioc2: <GPIO controller> on gpio2
gpioc3: <GPIO controller> on gpio3
gpioc4: <GPIO controller> on gpio4
gpioled0: <GPIO LEDs> on ofwbus0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <Generic EHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Generic OHCI root HUB> at usbus1
uhub1 on usbus1
uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
ugen2.1: <Generic EHCI root HUB> at usbus2
uhub2 on usbus2
uhub2: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Generic OHCI root HUB> at usbus3
uhub3 on usbus3
uhub3: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
usbus4: 5.0Gbps Super Speed USB v3.0
uhub1: 1 port with 1 removable, self powered
ugen4.1: <Synopsys XHCI root HUB> at usbus4
uhub4 on usbus4
uhub4: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus4
mmcsd0: 128GB <SDHC SD128 8.5 SN B7E83B69 MFG 10/2020 by 3 SD> at mmc0
50.0MHz/4bit/1021-block
uhub3: 1 port with 1 removable, self powered
mmcsd1: 31GB <MMCHC BJTD4R 0.9 SN F84B4A79 MFG 11/2022 by 21 0x0000> at
mmc1 49.5MHz/8bit/65535-blok
mmcsd1boot0: 4MB partition 1 at mmcsd1
mmcsd1boot1: 4MB partition 2 at mmcsd1
mmcsd1rpmb: 4MB partition 3 at mmcsd1
pcm0: failed to set sysclk for codec node
pcm0: failed to set sysclk for codec node
pcm0: failed to set sysclk for codec node
pcm0: failed to set sysclk for codec node
Release APs...done
CPU 0: ARM Cortex-A53 r0p4 affinity: 0 0
Cache Type = <64 byte D-cacheline,64 byte
I-cacheline,VIPT ICache,64 byte ERG,64>
Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL>
Instruction Set Attributes 1 = <>
Processor Features 0 = <GIC,AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
Processor Features 1 = <>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB
PA>
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Debug Features 0 = <2 CTX BKPTs,4 Watchpoints,6
Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
CPU 1: ARM Cortex-A53 r0p4 affinity: 0 1
Cache Type = <64 byte D-cacheline,64 byte
I-cacheline,VIPT ICache,64 byte ERG,64>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB
PA>
CPU 2: ARM Cortex-A53 r0p4 affinity: 0 2
Cache Type = <64 byte D-cacheline,64 byte
I-cacheline,VIPT ICache,64 byte ERG,64>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB
PA>
CPU 3: ARM Cortex-A53 r0p4 affinity: 0 3
Cache Type = <64 byte D-cacheline,64 byte
I-cacheline,VIPT ICache,64 byte ERG,64>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB
PA>
CPU 4: ARM Cortex-A72 r0p2 affinity: 1 0
Cache Type = <64 byte D-cacheline,64 byte
I-cacheline,PIPT ICache,64 byte ERG,64>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit
ASID,16TB PA>
CPU 5: ARM Cortex-A72 r0p2 affinity: 1 1
Cache Type = <64 byte D-cacheline,64 byte
I-cacheline,PIPT ICache,64 byte ERG,64>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit
ASID,16TB PA>
uhub0: 1 port with 1 removable, self powered
Trying to mount root from ufs:/dev/gpt/install [rw,noatime]...
GEOM: mmcsd1: the primary GPT table is corrupt or invalid.
uhub4: 2 ports with 2 removable, self powered
GEOM: mmcsd1: using the secondary instead -- recovery strongly advised.
uhub2: 1 port with 1 removable, self powered
Dual Console: Serial Primary, Video Secondary
Setting hostuuid: 65386165-6635-6336-3035-383363623236.
Setting hostid: 0x1a119174.
Solaris: WARNING: ignoring tunable zfs_arc_max (using 0 instead)
Solaris: WARNING: ignoring tunable zfs_arc_max (using 3056451584 instead)
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Starting file system checks:
/dev/gpt/install: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/gpt/install: clean, 17191348 free (11716 frags, 2147454 blocks, 0.0%
fragmentation)
Mounting local filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib
/usr/local/lib/compat/pkg /usr/loca4
Setting hostname: khadas-edge.
Setting up harvesting:
[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTD
Feeding entropy: .
Autoloading module: dwwdt.ko
dwwdt0: <Synopsys Designware watchdog timer> mem 0xff848000-0xff8480ff irq
48 on ofwbus0
xhci1: Only host mode is supported
lo0: link state changed to UP
dwc0: link state changed to DOWN
Starting Network: lo0 dwc0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
dwc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8000b<RXCSUM,TXCSUM,VLAN_MTU,LINKSTATE>
ether 62:43:94:13:10:0c
media: Ethernet autoselect (none)
status: no carrier
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
Starting devd.
Autoloading module: dwwdt.ko
add host 127.0.0.1: gateway lo0 fib 0: route already in table
add host ::1: gateway lo0 fib 0: route already in table
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
Waiting 5s for the default route interface: ....
Clearing /tmp (X related).
Creating and/or trimming log files.
Updating motd:.
Updating /var/run/os-release done.
Starting syslogd.
Starting pwmfan.
Mounting late filesystems:.
Starting powerd.
Security policy loaded: MAC/ntpd (mac_ntpd)
Starting ntpd.
Starting dbus.
Starting local daemons:.
Jan 21 08:50:56 khadas-edge ntpd[981]: error resolving pool
0.freebsd.pool.ntp.org: Name does not r)
Configuring vt: keymap blanktime.
Starting cron.
Performing sanity check on sshd configuration.
Starting sshd.
Starting background file system checks in 60 seconds.
Mon Jan 21 08:51:03 UTC 2013
FreeBSD/arm64 (khadas-edge) (ttyu1)
login:
On Thu, Aug 7, 2025 at 4:26 PM Mark Millard <[email protected]> wrote:
> A question:
>
> Can you set up a working U-Boot based boot, capture
> all the output, and report it to the list?
>
> That would give something to compare/contrast with
> for the messages that have been reported so far.
>
>
> ===
> Mark Millard
> marklmi at yahoo.com
>
--
Mario.