firewire disk stopped working

My external firewire disk "Seagate FreeAgent Pro" stopped working with CURRENT 
from today. It used to work without any problems before today's update.

After plugging the cable the following error messages begin scrolling on the 
console continuously:

sbp0:0:0 sbp_scsi_status: unknown scsi status 0x0                                                                               
sbp0:0:0 Obj: Data buffer, Error: Type error                                                                                    
sbp0:0:0 sbp_scsi_status: unknown scsi status 0x0                                                                               
sbp0:0:0 Obj: Data buffer, Error: Type error                                                                                    

They stop only after the cable is unplugged. 

Information about the system:

# uname -a
FreeBSD zembla.universe 8.0-CURRENT FreeBSD 8.0-CURRENT #0: Sat Feb 14 
22:06:57 EET 2009     [email protected]:/usr/obj/usr/src/sys/CUSTOM  amd64

The output from "pciconf -lv" is: 

# pciconf -lv
fwohci0@pci0:3:3:0:     class=0x0c0010 card=0x581111c1 chip=0x581111c1 
rev=0x61 hdr=0x00
    vendor     = 'Lucent/Agere Systems (Was: AT&T MicroElectronics)'
    device     = 'FW322 1394A PCI PHY/Link Open Host Ctrlr I/F'
    class      = serial bus
    subclass   = FireWire

The output from "fwcontrol" is:

# fwcontrol
2 devices (info_len=2)
node           EUI64          status    hostname
   0  00-1c-b3-ff-fe-98-73-de      0
  -1  00-20-37-00-04-a0-34-21      0

Output from "fwcontrol -p" is:

# fwcontrol -p
=== base register ===          
0x61 0x05 0xe3 0x40 0xc0 0x03 0x00 0x20 
Physical_ID:24  R:0  CPS:1              
RHB:0  IBR:0  Gap_Count:5               
Extended:7 Num_Ports:3                  
PHY_Speed:2 Delay:0                     
LCtrl:1 C:1 Jitter:0 Pwr_Class:0
WDIE:0 ISBR:0 CTOI:0 CPSI:0 STOI:0 PEI:0 EAA:1 EMC:1
Max_Legacy_SPD:0 BLINK:0 Bridge:0
Page_Select:1 Port_Select0

=== page 0 port 0 ===
0xf8 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Astat:3 BStat:3 Ch:1 Con:0 RXOK:0 Dis:0
Negotiated_speed:0 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
DC_connected:0 Max_port_speed:0 LPP:0 Cable_speed:0
Connection_unreliable:0 Beta_mode:0
Port_error:0x0
Loop_disable:0 In_standby:0 Hard_disable:0

=== page 0 port 1 ===
0xf8 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Astat:3 BStat:3 Ch:1 Con:0 RXOK:0 Dis:0
Negotiated_speed:0 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
DC_connected:0 Max_port_speed:0 LPP:0 Cable_speed:0
Connection_unreliable:0 Beta_mode:0
Port_error:0x0
Loop_disable:0 In_standby:0 Hard_disable:0

=== page 0 port 2 ===
0xf8 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Astat:3 BStat:3 Ch:1 Con:0 RXOK:0 Dis:0
Negotiated_speed:0 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
DC_connected:0 Max_port_speed:0 LPP:0 Cable_speed:0
Connection_unreliable:0 Beta_mode:0
Port_error:0x0
Loop_disable:0 In_standby:0 Hard_disable:0

=== page 1 ===
0x01 0x00 0x00 0x60 0x1d 0x03 0x23 0x61
Compliance:1
Vendor_ID:0x00601d

Is there any way to make the disk work again?

Sincerely,

Boris Kotzev











_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-firewire
To unsubscribe, send any mail to "[email protected]"