Re: firewire disk stopped working

Also, can you send me the "dmesg" output when you connect your drive to
your system?

Sean


On Sun, 2009-02-15 at 00:12 +0200, Boris Kotzev wrote:
> My external firewire disk "Seagate FreeAgent Pro" stopped working with CURRENT 
> from today. It used to work without any problems before today's update.
> 
> After plugging the cable the following error messages begin scrolling on the 
> console continuously:
> 
> sbp0:0:0 sbp_scsi_status: unknown scsi status 0x0                                                                               
> sbp0:0:0 Obj: Data buffer, Error: Type error                                                                                    
> sbp0:0:0 sbp_scsi_status: unknown scsi status 0x0                                                                               
> sbp0:0:0 Obj: Data buffer, Error: Type error                                                                                    
> 
> They stop only after the cable is unplugged. 
> 
> Information about the system:
> 
> # uname -a
> FreeBSD zembla.universe 8.0-CURRENT FreeBSD 8.0-CURRENT #0: Sat Feb 14 
> 22:06:57 EET 2009     [email protected]:/usr/obj/usr/src/sys/CUSTOM  amd64
> 
> The output from "pciconf -lv" is: 
> 
> # pciconf -lv
> fwohci0@pci0:3:3:0:     class=0x0c0010 card=0x581111c1 chip=0x581111c1 
> rev=0x61 hdr=0x00
>     vendor     = 'Lucent/Agere Systems (Was: AT&T MicroElectronics)'
>     device     = 'FW322 1394A PCI PHY/Link Open Host Ctrlr I/F'
>     class      = serial bus
>     subclass   = FireWire
> 
> The output from "fwcontrol" is:
> 
> # fwcontrol
> 2 devices (info_len=2)
> node           EUI64          status    hostname
>    0  00-1c-b3-ff-fe-98-73-de      0
>   -1  00-20-37-00-04-a0-34-21      0
> 
> Output from "fwcontrol -p" is:
> 
> # fwcontrol -p
> === base register ===          
> 0x61 0x05 0xe3 0x40 0xc0 0x03 0x00 0x20 
> Physical_ID:24  R:0  CPS:1              
> RHB:0  IBR:0  Gap_Count:5               
> Extended:7 Num_Ports:3                  
> PHY_Speed:2 Delay:0                     
> LCtrl:1 C:1 Jitter:0 Pwr_Class:0
> WDIE:0 ISBR:0 CTOI:0 CPSI:0 STOI:0 PEI:0 EAA:1 EMC:1
> Max_Legacy_SPD:0 BLINK:0 Bridge:0
> Page_Select:1 Port_Select0
> 
> === page 0 port 0 ===
> 0xf8 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> Astat:3 BStat:3 Ch:1 Con:0 RXOK:0 Dis:0
> Negotiated_speed:0 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
> DC_connected:0 Max_port_speed:0 LPP:0 Cable_speed:0
> Connection_unreliable:0 Beta_mode:0
> Port_error:0x0
> Loop_disable:0 In_standby:0 Hard_disable:0
> 
> === page 0 port 1 ===
> 0xf8 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> Astat:3 BStat:3 Ch:1 Con:0 RXOK:0 Dis:0
> Negotiated_speed:0 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
> DC_connected:0 Max_port_speed:0 LPP:0 Cable_speed:0
> Connection_unreliable:0 Beta_mode:0
> Port_error:0x0
> Loop_disable:0 In_standby:0 Hard_disable:0
> 
> === page 0 port 2 ===
> 0xf8 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> Astat:3 BStat:3 Ch:1 Con:0 RXOK:0 Dis:0
> Negotiated_speed:0 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
> DC_connected:0 Max_port_speed:0 LPP:0 Cable_speed:0
> Connection_unreliable:0 Beta_mode:0
> Port_error:0x0
> Loop_disable:0 In_standby:0 Hard_disable:0
> 
> === page 1 ===
> 0x01 0x00 0x00 0x60 0x1d 0x03 0x23 0x61
> Compliance:1
> Vendor_ID:0x00601d
> 
> Is there any way to make the disk work again?
> 
> Sincerely,
> 
> Boris Kotzev
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> _______________________________________________
> [email protected] mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-firewire
> To unsubscribe, send any mail to "[email protected]"

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-firewire
To unsubscribe, send any mail to "[email protected]"