Re: Western Digital 1TB My Book Studio

Here is the output with the sysctl variables set. I'm at work right now, so I couldn't physically disconnect and reconnect, but I did issue a 'fwcontrol -r' to get this output. If you need an actual disconnect/reconnect, it'll have to wait a few hours.

-Steve

fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc1, gen=15, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
sbp0:0:0 request timeout(mgm orb:0x2e10b154) ... reset start
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: BUS reset
sbp_post_busreset
fwohci0: node_id=0xc800ffc1, gen=16, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
fwohci0: fw_set_bus_manager: 1->1 (loop=0)
firewire0: bus manager 1 (me)
send phy_config root_node=1 gap_count=5
fwohci0: start AT DMA status=72
node0: crom unchanged
fw_explore: node 2, err = 0
bus_explore done
sbp_post_explore (sbp_cold=0)
sbp_post_explore: EUI:0090a9341b93f349 attached
target 0 lun 0 found
target 0 lun 1 found
sbp0:0:0 ordered:1 type:0 EUI:0090a9341b93f349 node:0 speed:3 maxrec:0 new!
sbp0:0:0 'WD' 'My Book' '001025'
sbp_login: sec = 0 usec = 683278 ticks = 683
sbp0:0:1 ordered:1 type:13 EUI:0090a9341b93f349 node:0 speed:3 maxrec:0 new!
sbp0:0:1 'WD' 'My Book' '001025'
sbp_login: sec = 0 usec = 682496 ticks = 682
sbp0:0:1 LOGIN
sbp: alloc 3 xfer
sbp0:0:1 mgm orb: 2c4ad28c
sbp0:0:0 LOGIN
sbp0:0:1 request timeout(mgm orb:0x2c4ad28c) ... reset start
sbp0:0:1 sbp_reset_start


 -------------- Original message ----------------------
From: Sean Bruno <[email protected]>
> Stephen Bader wrote:
> > Is there anything I can do to help you out? I'd hate for you to go buy a drive 
> just to help me get mine working.
> >
> > -Steve
> >
> >  -------------- Original message ----------------------
> > From: Sean Bruno <[email protected]>
> >   
> >> Stephen Bader wrote:
> >>     
> >>> Here is a link to the manufacturers site for the drive:
> >>>
> >>> http://www.westerndigital.com/en/products/products.asp?driveid=374
> >>>
> >>> Thanks,
> >>>
> >>> -Steve
> >>>
> >>>  -------------- Original message ----------------------
> >>> From: Sean Bruno <[email protected]>
> >>>   
> >>>       
> >>>>> It works just fine in Windows and on Mac. I haven't tried linux yet, 
> >>>>> but if it comes down to it, I can probably find a live CD somewhere 
> >>>>> and try it out.
> >>>>>
> >>>>> Here is the output of 'fwcontrol -p'.
> >>>>>
> >>>>> Thanks,
> >>>>>
> >>>>> -Steve
> >>>>>
> >>>>>       
> >>>>>           
> >>>> Let me see what "beta mode" means.
> >>>>
> >>>> Also, can you link me to the manufacturer's web site for the specific 
> >>>> model you have?
> >>>>
> >>>>     
> >>>>         
> >>>>> === base register ===
> >>>>> 0x07 0x85 0xe3 0xe2 0xc4 0x03 0x10 0x00
> >>>>> Physical_ID:1  R:1  CPS:1
> >>>>> RHB:1  IBR:0  Gap_Count:5
> >>>>> Extended:7 Num_Ports:3
> >>>>> PHY_Speed:7 Delay:2
> >>>>> LCtrl:1 C:1 Jitter:0 Pwr_Class:4
> >>>>> WDIE:0 ISBR:0 CTOI:0 CPSI:0 STOI:0 PEI:0 EAA:1 EMC:1
> >>>>> Max_Legacy_SPD:0 BLINK:1 Bridge:0
> >>>>> Page_Select:0 Port_Select0
> >>>>>
> >>>>> === page 0 port 0 ===
> >>>>> 0xf8 0x60 0x3b 0x00 0x00 0x00 0x00 0x00
> >>>>> Astat:3 BStat:3 Ch:1 Con:0 RXOK:0 Dis:0
> >>>>> Negotiated_speed:3 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
> >>>>> DC_connected:0 Max_port_speed:3 LPP:1 Cable_speed:3
> >>>>> Connection_unreliable:0 Beta_mode:0
> >>>>> Port_error:0x0
> >>>>> Loop_disable:0 In_standby:0 Hard_disable:0
> >>>>>
> >>>>> === page 0 port 1 ===
> >>>>> 0xfe 0x60 0x3b 0x08 0x00 0x00 0x00 0x00
> >>>>> Astat:3 BStat:3 Ch:1 Con:1 RXOK:1 Dis:0
> >>>>> Negotiated_speed:3 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
> >>>>> DC_connected:0 Max_port_speed:3 LPP:1 Cable_speed:3
> >>>>> Connection_unreliable:0 Beta_mode:1
> >>>>> Port_error:0x0
> >>>>> Loop_disable:0 In_standby:0 Hard_disable:0
> >>>>>
> >>>>> === page 0 port 2 ===
> >>>>> 0xf8 0x60 0x3b 0x00 0x00 0x00 0x00 0x00
> >>>>> Astat:3 BStat:3 Ch:1 Con:0 RXOK:0 Dis:0
> >>>>> Negotiated_speed:3 PIE:0 Fault:0 Stanby_fault:0 Disscrm:0 B_Only:0
> >>>>> DC_connected:0 Max_port_speed:3 LPP:1 Cable_speed:3
> >>>>> Connection_unreliable:0 Beta_mode:0
> >>>>> Port_error:0x0
> >>>>> Loop_disable:0 In_standby:0 Hard_disable:0
> >>>>>
> >>>>> === page 1 ===
> >>>>> 0x02 0x00 0x08 0x00 0x28 0x83 0x13 0x04
> >>>>> Compliance:2
> >>>>> Vendor_ID:0x080028
> >>>>> Product_ID:0x831304
> >>>>>
> >>>>>
> >>>>>
> >>>>>       
> >>>>>           
> >>>>>> -- 
> >>>>>> Sean Bruno
> >>>>>> MiraLink Corporation
> >>>>>> 6015 NE 80th Ave, Ste 100
> >>>>>> Portland, OR 97218
> >>>>>> Cell 503-358-6832
> >>>>>> Phone 503-621-5143
> >>>>>> Fax 503-621-5199
> >>>>>> MSN: [email protected]
> >>>>>> Google:  [email protected]
> >>>>>>
> >>>>>>         
> >>>>>>             
> >>>> -- 
> >>>> Sean Bruno
> >>>> MiraLink Corporation
> >>>> 6015 NE 80th Ave, Ste 100
> >>>> Portland, OR 97218
> >>>> Cell 503-358-6832
> >>>> Phone 503-621-5143
> >>>> Fax 503-621-5199
> >>>> MSN: [email protected]
> >>>> Google:  [email protected]
> >>>>
> >>>>     
> >>>>         
> >>>   
> >>>       
> >> Thanks.  I _think_ that my local CostCo has them in stock. 
> >>
> >> Sean
> >>
> >> -- 
> >> Sean Bruno
> >> MiraLink Corporation
> >> 6015 NE 80th Ave, Ste 100
> >> Portland, OR 97218
> >> Phone 503-621-5143
> >> Fax 503-621-5199
> >> MSN: [email protected]
> >> Google:  [email protected]
> >>
> >>     
> >
> >   
> Maybe this well give me a clue.  Set a couple of sysctl variables and 
> then send me the output when connecting the hard drive:
> debug.sbp_debug --> 1
> debug.firewire_debug --> 1
> 
> Sean
> 
> 
> -- 
> Sean Bruno
> MiraLink Corporation
> 6015 NE 80th Ave, Ste 100
> Portland, OR 97218
> Phone 503-621-5143
> Fax 503-621-5199
> MSN: [email protected]
> Google:  [email protected]
> 

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-firewire
To unsubscribe, send any mail to "[email protected]"