Re: Western Digital 1TB My Book Studio

Stephen Bader wrote:
> Sean,
>
> I've applied the patch and it still doesn't work. Here is the debug 
> output:
>
> fwohci0: Initiate bus reset
> fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
> fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
> fwohci0: BUS reset
> sbp_post_busreset
> fwohci0: node_id=0xc800ffc1, gen=5, CYCLEMASTER mode
> firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
> fwohci0: fw_set_bus_manager: 1->1 (loop=0)
> firewire0: bus manager 1 (me)
> send phy_config root_node=1 gap_count=5
> fwohci0: start AT DMA status=12
> node0: crom unchanged
> fw_explore: node 2, err = 0
> bus_explore done
> sbp_post_explore (sbp_cold=0)
> sbp_post_explore: EUI:0090a9341b93f349 attached
> target 0 lun 0 found
> target 0 lun 1 found
> sbp_probe_target: detected non sequential access device(64).  skipping
> sbp_probe_target: detected non sequential access device(77).  skipping
>
> It appears as though the patch applied properly, but now it is just 
> skipping and doing nothing.
>
> -Steve
Ha!  That's because I didn't put the correct device type.  Try this patch.

-- 
Sean Bruno
MiraLink Corporation
6015 NE 80th Ave, Ste 100
Portland, OR 97218
Cell 503-358-6832
Phone 503-621-5143
Fax 503-621-5199
MSN: [email protected]
Google:  [email protected]

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-firewire
To unsubscribe, send any mail to "[email protected]"

Index: sbp.c
===================================================================
--- sbp.c	(revision 5540)
+++ sbp.c	(working copy)
@@ -738,6 +738,18 @@
 		sdev = target->luns[i];
 		if (sdev == NULL)
 			continue;
+		/*
+	 	 * if a Firewire device reports some kind
+	 	 * of other device, that is not a drive
+	 	 * then skip it
+	 	 */
+		if (sdev->type != T_DIRECT) {
+SBP_DEBUG(0)
+			printf("%s: detected non sequential access device(%d).  skipping\n",
+				__func__, sdev->type);
+END_DEBUG
+			continue;
+		}
 		if (alive && (sdev->status != SBP_DEV_DEAD)) {
 			if (sdev->path != NULL) {
 				SBP_LOCK(sbp);
@@ -855,7 +867,7 @@
 	/* traverse device list */
 	STAILQ_FOREACH(fwdev, &sbp->fd.fc->devices, link) {
 SBP_DEBUG(0)
-		printf("sbp_post_explore: EUI:%08x%08x ",
+		printf("%s: EUI:%08x%08x ", __func__,
 				fwdev->eui.hi, fwdev->eui.lo);
 		if (fwdev->status != FWDEVATTACHED)
 			printf("not attached, state=%d.\n", fwdev->status);