Re: Strange errors with LSI 9207-8e (LSI SAS2308)
George Kontostanos <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.scsi,gmane.os.freebsd.devel.hardware |
|---|---|
| Message-ID | <CA+dUSyrz_JgeKgKDCTjNRkkavhF0F_AFt_0-W_S00pQNCKxzAQ@mail.gmail.com> |
On Mon, Feb 18, 2013 at 8:15 PM, George Kontostanos <[email protected]> wrote: > On Mon, Feb 18, 2013 at 7:52 PM, Martin Nilsson <[email protected]> wrote: >> On 2013-02-18 18:44, George Kontostanos wrote: >>> >>> Hallo everybody, >>> >>> We are using FreeBSD 9.1-RELEASE with 11 drives WDC WD30EFRX-68AX9N0 >>> (RED 3 TB) in a RAIDz3 connected to an LSI 9207-8e controller with >>> bios 7.29.00.00 and firmware 15.00.00.00 on a X9DRD-7LN4F-JBOD >>> SuperMicro board. The board has an on board controller LSI SAS2308 >>> which is running the same firmware and bios. >>> >>> As soon as we start transferring data to the pool we get the following >>> errors: >>> >>> 31072 SMID 281 terminated ioc 804b scsi 0 state c xfer 0 >>> Feb 17 14:59:25 DLCH010 kernel: (da1:mps0:0:15:0): WRITE(10). CDB: 2a >>> 0 1 54 5a 88 0 1 0 0 length 131072 SMID 407 terminated ioc 804b scsi 0 >>> state c xfer 0 >>> Feb 17 14:59:25 DLCH010 kernel: (da1:mps0:0:15:0): WRITE(10). CDB: 2a >>> 0 1 54 59 88 0 1 0 0 length 131072 SMID 238 terminated ioc 804b scsi 0 >>> state c xfer 0 >>> Feb 17 14:59:25 DLCH010 kernel: (da1:mps0:0:15:0): WRITE(10). CDB: 2a >>> 0 1 54 58 88 0 1 0 0 length 131072 SMID 331 terminated ioc 804b scsi 0 >>> state c xfer 0 >>> Feb 17 14:59:25 DLCH010 kernel: (da1:mps0:0:15:0): WRITE(10). CDB: 2a >>> 0 1 54 57 88 0 1 0 0 length 131072 SMID 443 terminated ioc 804b scsi 0 >>> state c xfer 0 >>> Feb 17 14:59:25 DLCH010 kernel: (da1:mps0:0:15:0): WRITE(10). CDB: 2a >>> 0 1 54 54 a0 0 1 0 0 >>> Feb 17 14:59:25 DLCH010 kernel: (da1:mps0:0:15:0): CAM status: SCSI Status >>> Error >>> Feb 17 14:59:25 DLCH010 kernel: (da1:mps0:0:15:0): SCSI status: Check >>> Condition >>> Feb 17 14:59:25 DLCH010 kernel: (da1:mps0:0:15:0): SCSI sense: UNIT >>> ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred) >>> >>> The errors keep going and going for all drives not just da2. We >>> compiled the latest LSI driver (15) but the errors did not stop: >>> >>> >> Sounds a lot like bad cabling or vibrations in the JBOD chassis. >> What kind of chassis do you use for the drives connected to the -8e card? >> >> WD Red drives does not have RAFF and should not be used in a chassis with >> more than four drives. > > We are using the SUPERMICRO chassis 847e26-RJbod1 > (http://www.supermicro.com/products/chassis/4u/847/SC847E26-RJBOD1.cfm?parts=SHOW) > > I really don't see any vibrations the JBOD is steady and the cabling > has been changed. It appears that the error messages don't display anymore in FreeBSD 9.1-STABLE >> -- >> Martin Nilsson, CEO, Mullet Scandinavia AB, Malmö, SWEDEN >> E-mail: [email protected], Phone: +46-(0)708-59 99 91, Web: www.mullet.se >> >> Our business is well engineered servers optimised for FreeBSD & Linux >> >> _______________________________________________ >> [email protected] mailing list >> http://lists.freebsd.org/mailman/listinfo/freebsd-scsi >> To unsubscribe, send any mail to "[email protected]" > > > > -- > George Kontostanos > --- > http://www.aisecure.net -- George Kontostanos --- http://www.aisecure.net _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-scsi To unsubscribe, send any mail to "[email protected]"