Re: Digium b410p with i4b
Mikael Batard <[email protected]> Thu, 12 Jul 2007 22:32:58 +0200
| Newsgroups | gmane.os.freebsd.devel.isdn |
|---|---|
| Organization | Wan Again |
| Message-ID | <[email protected]> |
On 12.07.2007 19:05, Hans Petter Selasky wrote:
> Hi Mikael!
Hi Hans,
> You need to insert a:
>
> exten => n,xxx,Ringing
>
> when you receive the call(s) from ISDN in your dialplan!
Done, but it doesn't work.
I've got some missed calls again :(
Here's new debug with Ringing added :
# isdndecode -u 10 -i -o -x
=========== isdndecode controller #10 ========== started Thu Jul 12
22:27:46 2007
-- NT->TE - unit:10 --------------- time:12.07 22:27:54.236616
----------------
L1 STATE: F7: Activated
-- NT->TE - unit:10 frame:002397 - time:12.07 22:27:54.236671 -
length:40 ----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 FF 1111111- TEI = 127 = 0x7f
(Broadcast TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 03 000-0011 U-Frame: UI (Unnumbered
Information)
---0---- P/F, Poll = No Immediate Response Required
L3 03 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 04 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 05 2B 0------- Call Reference is sent from call originator
-0101011 Call Reference = 43 = 0x2b
L3 06 05 0------- Message type extension = 0
-0000101 Message type = SETUP
(0x05)
L3 07 A1 1------- Single octet Information element
-0100001 Sending complete
L3 08 04 0------- Variable length Information element
-0000100 IE = bearer capability
L3 09 03 00000011 IE Length = 3 bytes
L3 0A 90 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Coding standard = CCITT
---10000 Capability = 0x10, 3.1 kHz audio
L3 0B 90 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Mode = 0x00, circuit
---10000 Rate = 0x10, 64 kbit/s
L3 0C A3 1------- Extension Bit = 1 (no extension, final
octet)
-01----- Layer 1 identity = 1
---00011 Layer 1 Protocol = 0x03, G.711 a-Law
L3 0D 18 0------- Variable length Information element
-0011000 IE = channel identification
L3 0E 01 00000001 IE Length = 1 bytes
L3 0F 89 1------- Extension Bit = 1 (no extension, final
octet)
-0------ Interface Id present = No
--0----- Interface Type = BRI
---0---- Spare
----1--- Channel is exclusive
-----0-- Channel is not the D-Channel
------01 Channel = B-1
L3 10 1E 0------- Variable length Information element
-0011110 IE = progress indicator
L3 11 02 00000010 IE Length = 2 bytes
L3 12 84 -00----- Coding standard = CCITT
----0100 location = Public network serving remote user
L3 13 83 -0000011 description = Origination address is non-ISDN
L3 14 6C 0------- Variable length Information element
-1101100 IE = calling party number
L3 15 0B 00001011 IE Length = 11 bytes
L3 16 20 0------- Extension Bit = 0 (with extension, octet
follows)
-010---- Type = National number
----0000 Plan = Unknown
(0x0)
L3 17 83 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Presentation = allowed
---000-- Spare
------11 Screening = network provided
L3 18 39 00111001 Number digit = 9
L3 19 35 00110101 Number digit = 5
L3 1A 32 00110010 Number digit = 2
L3 1B 37 00110111 Number digit = 7
L3 1C 36 00110110 Number digit = 6
L3 1D 30 00110000 Number digit = 0
L3 1E 37 00110111 Number digit = 7
L3 1F 35 00110101 Number digit = 5
L3 20 30 00110000 Number digit = 0
L3 21 70 0------- Variable length Information element
-1110000 IE = called party number
L3 22 05 00000101 IE Length = 5 bytes
L3 23 81 1------- Extension Bit = 1 (no extension, final
octet)
-000---- Type = Unknown
----0001 Plan = ISDN (E.164)
(0x1)
L3 24 30 00110000 Number digit = 0
L3 25 39 00111001 Number digit = 9
L3 26 38 00111000 Number digit = 8
L3 27 37 00110111 Number digit = 7
-- NT->TE - unit:10 frame:002398 - time:12.07 22:27:54.236715 -
length:3 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 01 0000000- TEI = 0 = 0x00
(Non-automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 73 011-0011 U-Frame: UA (Unnumbered
Acknowledge)
---1---- P/F, Final = Result of Poll
-- TE->NT - unit:10 frame:002399 - time:12.07 22:27:54.236742 -
length:8 -----
L2 00 FC 111111-- SAPI = 63 (Layer 2
Management)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 FF 1111111- TEI = 127 = 0x7f
(Broadcast TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 03 000-0011 U-Frame: UI (Unnumbered
Information)
---0---- P/F, Poll = No Immediate Response Required
L2 03 0F 00001111 MEI (Management Entity
Identifier)
L2 04 AF 10101111 Ri = 0xaf57 (Reference
number high)
L2 05 57 01010111 Ri (Reference
Number low)
L2 06 01 00000001 TEI Identity message = REQUEST
(0x01)
L2 07 FF 1111111- Ai = 127 (Action
Indicator = )
-------1 Extension Bit = 1 (no extension,
final octet)
-- NT->TE - unit:10 frame:002400 - time:12.07 22:27:54.284661 -
length:8 -----
L2 00 FE 111111-- SAPI = 63 (Layer 2
Management)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 FF 1111111- TEI = 127 = 0x7f
(Broadcast TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 03 000-0011 U-Frame: UI (Unnumbered
Information)
---0---- P/F, Poll = No Immediate Response Required
L2 03 0F 00001111 MEI (Management Entity
Identifier)
L2 04 AF 10101111 Ri = 0xaf57 (Reference
number high)
L2 05 57 01010111 Ri (Reference
Number low)
L2 06 02 00000010 TEI Identity message = ASSIGNED
(0x02)
L2 07 BF 1011111- Ai = 95 (Action
Indicator)
-------1 Extension Bit = 1 (no extension,
final octet)
-- NT->TE - unit:10 frame:002401 - time:12.07 22:27:54.284701 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 01 0000000- TEI = 0 = 0x00
(Non-automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 02 0000001- N(R) = 1 (receive sequence
number)
-------0 P/F, Final = No Result of Poll
-- TE->NT - unit:10 frame:002402 - time:12.07 22:27:54.284728 -
length:3 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 7F 011-1111 U-Frame: SABME (Set Asynchonous
Balanced Mode)
---1---- P/F, Poll = Immediate Response Required
-- TE->NT - unit:10 frame:002403 - time:12.07 22:27:54.284731 -
length:8 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 00 0000000- N(S) = 0 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 00 0000000- N(R) = 0 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 7F 0------- Call Reference is sent from call originator
-1111111 Call Reference = 127 = 0x7f
L3 07 75 0------- Message type extension = 0
-1110101 Message type = STATUS_ENQUIRY
(0x75)
-- TE->NT - unit:10 frame:002404 - time:12.07 22:27:54.284747 -
length:8 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 02 0000001- N(S) = 1 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 01 0000000- N(R) = 0 (receive sequence
number)
-------1 P/F, Poll = Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 7F 0------- Call Reference is sent from call originator
-1111111 Call Reference = 127 = 0x7f
L3 07 75 0------- Message type extension = 0
-1110101 Message type = STATUS_ENQUIRY
(0x75)
-- NT->TE - unit:10 frame:002405 - time:12.07 22:27:54.316663 -
length:3 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 73 011-0011 U-Frame: UA (Unnumbered
Acknowledge)
---1---- P/F, Final = Result of Poll
-- NT->TE - unit:10 frame:002406 - time:12.07 22:27:54.316688 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 02 0000001- N(R) = 1 (receive sequence
number)
-------0 P/F, Final = No Result of Poll
-- NT->TE - unit:10 frame:002407 - time:12.07 22:27:54.348661 -
length:15 ----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 00 0000000- N(S) = 0 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 02 0000001- N(R) = 1 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 FF 1------- Call Reference is sent to call originator
-1111111 Call Reference = 127 = 0x7f
L3 07 7D 0------- Message type extension = 0
-1111101 Message type = STATUS
(0x7d)
L3 08 08 0------- Variable length Information element
-0001000 IE = cause
L3 09 02 00000010 IE Length = 2 bytes
L3 0A 87 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Coding standard = CCITT
---0---- Spare
----0111 Location = ERROR: undefined/reserved
L3 0B 9E 1------- Extension Bit = 1 (no extension, final
octet)
-0011110 Cause = 30: Q.850: response to STATUS ENQUIRY
L3 0C 14 0------- Variable length Information element
-0010100 IE = call state
L3 0D 01 00000001 IE Length = 1 bytes
L3 0E 00 -00----- Coding standard = CCITT
---00000 state = Null
-- NT->TE - unit:10 frame:002408 - time:12.07 22:27:54.348691 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 05 0000010- N(R) = 2 (receive sequence
number)
-------1 P/F, Final = Result of Poll
-- TE->NT - unit:10 frame:002409 - time:12.07 22:27:54.348721 -
length:8 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 04 0000010- N(S) = 2 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 02 0000001- N(R) = 1 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 AB 1------- Call Reference is sent to call originator
-0101011 Call Reference = 43 = 0x2b
L3 07 02 0------- Message type extension = 0
-0000010 Message type = CALL_PROCEEDING
(0x02)
-- TE->NT - unit:10 frame:002410 - time:12.07 22:27:54.348724 -
length:8 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 06 0000011- N(S) = 3 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 03 0000001- N(R) = 1 (receive sequence
number)
-------1 P/F, Poll = Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 AB 1------- Call Reference is sent to call originator
-0101011 Call Reference = 43 = 0x2b
L3 07 07 0------- Message type extension = 0
-0000111 Message type = CONNECT
(0x07)
-- NT->TE - unit:10 frame:002411 - time:12.07 22:27:54.380663 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 06 0000011- N(R) = 3 (receive sequence
number)
-------0 P/F, Final = No Result of Poll
-- NT->TE - unit:10 frame:002412 - time:12.07 22:27:54.380694 -
length:15 ----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 02 0000001- N(S) = 1 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 06 0000011- N(R) = 3 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 FF 1------- Call Reference is sent to call originator
-1111111 Call Reference = 127 = 0x7f
L3 07 7D 0------- Message type extension = 0
-1111101 Message type = STATUS
(0x7d)
L3 08 08 0------- Variable length Information element
-0001000 IE = cause
L3 09 02 00000010 IE Length = 2 bytes
L3 0A 87 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Coding standard = CCITT
---0---- Spare
----0111 Location = ERROR: undefined/reserved
L3 0B 9E 1------- Extension Bit = 1 (no extension, final
octet)
-0011110 Cause = 30: Q.850: response to STATUS ENQUIRY
L3 0C 14 0------- Variable length Information element
-0010100 IE = call state
L3 0D 01 00000001 IE Length = 1 bytes
L3 0E 00 -00----- Coding standard = CCITT
---00000 state = Null
-- TE->NT - unit:10 frame:002413 - time:12.07 22:27:54.380724 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 04 0000010- N(R) = 2 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
-- NT->TE - unit:10 frame:002414 - time:12.07 22:27:54.412661 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 09 0000100- N(R) = 4 (receive sequence
number)
-------1 P/F, Final = Result of Poll
-- NT->TE - unit:10 frame:002415 - time:12.07 22:27:54.412692 -
length:12 ----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 04 0000010- N(S) = 2 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 08 0000100- N(R) = 4 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 2B 0------- Call Reference is sent from call originator
-0101011 Call Reference = 43 = 0x2b
L3 07 5A 0------- Message type extension = 0
-1011010 Message type = RELEASE_COMPLETE
(0x5a)
L3 08 08 0------- Variable length Information element
-0001000 IE = cause
L3 09 02 00000010 IE Length = 2 bytes
L3 0A 87 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Coding standard = CCITT
---0---- Spare
----0111 Location = ERROR: undefined/reserved
L3 0B D1 1------- Extension Bit = 1 (no extension, final
octet)
-1010001 Cause = 81: Q.850: invalid call reference value
-- TE->NT - unit:10 frame:002416 - time:12.07 22:27:54.412733 -
length:12 ----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 08 0000100- N(S) = 4 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 07 0000011- N(R) = 3 (receive sequence
number)
-------1 P/F, Poll = Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 AB 1------- Call Reference is sent to call originator
-0101011 Call Reference = 43 = 0x2b
L3 07 5A 0------- Message type extension = 0
-1011010 Message type = RELEASE_COMPLETE
(0x5a)
L3 08 08 0------- Variable length Information element
-0001000 IE = cause
L3 09 02 00000010 IE Length = 2 bytes
L3 0A 80 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Coding standard = CCITT
---0---- Spare
----0000 Location = User
L3 0B E6 1------- Extension Bit = 1 (no extension, final
octet)
-1100110 Cause = 102: Q.850: recovery on timer expiry
-- NT->TE - unit:10 frame:002417 - time:12.07 22:27:54.444660 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 01 0000000- TEI = 0 = 0x00
(Non-automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 04 0000010- N(R) = 2 (receive sequence
number)
-------0 P/F, Final = No Result of Poll
-- NT->TE - unit:10 frame:002418 - time:12.07 22:27:54.444686 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 0B 0000101- N(R) = 5 (receive sequence
number)
-------1 P/F, Final = Result of Poll
-- NT->TE - unit:10 frame:002419 - time:12.07 22:27:54.476658 -
length:12 ----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 06 0000011- N(S) = 3 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 0A 0000101- N(R) = 5 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 2B 0------- Call Reference is sent from call originator
-0101011 Call Reference = 43 = 0x2b
L3 07 5A 0------- Message type extension = 0
-1011010 Message type = RELEASE_COMPLETE
(0x5a)
L3 08 08 0------- Variable length Information element
-0001000 IE = cause
L3 09 02 00000010 IE Length = 2 bytes
L3 0A 87 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Coding standard = CCITT
---0---- Spare
----0111 Location = ERROR: undefined/reserved
L3 0B D1 1------- Extension Bit = 1 (no extension, final
octet)
-1010001 Cause = 81: Q.850: invalid call reference value
-- TE->NT - unit:10 frame:002420 - time:12.07 22:27:54.476696 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 08 0000100- N(R) = 4 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
-- NT->TE - unit:10 frame:002421 - time:12.07 22:27:56.460636 -
length:3 -----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 53 010-0011 U-Frame: DISC
(Disconnect)
---1---- P/F, Poll = Immediate Response Required
-- TE->NT - unit:10 frame:002422 - time:12.07 22:27:56.460671 -
length:3 -----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 BF 1011111- TEI = 95 = 0x5f
(Automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 73 011-0011 U-Frame: UA (Unnumbered
Acknowledge)
---1---- P/F, Final = Result of Poll
-- NT->TE - unit:10 frame:002423 - time:12.07 22:27:56.524636 -
length:8 -----
L2 00 FE 111111-- SAPI = 63 (Layer 2
Management)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 FF 1111111- TEI = 127 = 0x7f
(Broadcast TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 03 000-0011 U-Frame: UI (Unnumbered
Information)
---0---- P/F, Poll = No Immediate Response Required
L2 03 0F 00001111 MEI (Management Entity
Identifier)
L2 04 00 00000000 Ri = 0x0000 (Reference
number high)
L2 05 00 00000000 Ri (Reference
Number low)
L2 06 04 00000100 TEI Identity message = CHECK REQUEST
(0x04)
L2 07 FF 1111111- Ai = 127 (Action
Indicator = )
-------1 Extension Bit = 1 (no extension,
final octet)
-- NT->TE - unit:10 frame:002424 - time:12.07 22:27:57.548631 -
length:8 -----
L2 00 FE 111111-- SAPI = 63 (Layer 2
Management)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 FF 1111111- TEI = 127 = 0x7f
(Broadcast TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 03 000-0011 U-Frame: UI (Unnumbered
Information)
---0---- P/F, Poll = No Immediate Response Required
L2 03 0F 00001111 MEI (Management Entity
Identifier)
L2 04 00 00000000 Ri = 0x0000 (Reference
number high)
L2 05 00 00000000 Ri (Reference
Number low)
L2 06 04 00000100 TEI Identity message = CHECK REQUEST
(0x04)
L2 07 BF 1011111- Ai = 95 (Action
Indicator)
-------1 Extension Bit = 1 (no extension,
final octet)
-- NT->TE - unit:10 frame:002425 - time:12.07 22:27:58.572624 -
length:8 -----
L2 00 FE 111111-- SAPI = 63 (Layer 2
Management)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 FF 1111111- TEI = 127 = 0x7f
(Broadcast TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 03 000-0011 U-Frame: UI (Unnumbered
Information)
---0---- P/F, Poll = No Immediate Response Required
L2 03 0F 00001111 MEI (Management Entity
Identifier)
L2 04 00 00000000 Ri = 0x0000 (Reference
number high)
L2 05 00 00000000 Ri (Reference
Number low)
L2 06 04 00000100 TEI Identity message = CHECK REQUEST
(0x04)
L2 07 BF 1011111- Ai = 95 (Action
Indicator)
-------1 Extension Bit = 1 (no extension,
final octet)
-- NT->TE - unit:10 frame:002426 - time:12.07 22:27:58.988627 -
length:12 ----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 01 0000000- TEI = 0 = 0x00
(Non-automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 00 0000000- N(S) = 0 (send sequence
number)
-------0 I-Frame: Information transfer
L2 03 04 0000010- N(R) = 2 (receive sequence
number)
-------0 P/F, Poll = No Immediate Response Required
L3 04 08 00001000 Protocol = Q.931/I.451/DSS1
(0x08)
L3 05 01 0000---- Call Reference
----0001 Call Reference length is 1 byte
L3 06 2B 0------- Call Reference is sent from call originator
-0101011 Call Reference = 43 = 0x2b
L3 07 4D 0------- Message type extension = 0
-1001101 Message type = RELEASE
(0x4d)
L3 08 08 0------- Variable length Information element
-0001000 IE = cause
L3 09 02 00000010 IE Length = 2 bytes
L3 0A 87 1------- Extension Bit = 1 (no extension, final
octet)
-00----- Coding standard = CCITT
---0---- Spare
----0111 Location = ERROR: undefined/reserved
L3 0B 90 1------- Extension Bit = 1 (no extension, final
octet)
-0010000 Cause = 16: Q.850: normal call clearing
-- NT->TE - unit:10 frame:002427 - time:12.07 22:27:59.052620 -
length:4 -----
L2 00 00 000000-- SAPI = 0 (Call
Control)
------0- C/R = Response
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 01 0000000- TEI = 0 = 0x00
(Non-automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 01 00000001 S-Frame: RR (Receiver
Ready)
L2 03 06 0000011- N(R) = 3 (receive sequence
number)
-------0 P/F, Final = No Result of Poll
-- NT->TE - unit:10 frame:002428 - time:12.07 22:27:59.596619 -
length:8 -----
L2 00 FE 111111-- SAPI = 63 (Layer 2
Management)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 FF 1111111- TEI = 127 = 0x7f
(Broadcast TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 03 000-0011 U-Frame: UI (Unnumbered
Information)
---0---- P/F, Poll = No Immediate Response Required
L2 03 0F 00001111 MEI (Management Entity
Identifier)
L2 04 00 00000000 Ri = 0x0000 (Reference
number high)
L2 05 00 00000000 Ri (Reference
Number low)
L2 06 06 00000110 TEI Identity message = REMOVE
(0x06)
L2 07 BF 1011111- Ai = 95 (Action
Indicator)
-------1 Extension Bit = 1 (no extension,
final octet)
-- NT->TE - unit:10 frame:002429 - time:12.07 22:27:59.596643 -
length:8 -----
L2 00 FE 111111-- SAPI = 63 (Layer 2
Management)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 FF 1111111- TEI = 127 = 0x7f
(Broadcast TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 03 000-0011 U-Frame: UI (Unnumbered
Information)
---0---- P/F, Poll = No Immediate Response Required
L2 03 0F 00001111 MEI (Management Entity
Identifier)
L2 04 00 00000000 Ri = 0x0000 (Reference
number high)
L2 05 00 00000000 Ri (Reference
Number low)
L2 06 06 00000110 TEI Identity message = REMOVE
(0x06)
L2 07 BF 1011111- Ai = 95 (Action
Indicator)
-------1 Extension Bit = 1 (no extension,
final octet)
-- NT->TE - unit:10 frame:002430 - time:12.07 22:28:01.068611 -
length:3 -----
L2 00 02 000000-- SAPI = 0 (Call
Control)
------1- C/R = Command
-------0 Extension Bit = 0 (with extension, octet
follows)
L2 01 01 0000000- TEI = 0 = 0x00
(Non-automatic TEI)
-------1 Extension Bit = 1 (no extension,
final octet)
L2 02 53 010-0011 U-Frame: DISC
(Disconnect)
---1---- P/F, Poll = Immediate Response Required
-- NT->TE - unit:10 --------------- time:12.07 22:28:04.364553
----------------
L1 STATE: F3: Deactivated
> Actually Asterisk should do that, so maybe there is a bug in Asterisk. You can
> see on the trace that there is only:
>
> -- TE->NT - unit:08 frame:002265 - time:12.07 18:22:41.132110 -
>
> CALL_PROCEEDING
>
> from the TE side, and this state will timeout after 10-20 seconds per ISDN
> specification. That is most likely what happens. The "ringing" state on the
> other hand will timeout after approximately 2 minutes under I4B.
I'm using asterisk 1.2.17 from ports and freepbx 2.1.
Regards
--
Mikael Batard
Wan Again
12 Route de l'Isle
84510 Caumont sur Durance
Tel: +33 (0)4 90 01 26 86
Fax: +33 (0)4 90 23 10 58
http://www.wanagain.fr/
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-isdn
To unsubscribe, send any mail to "[email protected]"