dell Inspiron 8600c halts sometimes during bootup

Hi,

I'm using the new freebsd 5.4

Sometimes my DELL inspiron 8600c hangs when the dvd&cdrecorder drive is 
displayed during the boot process.

Acpi and udma is enabled, I got a similiar problem in 5.3

No idea, what I could try....

Any ideas ?

Here's the output of dmesg:

Greetings and thanks in advance,

Raphael

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.4-RELEASE #0: Sun May  8 10:21:06 UTC 2005
    [email protected]:/usr/obj/usr/src/sys/GENERIC
module_register: module pci/bfe already exists!
Module pci/bfe failed to register: 17
module_register: module bfe/miibus already exists!
Module bfe/miibus failed to register: 17
module_register: module pci/bge already exists!
Module pci/bge failed to register: 17
module_register: module bge/miibus already exists!
Module bge/miibus failed to register: 17
module_register: module uhub/ugen already exists!
Module uhub/ugen failed to register: 17
module_register: module uhub/ums already exists!
Module uhub/ums failed to register: 17
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1.60GHz (1594.83-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6d6  Stepping = 6
  
Features=0xafe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
real memory  = 536535040 (511 MB)
avail memory = 515354624 (491 MB)
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL CPi R  > on motherboard
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU (4 Cx states)> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI link \\_SB_.PCI0.LNKB has invalid initial irq 11, ignoring
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82855 host to AGP bridge> mem 0xe0000000-0xe7ffffff at 
device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f 
irq 11 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f 
irq 11 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f 
irq 11 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xfaffe000-0xfaffffff irq 11 
at device 0.0 on pci2
miibus0: <MII bus> on bfe0
bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0
bmtphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bfe0: Ethernet address: 00:0f:1f:1d:8a:84
cbb0: <TI4510 PCI-CardBus Bridge> at device 1.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem 
0xfaff8000-0xfaffbfff,0xfaffd800-0xfaffdfff irq 11 at device 1.1 on pci2
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 39:4f:c0:00:05:d4:98:30
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 3a:4f:c0:d4:98:30
fwe0: Ethernet address: 3a:4f:c0:d4:98:30
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ipw0: <Intel(R) PRO/Wireless 2100 MiniPCI> mem 0xfaffc000-0xfaffcfff irq 
5 at device 3.0 on pci2
ipw0: Ethernet address: 00:0c:f1:3b:2e:01
ipw0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 
0xbfa0-0xbfaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pcm0: <Intel ICH4 (82801DB)> port 0xbc40-0xbc7f,0xb800-0xb8ff mem 
0xf4fff400-0xf4fff4ff,0xf4fff800-0xf4fff9ff irq 5 at device 31.5 on pci0
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
Timecounter "TSC" frequency 1594833718 Hz quality 800
Timecounters tick every 10.000 msec
ad0: 57231MB <FUJITSU MHT2060AT PL/0022> [116280/16/63] at ata0-master 
UDMA100
acd0: CDRW <NEC DVD+RW ND-5100A/10AC> at ata1-master UDMA33
Mounting root from ufs:/dev/ad0s1a
WARNING: driver "vmmon" used unreserved major device number 200
vmmon: Module vmmon: registered with major=200 minor=0 tag=$Name: 
build-570 (3.2.x mvm) $
vmmon: Module vmmon: initialized
Enhanced Speedstep running at 1600 MHz
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"