Re: Resume with ACPI doesn't work on ThinkPad R50e

Hi again.

Actually setting hw.syscons.sc_no_suspend_vtswitch=1 seems to make resume not work.
hw.acpi.reset_video=0 is the only needed value. Then it's all fine.
The strange thing is setting hw.syscons.sc_no_suspend_vtswitch=1  manually with sysctl after the system has booted does not seem to have any effect.
It only disables proper functionality of resume after reboot.

Cheers,
Marcin.

On Thu, 9 Jun 2005 00:23:24 +0200
Marcin Jessa <[email protected]> wrote:

> Hi Kevin, guys.
> 
> Thanks a lot, that helped!
> Everything comes back after resume without any problem. 
> Network (iwi and fx drivers), USB...
> Even X is fine and I do not need to switch to console to bring it back.
> I tried suspend/resume 3 times and it worked like a charm each and every time.
> 
> I added acpi_video_load="YES" to loader.conf
> and 
> hw.acpi.reset_video=0
> hw.syscons.sc_no_suspend_vtswitch=1
> to sysctl.conf
> 
> I noticed after resume dmesg spits out:
> 
> acpi: suspend request ignored (not ready yet)
> wakeup from sleeping state (slept 00:00:19)
> 
> Now even powerd works great automatically adjusting the speed of my CPU when idle on battery.
> 
> The only thing that does not work properly is when hw.acpi.lid_switch_state=S3.
> It goes to sleep mode when I close the lid but X restarts after resume. I can live with that tho.
> 
> 
> Thanks again Kevin, you made my day!
> 
>  
> 
> On Wed, 08 Jun 2005 14:47:26 -0700
> "Kevin Oberman" <[email protected]> wrote:
> 
> > > Date: Wed, 8 Jun 2005 23:17:40 +0200
> > > From: Marcin Jessa <[email protected]>
> > > Sender: [email protected]
> > > 
> > > Hi.
> > > 
> > > I've Thinkpad R50e and I am struggeling to make resume work on it.
> > > I'm on FreeBSD 6.0-CURRENT #2: Wed Jun  8 21:12:11 CEST 2005  (built on sources from a couple of hours ago).
> > > I am able to change the speed of CPU and put the laptop in sleep mode with acpiconf -s 3 (S1, S2 and S3 are supported).
> > > The problem is it never manages to fully wake up from the sleep mode. 
> > > I tried with and without X running with the same result. 
> > > It wakes up, I can hear the drives spin, the screen is turned on but the laptop is still frozen. 
> > > The keayboard is unaccessible.
> > > I dont have apm enabled in the kernel.
> > > Those are the values in my sysctl.conf:
> > > hw.pci.do_powerstate=1
> > > hw.acpi.lid_switch_state=S3
> > > hw.acpi.standby_state=S1
> > > hw.acpi.suspend_state=S3
> > > hw.acpi.sleep_button_state=S3
> > > vfs.usermount=1
> > > hw.acpi.sleep_delay=3
> > > 
> > > device.hints has hint.apm.0.disabled="0"
> > > 
> > > In the dmesg I can also see many occurances of
> > > ichss0: transition to 1 failed
> > > I think that begun after I added device cpufreq to my kernel config.
> > > 
> > > I also followed http://www.iosn.net/Members/kaeru/articles/freebsd/x40/index_html but with no luck.
> > > 
> > > Any ideas how to make resume work?
> > 
> > Just some suggestions that might (or might not) help.
> > 
> > Play with hw.acpi.reset_video and hw.syscons.sc_no_suspend_vtswitch. You
> > may find that you need the jhb acpi_video_dpms patch.
> > 
> > I have the following /boot/loader.conf on my T30:
> > cpufreq_load="YES"
> > vesa_load="YES"
> > snd_ich_load="YES"
> > acpi_video_load="YES"
> > acpi_ibm_load="YES" (This is NOT required for resume, but it is nice for
> >                      a few things. It is the recently posted test
> >                      version and I don't think it's been committed.)
> > 
> > I have the following in my /etc/sysctl.conf on my T30:
> > hw.acpi.reset_video=0
> > hw.syscons.sc_no_suspend_vtswitch=1
> > hw.acpi.lid_switch_state=NONE
> > hw.pci.do_powerstate=1
> > 
> > I do notice that I need to switch from my X display to a vty and back
> > after a resume to get the display back. (CTRL-ALT-F1, ALT-F9)
> > The SpeedStep errors are troubling. I have not seen any other reports of
> > this.
> > -- 
> > R. Kevin Oberman, Network Engineer
> > Energy Sciences Network (ESnet)
> > Ernest O. Lawrence Berkeley National Laboratory (Berkeley Lab)
> > E-mail: [email protected]			Phone: +1 510 486-8634
> _______________________________________________
> [email protected] mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "[email protected]"
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "[email protected]"