acpi_perf error, powerd exiting

Stefan Farfeleder <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile
Message-ID <[email protected]> 
Hi,

on my ThinkPad R32 (dmesg attached), acpi_perf reports the following
error at times, usually after a period of inactivity:

acpi_perf0: Px transition to 1200 failed
acpi_perf0: set freq failed, err 6

This causes powerd to terminate.  It seems to be a temporary error,
because if I restart powerd, it works again.  Should powerd be more
fault-tolerant, is this an acpi_perf bug or my hardware broken?

I've also attached sysctl dev.cpu and hw.acpi.

Stefan

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"
sysctl.txt (text/plain, 1.4 KB) 
dev.cpu.0.%desc: ACPI CPU
dev.cpu.0.%driver: cpu
dev.cpu.0.%location: handle=\_PR_.CPU_
dev.cpu.0.%pnpinfo: _HID=none _UID=0
dev.cpu.0.%parent: acpi0
dev.cpu.0.freq: 2000
dev.cpu.0.freq_levels: 2000/0 1750/0 1500/0 1250/0 1200/0 1050/0 1000/0 900/0 750/0 600/0 500/0 450/0 300/0 250/0 150/0
hw.acpi.supported_sleep_state: S3 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S3
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: S3
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 0
hw.acpi.verbose: 0
hw.acpi.reset_video: 1
hw.acpi.cpu.cx_supported: C1/0 C2/1 C3/85
hw.acpi.cpu.cx_lowest: C1
hw.acpi.cpu.cx_usage: 100.00% 0.00% 0.00%
hw.acpi.thermal.min_runtime: 0
hw.acpi.thermal.polling_rate: 10
hw.acpi.thermal.tz0.temperature: 62.0C
hw.acpi.thermal.tz0.active: -1
hw.acpi.thermal.tz0.passive_cooling: 0
hw.acpi.thermal.tz0.thermal_flags: 0
hw.acpi.thermal.tz0._PSV: 76.5C
hw.acpi.thermal.tz0._HOT: -1
hw.acpi.thermal.tz0._CRT: 78.0C
hw.acpi.thermal.tz0._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
hw.acpi.thermal.tz1.temperature: 49.8C
hw.acpi.thermal.tz1.active: -1
hw.acpi.thermal.tz1.passive_cooling: 0
hw.acpi.thermal.tz1.thermal_flags: 0
hw.acpi.thermal.tz1._PSV: -1
hw.acpi.thermal.tz1._HOT: -1
hw.acpi.thermal.tz1._CRT: 50.0C
hw.acpi.thermal.tz1._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
hw.acpi.battery.life: 98
hw.acpi.battery.time: -1
hw.acpi.battery.state: 0
hw.acpi.battery.units: 2
hw.acpi.battery.info_expire: 5
hw.acpi.acline: 1
dmesg.txt (text/plain, 4.2 KB) 
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 7.0-CURRENT #58: Thu Aug  4 18:17:40 CEST 2005
    [email protected]:/usr/home/stefan/freebsd/obj/usr/home/stefan/freebsd/src/sys/WOMBAT
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz (1999.78-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7
  Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x400<CNTX-ID>
real memory  = 804716544 (767 MB)
avail memory = 778219520 (742 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <IBM TP-1M> on motherboard
acpi_ec0: <Embedded Controller: GPE 0x1c, ECDT> port 0x62,0x66 on acpi0
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 3 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 11 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 5 on acpi0
pci_link4: <ACPI PCI Link LNKE> irq 11 on acpi0
pci_link5: <ACPI PCI Link LNKF> on acpi0
pci_link6: <ACPI PCI Link LNKG> on acpi0
pci_link7: <ACPI PCI Link LNKH> on acpi0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pci0: <serial bus, USB> at device 29.0 (no driver attached)
pci0: <serial bus, USB> at device 29.1 (no driver attached)
pci0: <serial bus, USB> at device 29.2 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
wi0: <Intersil Prism2.5> mem 0xf8000000-0xf8000fff irq 11 at device 7.0 on pci2
wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.1), Station (1.7.4)
wi0: Ethernet address: 00:20:e0:8f:fb:05
pci2: <network, ethernet> at device 8.0 (no driver attached)
pci2: <bridge, PCI-CardBus> at device 9.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm0: <Intel ICH3 (82801CA)> port 0x1c00-0x1cff,0x18c0-0x18ff irq 3 at device 31.5 on pci0
pcm0: [GIANT-LOCKED]
pcm0: <Analog Devices AD1881A AC97 Codec>
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
ppc0: <Standard parallel printer port> port 0x3bc-0x3be irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xd0000-0xd17ff,0xdc000-0xdffff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1999784340 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 28615MB <IC25N030ATCS04 0 CA3OA71A> at ata0-master UDMA100
acd0: DVDROM <HL-DT-STDVD-ROM GDR8081N/0012> at ata1-master UDMA33
Trying to mount root from ufs:/dev/ad0s3a
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.