Re: WG511T dhcp problem on Freebsd 5.4

Hi,

I am using the WG511T with really great results but on FreeBSD 6Beta5,
all I did was add

ifconfig_ath0="DHCP"
ifconfig_ath0="ssid default DHCP"

to /etc/rc.conf

Hope that helps.

Roger

On 9/29/05, Dennis Binder <[email protected]> wrote:
> hello,
>
> i'm trying to get a wlan card WG511T from netgear to work
> and connect to the internet via an accesspoint.
> The accesspoint has an SSID= "WLAN" and provides DHCP.
>
> dmesg bings up the following:
> ath0: <Atheros 5212> mem 0x88000000-0x8800ffff irq 9 at device 0.0 on
> cardbus0
> ath0: mac 5.9 phy 4.3 5ghz radio 4.6
> ath0: Ethernet address: 00:0f:b5:67:1b:4f
> ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps
> 36Mbps 48Mbps 54Mbps
>
> my /etc/rc.conf  looks like this:
> removable_interfaces="ath0 ep0"
> ifconfig_ath0="NO"
>
> my /etc/start_if.ath0 is empty. After plugging the card "ifconfig ath0"
> prints this:
> ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
>     ether 00:0f:b5:67:1b:4f
>     media: IEEE 802.11 Wireless Ethernet autoselect
>     status: no carrier
>     ssid ""
>     channel -1 authmode OPEN powersavemode OFF powersavesleep 100
>     rtsthreshold 2312 protmode CTS
>     wepmode OFF weptxkey 1
>
> after this I want to manually connect to the internet.
> I try
> # ifconfig ath0 ssid WLAN
> # ifconfig ath0
> ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>     inet6 fe80::20f:b5ff:fe67:1b4f%ath0 prefixlen 64 scopeid 0x4
>     inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
>     ether 00:0f:b5:67:1b:4f
>     media: IEEE 802.11 Wireless Ethernet autoselect (DS/1Mbps)
>     status: no carrier
>     ssid WLAN 1:WLAN
>     channel -1 authmode OPEN powersavemode OFF powersavesleep 100
>     rtsthreshold 2312 protmode CTS
>     wepmode OFF weptxkey 1
>
> After running "dhclient ath0" the netgear-card finds the accesspoint ( both
> leds blinking simultanously).
> "ifconfig ath0" prints "status: active" but the inet-address remains
> 0.0.0.0.
>
> How can I assign the card a valid ip-address via dhcp ?
> Or what is wrong in my setup ?
> My second interface fxp0 has no problems getting valid
> ip-address via dhcp.
>
> Any tips are very welcome.
>
> Dennis Binder
>
>
>
> --
> GMX DSL = Maximale Leistung zum minimalen Preis!
> 2000 MB nur 2,99, Flatrate ab 4,99 Euro/Monat: http://www.gmx.net/de/go/dsl
> _______________________________________________
> [email protected] mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
> To unsubscribe, send any mail to "[email protected]"
>
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"