pccard.conf entry for SMC ethernet card

I picked up an SMC "EZ Card 10/100" 'cause it was cheap and I was tired of dealing with the dongle on my trusty old Linksys combo card, but I can't remember how to build a pccard.conf entry from the dumpcis values. Can someone remind me?

 Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
    000:  00 00 ff
	Common memory device information:
		Device number 1, type No device, WPS = OFF
		Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 4
    000:  67 5a 08 ff
	Attribute memory device information:
		Device number 1, type SRAM, WPS = OFF
		Speed = 5.0 x 100 ns, Memory block size = 512b, 2 units
Tuple #3, code = 0x1d (Other conditions for attribute memory), length = 5
    000:  01 67 5a 08 ff
	(MWAIT)
Tuple #4, code = 0x15 (Version 1 info), length = 80
    000:  05 00 53 4d 43 00 53 4d 43 32 36 33 32 57 00 56
    010:  65 72 73 69 6f 6e 20 30 31 2e 30 32 00 00 00 00
    020:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    030:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    040:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff
	Version = 5.0, Manuf = [SMC], card vers = [SMC2632W]
	Addit. info = [Version 01.02],[]
Tuple #5, code = 0x20 (Manufacturer ID), length = 4
    000:  56 01 02 00
	PCMCIA ID = 0x156, OEM ID = 0x2
Tuple #6, code = 0x21 (Functional ID), length = 2
    000:  06 00
	Network/LAN adapter
Tuple #7, code = 0x22 (Functional EXT), length = 2
    000:  01 07
	Network technology: Wireless
Tuple #8, code = 0x22 (Functional EXT), length = 5
    000:  02 40 42 0f 00
	Network speed: 1 Mb/sec
Tuple #9, code = 0x22 (Functional EXT), length = 5
    000:  02 80 84 1e 00
	Network speed: 2 Mb/sec
Tuple #10, code = 0x22 (Functional EXT), length = 5
    000:  02 60 ec 53 00
	Network speed: 5 Mb/sec
Tuple #11, code = 0x22 (Functional EXT), length = 5
    000:  02 c0 d8 a7 00
	Network speed: 11 Mb/sec
Tuple #12, code = 0x22 (Functional EXT), length = 2
    000:  03 07
	Network media: 2.4 GHz
Tuple #13, code = 0x22 (Functional EXT), length = 8
    000:  04 06 00 e0 29 9e 5a fe
	Network node ID: 00 e0 29 9e 5a fe
Tuple #14, code = 0x22 (Functional EXT), length = 2
    000:  05 01
	Network connector: closed connector standard
Tuple #15, code = 0x1a (Configuration map), length = 7
    000:  03 01 e0 03 00 00 01
	Reg len = 4, config register addr = 0x3e0, last config = 0x1
	Registers: X------- 
Tuple #16, code = 0x1b (Configuration entry), length = 15
    000:  c1 01 19 76 c5 4b d5 19 36 36 05 46 7f ff ff
	Config index = 0x1(default)
	Interface byte = 0x1 (I/O)
	Vcc pwr:
		Minimum operating supply voltage: 4 x 1V, ext = 0x4b
		Maximum operating supply voltage: 5 x 1V, ext = 0x19
		Max current average over 1 second: 3 x 100mA
		Max current average over 10 ms: 3 x 100mA
		Power down supply current: 1 x 10mA
	Card decodes 6 address lines, limited 8/16 Bit I/O
		IRQ modes: Level, Pulse
		IRQs:  NMI IOCK BERR VEND 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Tuple #17, code = 0xff (Terminator), length = 0

...arun



To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message