iwi0 in 6_1-PRELEASE doesn't seem to work anymore

Hi,


cat /etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=wheel
network={
        ssid="theAPssid"
        scan_ssid=1
        key_mgmt=WPA-PSK
#        pairwise=TKIP
#        group=TKIP
        psk="123456789012345678"
}


lbe8010# wpa_supplicant -d -i iwi0 -c /etc/wpa_supplicant.conf
Initializing interface 'iwi0' conf '/etc/wpa_supplicant.conf' driver 
'default'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0 (from group name 'wheel')
Priority group 0
   id=0 ssid='theAPssid'
Initializing interface (2) 'iwi0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:0e:35:28:4e:18
wpa_driver_bsd_set_wpa: enabled=1
wpa_driver_bsd_set_wpa_internal: wpa=3 privacy=1
wpa_driver_bsd_del_key: keyidx=0
wpa_driver_bsd_del_key: keyidx=1
wpa_driver_bsd_del_key: keyidx=2
wpa_driver_bsd_del_key: keyidx=3
wpa_driver_bsd_set_countermeasures: enabled=0
wpa_driver_bsd_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=11):
(here the correct ssid it found)
Received 0 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
0: 00:12:17:71:01:dc ssid='theAppssid' wpa_ie_len=26 rsn_ie_len=0
   selected
Trying to associate with 00:12:17:71:01:dc (SSID='theAppssid' freq=2462 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 
01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_bsd_set_drop_unencrypted: enabled=1
wpa_driver_bsd_associate: ssid 'theAPssid' wpa ie len 24 pairwise 2 
group 2 key mgmt 1
wpa_driver_bsd_associate: set PRIVACY 1
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Received 0 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
.....


What is the problem?
It worked before (with 6.0, and before I updated the firmware of the AP 
from something ancient to the latest release...).
The AP in question is a Linksys WAP54G v.2.




Rainer
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"