Problems getting my pcmcia-card to work

Hi all, I am desperately trying to get my pccard to work together with FreeBSD
6.1. With all debug mechanisms enabled, this is what I see in the dmesg:

cbb0: <RF5C475 PCI-CardBus Bridge> irq 23 at device 11.0 on pci2
pcib2: cbb0 requested memory range 0xeb000000-0xed7fffff: good
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xeb001000
cbb0: Found memory at eb001000
cbb0: Secondary bus is 0
cbb0: Setting primary bus to 2
cbb0: Secondary bus set to 3 subbus 4
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
ioapic0: routing intpin 23 (PCI IRQ 23) to vector 50
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
  0x00: 0x04751180 0x02100007 0x06070081 0x00022000 
  0x10: 0xeb001000 0x020000dc 0x20040302 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x07000117 
  0x40: 0x00000000 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x00000001 0x00000000 0x04630463 0x00000000 
  0x90: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xa0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0xfe0a0001 
  0xe0: 0x24c04000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
...
Status is 0x30000410
cbb0: card inserted: event=0x00000000, state=30000410
pccard0: chip_socket_enable
cbb_pcic_socket_enable:
cbb0: cbb_power: 5V
pccard0: read_cis
pcib2: pccard0 requested memory range 0xeb000000-0xed7fffff: good
cis mem map 0xe52a7000 (resource: 0xeb010000)
pccard0: CIS tuple chain:
CISTPL_END
 ff
cis mem map e52a7000
CISTPL_LINKTARGET expected, code ff observed
pccard0: check_cis_quirks
pccard0: Card has no functions!
cbb0: PC Card card activation failed

There are all the information dmesg hands me out ... somebody please, please
help me as I am completely lost on this issue ...

-- 
  .''`.   Martin Loschwitz           Debian GNU/Linux developer
 : :'  :  [email protected]        [email protected]
 `. `'`   http://www.madkiss.org/    people.debian.org/~madkiss/
   `-     Use Debian GNU/Linux 3.1!  See http://www.debian.org/

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (Darwin)

iD8DBQFEZnTLHPo+jNcUXjARAsYtAJ9qETqOdDZVwSRxeXX/HRB0N/D2UACdFQ3T
g0gV5oFEXA/U51fxCI3SiSU=
=QI9Q
-----END PGP SIGNATURE-----