Broadcom bcmwl5 NDIS driver and Dell D610
Colin Faber <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
Hello Folks,
I'm having trouble getting my Dell D610 to recognize my Broadcom/Dell
miniPCI b/g wireless card.
What I've done so far is as follows:
1) I copied the drivers that windows was using successfully from my
windows slice to my freebsd slice.
2) I made sure that the .inf file was ascii, after that I generated
bcmwl5_sys.ko with ndisgen.
3) I loaded the module generated, it loaded successfully.
At this point I expected to see a ndis0 device popup, however sadly this
wasn't the case.
Running after running pciconf -lv I think I've successfully identified
the miniPCI card as PCI:3:3:0 and the driver appears to see it, however
that's it.
Below is the snippit of my system log after attaching the driver. Below
that is the pciconf -lv output
pci0: driver added
pci1: driver added
pci2: driver added
pci3: driver added
found-> vendor=0x104c, dev=0x8038, revid=0x00
bus=3, slot=1, func=5
class=07-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0102, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=19
powerspec 2 supports D0 D1 D2 D3 current D0
pci3:1:5: reprobing on driver added
found-> vendor=0x14e4, dev=0x4318, revid=0x02
bus=3, slot=3, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=17
pci3:3:0: reprobing on driver added
pci0: driver added
pci1: driver added
pci2: driver added
pci3: driver added
found-> vendor=0x104c, dev=0x8038, revid=0x00
bus=3, slot=1, func=5
class=07-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0102, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=19
powerspec 2 supports D0 D1 D2 D3 current D0
pci3:1:5: reprobing on driver added
found-> vendor=0x14e4, dev=0x4318, revid=0x02
bus=3, slot=3, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=17
pci3:3:0: reprobing on driver added
Now the pciconf -lv output:
hostb0@pci0:0:0: class=0x060000 card=0x01821028 chip=0x25908086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82915PM/GM/GMS, 82910GML Host Bridge'
class = bridge
subclass = HOST-PCI
pcib1@pci0:1:0: class=0x060400 card=0x00000088 chip=0x25918086
rev=0x03 hdr=0x01
vendor = 'Intel Corporation'
device = '82915PM/GM PCI Express Graphics Port'
class = bridge
subclass = PCI-PCI
pcib2@pci0:28:0: class=0x060400 card=0x00000040 chip=0x26608086
rev=0x03 hdr=0x01
vendor = 'Intel Corporation'
device = '82801FB/FR/FW/FRW PCI Express Port 1'
class = bridge
subclass = PCI-PCI
uhci0@pci0:29:0: class=0x0c0300 card=0x01821028 chip=0x26588086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801FB/FR/FW/FRW USB UHCI Controller'
class = serial bus
subclass = USB
uhci1@pci0:29:1: class=0x0c0300 card=0x01821028 chip=0x26598086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801FB/FR/FW/FRW USB UHCI Controller'
class = serial bus
subclass = USB
uhci2@pci0:29:2: class=0x0c0300 card=0x01821028 chip=0x265a8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801FB/FR/FW/FRW USB UHCI Controller'
class = serial bus
subclass = USB
uhci3@pci0:29:3: class=0x0c0300 card=0x01821028 chip=0x265b8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801FB/FR/FW/FRW USB UHCI Controller'
class = serial bus
subclass = USB
ehci0@pci0:29:7: class=0x0c0320 card=0x01821028 chip=0x265c8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801FB/FR/FW/FRW USB 2.0 EHCI Controller'
class = serial bus
subclass = USB
pcib3@pci0:30:0: class=0x060401 card=0x00000050 chip=0x24488086
rev=0xd3 hdr=0x01
vendor = 'Intel Corporation'
device = '82801BAM/CAM/DBM (ICH2-M/3-M/4-M) Hub Interface to PCI
Bridge'
class = bridge
subclass = PCI-PCI
pcm0@pci0:30:2: class=0x040100 card=0x01821028 chip=0x266e8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801FB/FR/FW/FRW AC '97 Audio Controller'
class = multimedia
subclass = audio
isab0@pci0:31:0: class=0x060100 card=0x01821028 chip=0x26418086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801FBM ICH6M LPC Interface Bridge'
class = bridge
subclass = PCI-ISA
atapci0@pci0:31:2: class=0x010180 card=0x01821028 chip=0x26538086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801FBM ICH6M SATA Controller'
class = mass storage
subclass = ATA
drm0@pci1:0:0: class=0x030000 card=0x20061028 chip=0x54601002
rev=0x00 hdr=0x00
vendor = 'ATI Technologies Inc'
device = 'Mobility Radeon X300'
class = display
subclass = VGA
bge0@pci2:0:0: class=0x020000 card=0x01821028 chip=0x167714e4
rev=0x01 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'BCM5750A1 NetXtreme Gigabit Ethernet PCI Express'
class = network
subclass = ethernet
cbb0@pci3:1:0: class=0x060700 card=0x01821028 chip=0x8036104c
rev=0x00 hdr=0x02
vendor = 'Texas Instruments (TI)'
class = bridge
subclass = PCI-CardBus
none0@pci3:1:5: class=0x078000 card=0x01821028 chip=0x8038104c
rev=0x00 hdr=0x00
vendor = 'Texas Instruments (TI)'
device = '01821028 GemCore based SmartCard container'
class = simple comms
none1@pci3:3:0: class=0x028000 card=0x00051028 chip=0x431814e4
rev=0x02 hdr=0x00
vendor = 'Broadcom Corporation'
class = network
Any advice would is welcome. If I can get the wireless card working and
resolve an ACPI video issue I have, I will have just about everything
that I'm interested in, fully functional.
Thank you
-cf
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"