Re: Interrupt Storms on irq:11 with Tecra A4

On Tue, 2006-07-04 at 18:56 +0300, Yousef Raffah wrote:
> On Tue, 2006-07-04 at 16:27 +0300, Yousef Raffah wrote:
> > I just updated my BIOS yesterday in order to test if my laptop will
> > "ever" work with ACPI under FreeBSD.
> > 
> > The test resulted in having interrupt storm on irq:11 whenever acpi is
> > enabled during the boot process. I have tried to disable apic from my
> > kernel but that didn't help, same results.
> > I know interrupt storms can be "ok" to ignore but I guess that is not an
> > option in my case as it is disabling my hard drive!
> > 
> > Googling for interrupt storm gave me results of people having the same
> > problem but I still can't find how to overcome this. Not sure if I can
> > get a dmesg output with the interrupt storm, any ideas?
> > 
Sorry for bothering everyone on the list with my problem but I really
need to get over this interrupt storm thing. Can someone at least tell
me what am I supposed to do (without flaming please :) ) in order to
overcome this?

> I just thought these information might be very helpful:
> 
> vmstat -i
> interrupt                          total       rate
> irq0: clk                          85625        984
> irq1: atkbd0                         244          2
> irq3: sio1                             1          0
> irq4: sio0                             1          0
> irq7: ppc0                             2          0
> irq8: rtc                          10960        125
> irq11: cbb0 myk0+*                   237          2
> irq14: ata0                         2373         27
> irq15: ata1                          127          1
> Total                              99570       1144
> 
> 
> Here is my pciconf -lv:
> 
> hostb0@pci0:0:0:        class=0x060000 card=0xff101179 chip=0x25908086
> rev=0x03 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82915PM/GM/GMS, 82910GML Host Bridge'
>     class    = bridge
>     subclass = HOST-PCI
> pcib1@pci0:1:0: class=0x060400 card=0x00000088 chip=0x25918086 rev=0x03
> hdr=0x01
>     vendor   = 'Intel Corporation'
>     device   = '82915PM/GM PCI Express Graphics Port'
>     class    = bridge
>     subclass = PCI-PCI
> pcib2@pci0:28:0:        class=0x060400 card=0x00000040 chip=0x26608086
> rev=0x04 hdr=0x01
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW PCI Express Port 1'
>     class    = bridge
>     subclass = PCI-PCI
> pcib3@pci0:28:1:        class=0x060400 card=0x00000040 chip=0x26628086
> rev=0x04 hdr=0x01
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW PCI Express Port 2'
>     class    = bridge
>     subclass = PCI-PCI
> uhci0@pci0:29:0:        class=0x0c0300 card=0xff101179 chip=0x26588086
> rev=0x04 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW USB UHCI Controller'
>     class    = serial bus
>     subclass = USB
> uhci1@pci0:29:1:        class=0x0c0300 card=0xff101179 chip=0x26598086
> rev=0x04 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW USB UHCI Controller'
>     class    = serial bus
>     subclass = USB
> uhci2@pci0:29:2:        class=0x0c0300 card=0xff101179 chip=0x265a8086
> rev=0x04 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW USB UHCI Controller'
>     class    = serial bus
>     subclass = USB
> uhci3@pci0:29:3:        class=0x0c0300 card=0xff101179 chip=0x265b8086
> rev=0x04 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW USB UHCI Controller'
>     class    = serial bus
>     subclass = USB
> ehci0@pci0:29:7:        class=0x0c0320 card=0xff101179 chip=0x265c8086
> rev=0x04 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW USB 2.0 EHCI Controller'
>     class    = serial bus
>     subclass = USB
> pcib4@pci0:30:0:        class=0x060401 card=0x00000050 chip=0x24488086
> rev=0xd4 hdr=0x01
>     vendor   = 'Intel Corporation'
>     device   = '82801BAM/CAM/DBM (ICH2-M/3-M/4-M) Hub Interface to PCI
> Bridge'
>     class    = bridge
>     subclass = PCI-PCI
> pcm0@pci0:30:2: class=0x040100 card=0xff101179 chip=0x266e8086 rev=0x04
> hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW AC '97 Audio Controller'
>     class    = multimedia
>     subclass = audio
> none0@pci0:30:3:        class=0x070300 card=0x00011179 chip=0x266d8086
> rev=0x04 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FB/FR/FW/FRW AC '97 Modem Controller'
>     class    = simple comms
>     subclass = generic modem
> isab0@pci0:31:0:        class=0x060100 card=0xff101179 chip=0x26418086
> rev=0x04 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FBM ICH6M LPC Interface Bridge'
>     class    = bridge
>     subclass = PCI-IS
> atapci0@pci0:31:2:      class=0x010180 card=0xff101179 chip=0x26538086
> rev=0x04 hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = '82801FBM ICH6M SATA Controller'
>     class    = mass storage
>     subclass = ATA
> none1@pci1:0:0: class=0x030000 card=0xff101179 chip=0x54601002 rev=0x00
> hdr=0x00
>     vendor   = 'ATI Technologies Inc'
>     device   = 'Mobility Radeon X300'
>     class    = display
>     subclass = VGA
> myk0@pci2:0:0:  class=0x020000 card=0xff101179 chip=0x436211ab rev=0x15
> hdr=0x00
>     vendor   = 'Marvell Semiconductor (Was: Galileo Technology Ltd)'
>     device   = '88E8053 Yukon PCI-E Gigabit Ethernet Controller
> (copper)'
>     class    = network
>     subclass = ethernet
> iwi0@pci6:4:0:  class=0x028000 card=0x27418086 chip=0x42208086 rev=0x05
> hdr=0x00
>     vendor   = 'Intel Corporation'
>     device   = 'PRO/Wireless 2200BG Network Connection'
>     class    = network
> cbb0@pci6:6:0:  class=0x060700 card=0xff101179 chip=0x8031104c rev=0x00
> hdr=0x02
>     vendor   = 'Texas Instruments (TI)'
>     class    = bridge
>     subclass = PCI-CardBus
> fwohci0@pci6:6:2:       class=0x0c0010 card=0xff101179 chip=0x8032104c
> rev=0x00 hdr=0x00
>     vendor   = 'Texas Instruments (TI)'
>     class    = serial bus
>     subclass = FireWire
> none2@pci6:6:3: class=0x018000 card=0xff101179 chip=0x8033104c rev=0x00
> hdr=0x00
>     vendor   = 'Texas Instruments (TI)'
>     device   = 'PCIxx21 Integrated FlashMedia Controller'
>     class    = mass storage
> none3@pci6:6:4: class=0x080500 card=0xff101179 chip=0x8034104c rev=0x00
> hdr=0x00
>     vendor   = 'Texas Instruments (TI)'
>     class    = base peripheral
> 
> 
> And here is my dmesg (without acpi)
> 
> 
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights
> reserved.
> FreeBSD 6.1-RELEASE-p1 #3: Mon Jul  3 17:23:38 AST 2006
>     root@redevil:/usr/obj/usr/src/sys/LAPTOP
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Pentium(R) M processor 1.86GHz (1862.01-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x6d8  Stepping = 8
> 
> Features=0xafe9f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,F
> XSR,SSE,SSE2,SS,TM,PBE>
>   Features2=0x180<EST,TM2>
> real memory  = 536735744 (511 MB)
> avail memory = 515883008 (491 MB)
> kbd1 at kbdmux0
> cpu0 on motherboard
> pcib0: <Host to PCI bridge> pcibus 0 on motherboard
> pir0: <PCI Interrupt Routing Table: 12 Entries> on motherboard
> pci0: <PCI bus> on pcib0
> pcib1: <PCIBIOS PCI-PCI bridge> irq 11 at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> pci1: <display, VGA> at device 0.0 (no driver attached)
> pcib2: <PCIBIOS PCI-PCI bridge> irq 10 at device 28.0 on pci0
> pci2: <PCI bus> on pcib2
> myk0: <Marvell 88E8053 Gigabit Ethernet Controller, Ver. 8.12.2.3> port
> 0xa000-0xa0ff mem 0xbc000000-0xbc
> 003fff irq 11 at device 0.0 on pci2
> myk0: Ethernet address: 00:a0:d1:bf:aa:e1
> pcib3: <PCIBIOS PCI-PCI bridge> irq 11 at device 28.1 on pci0
> pci3: <PCI bus> on pcib3
> uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port
> 0x1200-0x121f irq 11 at device 29.0 on 
> pci0
> uhci0: [GIANT-LOCKED]
> usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port
> 0x1220-0x123f irq 11 at device 29.1 on 
> pci0
> uhci1: [GIANT-LOCKED]
> usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
> usb1: USB revision 1.0
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port
> 0x1240-0x125f irq 11 at device 29.2 on 
> pci0
> uhci2: [GIANT-LOCKED]
> usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
> usb2: USB revision 1.0
> uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port
> 0x1260-0x127f irq 11 at device 29.3 on 
> pci0
> uhci3: [GIANT-LOCKED]
> usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
> usb3: USB revision 1.0
> uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub3: 2 ports with 2 removable, self powered
> ehci0: <Intel 82801FB (ICH6) USB 2.0 controller> mem
> 0xf4000000-0xf40003ff irq 11 at device 29.7 on pci0
> ehci0: [GIANT-LOCKED]
> usb4: EHCI version 1.0
> usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
> usb4: <Intel 82801FB (ICH6) USB 2.0 controller> on ehci0
> usb4: USB revision 2.0
> uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub4: 8 ports with 8 removable, self powered
> pcib4: <PCIBIOS PCI-PCI bridge> at device 30.0 on pci0
> pci6: <PCI bus> on pcib4
> iwi0: <Intel(R) PRO/Wireless 2200BG> mem 0xb000b000-0xb000bfff irq 11 at
> device 4.0 on pci6
> iwi0: Ethernet address: 00:12:f0:63:ae:ca
> cbb0: <PCI-CardBus Bridge> mem 0x13000000-0x13000fff at device 6.0 on
> pci6
> cardbus0: <CardBus bus> on cbb0
> pccard0: <16-bit PCCard bus> on cbb0
> fwohci0: <1394 Open Host Controller Interface> mem
> 0xb0000000-0xb00007ff,0xb0004000-0xb0007fff irq 11 at 
> device 6.2 on pci6
> fwohci0: OHCI version 1.10 (ROM=0)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 00:08:0d:a0:d1:bf:aa:e1
> fwohci0: Phy 1394a available S400, 2 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> firewire0: <IEEE1394(FireWire) bus> on fwohci0
> sbp0: <SBP-2/SCSI over FireWire> on firewire0
> fwohci0: Initiate bus reset
> fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
> firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> firewire0: bus manager 0 (me)
> pci6: <mass storage> at device 6.3 (no driver attached)
> pci6: <base peripheral> at device 6.4 (no driver attached)
> pcm0: <Intel ICH6 (82801FB)> port 0xe000-0xe0ff,0xe100-0xe13f mem
> 0xd0000000-0xd00001ff,0xd0000200-0xd000
> 02ff irq 10 at device 30.2 on pci0
> pcm0: <Analog Devices AD1981B AC97 Codec>
> pci0: <simple comms, generic modem> at device 30.3 (no driver attached)
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH6 SATA150 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1100-0x110f at device
>  31.2 on pci0
> atapci0: failed to enable memory mapping!
> ata0: <ATA channel 0> on atapci0
> ata1: <ATA channel 1> on atapci0
> pmtimer0 on isa0
> orm0: <ISA Option ROMs> at iomem
> 0xc0000-0xcffff,0xe0000-0xe1fff,0xe5000-0xe5fff,0xeb000-0xeffff on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/8 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> isa0
> unknown: <PNP0c01> can't assign resources (memory)
> unknown: <PNP0303> can't assign resources (port)
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: [GIANT-LOCKED]
> psm0: model Generic PS/2 mouse, device ID 0
> unknown: <PNP0501> can't assign resources (port)
> unknown: <SMCf010> can't assign resources (port)
> unknown: <PNP0401> can't assign resources (port)
> ums0: Mitsumi Electric Apple Optical USB Mouse, rev 1.10/1.08, addr 2,
> iclass 3/1
> ums0: 4 buttons and Z dir.
> Timecounter "TSC" frequency 1862008934 Hz quality 800
> Timecounters tick every 1.000 msec
> ad0: 76319MB <FUJITSU MHT2080AT 0022> at ata0-master UDMA100
> acd0: DVDR <MATSHITADVD-RAM UJ-831S/1.40> at ata1-master UDMA33
> cd0 at ata1 bus 0 target 0 lun 0
> cd0: <MATSHITA DVD-RAM UJ-831S 1.40> Removable CD-ROM SCSI-0 device 
> cd0: 33.000MB/s transfers
> cd0: cd present [1790992 x 2048 byte records]
> Trying to mount root from ufs:/dev/ad0s2a
> 
> 
> --
> Sincerely,
> Yousef Raffah
> Senior Systems Administrator
> --
> 
> Aren't you using Firefox? Get it at http://www.getfirefox.com
> 
> 

--
Sincerely,
Yousef Raffah
Senior Systems Administrator
--

Aren't you using Firefox? Get it at http://www.getfirefox.com

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (FreeBSD)

iD8DBQBEq9EWH9IXMb4e6CMRAq0CAJ9dDA7DT0t1TJ+sTNrDzi7UTen8yACgkWhJ
+5A2+Ylh02amI+vnnGh+PIY=
=zYI9
-----END PGP SIGNATURE-----