dialup question

Emanuel Haupt <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile
Message-ID <[email protected]> 
i am using the following network/modem (all in 1) card on my dell 
latitude cpx laptop (running fbsd 5.0-DP1 newcard kernel):

3com 3c3fem656 c

the xl0 network interface works without any problems. but now i want to 
use the included modem.

i have absolutely no clue which device that would be. attached is the 
complete dmesg output.

does anyone know which device i have to configure in my ppp.conf?

thanks in advance
emanuel
dmesg.txt (text/plain, 4.9 KB) 
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.0-DP1 #0: Sun Jul 21 17:43:29 CEST 2002
    [email protected]:/usr/src/sys/i386/compile/SNOOD2
Preloaded elf kernel "/boot/kernel/kernel" at 0xc063b000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc063b0a8.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 498470166 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (498.47-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x686  Stepping = 6
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 134066176 (130924K bytes)
avail memory = 123580416 (120684K bytes)
Pentium Pro MTRR support enabled
Using $PIR table, 6 entries at 0xc00fbd20
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL   CPi R  > on motherboard
Timecounter "ACPI-safe"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_pcib0: <Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <PCI bus> on acpi_pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pccbb0: <TI1225 PCI-CardBus Bridge> at device 3.0 on pci0
cardbus0: <CardBus bus> on pccbb0
pccard0: <16-bit PCCard bus> on pccbb0
acpi_pcib0: device is routed to IRQ 11
pccbb1: <TI1225 PCI-CardBus Bridge> at device 3.1 on pci0
cardbus1: <CardBus bus> on pccbb1
pccard1: <16-bit PCCard bus> on pccbb1
acpi_pcib0: device is routed to IRQ 11
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x860-0x86f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xdce0-0xdcff irq 11 at device 7.2 on pci0
usb0: cannot stop
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pci0: <multimedia, audio> at device 8.0 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x280-0x287,0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.20 initialized.  Default = pass all, Logging = enabled
system power profile changed to 'economy'
Product version: 5.0
Product name: 3Com Corporation | 3CXFEM656C-LAN | LAN | 1 | 
Manufacturer ID: 02016465
Functions: Network Adaptor, Multi-Functioned
CIS reading done
cardbus0: Resource not specified in CIS: id=18, size=80
xl0: <3Com 3c656C Fast Etherlink XL> port 0x1000-0x107f mem 0x84002100-0x8400217f,0x84002000-0x840020ff irq 11 at device 0.0 on cardbus0
xl0: Ethernet address: 00:01:03:9a:dd:84
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Product version: 5.0
Product name: 3Com Corporation | 3CXFEM656C-MDM | MDM | 1 | 
Manufacturer ID: 02016565
Functions: Serial Port, Multi-Functioned
Function Extension: 011f3f000400000400
Function Extension: 0206003f1c03030f060000ff
Function Extension: 1306000f006a00ff
Function Extension: 2306000f000200ff
CIS reading done
cardbus0: Resource not specified in CIS: id=10, size=100
cardbus0: Resource not specified in CIS: id=14, size=100
cardbus0: <unknown card> (vendor=0x10b7, dev=0x6565) at 0.1 irq 11
ad0: 19077MB <IBM-DJSA-220> [38760/16/63] at ata0-master UDMA33
acd0: CDROM <SAMSUNG CD-ROM SN-124> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.