Linksys WPC54G V3 problem
"Ben K." <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
I have searched through the mobile list and followed all advice I
could find to no avail. I am able to get FreeBSD 6.1-Release to
recognize and load my Linksys WPC54G V3 using ndsigen. The interface
ndis0 comes up and if I issue a 'ifconfig ndis0 scan' it will see my
Linksys router however It doesn't associate to it.
I can set the IP and the netmask but it will not set the ssid or
channel properly, which I believe is at the root of my problem.
I enabled several debuging options in /boot/loader.conf and then
rebooted using verbose logging.
Here is my dmesg output:
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE-p10 #1: Fri Oct 13 21:45:22 MST 2006
root@dev-laptop:/usr/obj/usr/src/sys/DEV-LAPTOP
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0b7e000.
Preloaded elf module "/boot/kernel/if_ndis.ko" at 0xc0b7e14c.
Preloaded elf module "/boot/kernel/ndis.ko" at 0xc0b7e1f8.
Preloaded elf module "/boot/kernel/bcmwl5_sys.ko" at 0xc0b7e2a4.
Preloaded elf module "/boot/kernel/wlan_wep.ko" at 0xc0b7e354.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0b7e404.
Calibrating clock(s) ... i8254 clock: 1097801 Hz
1097801 Hz differs from default of 1193182 Hz by more than 1%
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 647189055 Hz
CPU: Intel Pentium III (647.19-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 268283904 (255 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c25000 - 0x000000000fb22fff, 250601472 bytes (61182 pages)
avail memory = 253038592 (241 MB)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xc0ae
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4 Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
rr232x: RocketRAID 232x controller driver v1.02 (Oct 13 2006 21:44:36)
npx0: INT 16 interface
acpi0: <DELL CPi R > on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000060
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcibios: BIOS version 2.10
Found $PIR table, 6 entries at 0xc00fbd20
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 7 D 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 1 0 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 1 0 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 3 A 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 3 B 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 8 A 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 8 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 13 A 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 17 A 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 17 B 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 17 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 17 D 0x62 3 4 5 6 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
atpic: Programming IRQ9 as level/low
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 5 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
ACPI timer: 0/4 0/4 0/4 0/4 0/4 0/4 0/4 0/4 0/4 0/4 -> 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.7.INTD at func 2: 11
ACPI: Found matching pin for 0.3.INTA at func 0: 255
ACPI: Found matching pin for 0.3.INTA at func 1: 255
ACPI: Found matching pin for 0.13.INTA at func 0: 10
ACPI: Found matching pin for 0.8.INTA at func 0: 5
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x7190, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base f4000000, size 26, enabled
found-> vendor=0x8086, dev=0x7191, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x011f, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x8c (35000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x104c, dev=0xac1c, revid=0x01
bus=0, slot=3, func=0
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
intpin=a, irq=255
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 00000000, size 12, memory disabled
found-> vendor=0x104c, dev=0xac1c, revid=0x01
bus=0, slot=3, func=1
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
intpin=a, irq=255
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 00000000, size 12, memory disabled
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=7, func=0
class=06-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00000860, size 4, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
map[20]: type 4, range 32, base 0000dce0, size 5, enabled
pcib0: matched entry for 0.7.INTD (src \\_SB_.PCI0.LNKD:0)
pcib0: slot 7 INTD routed to irq 11 via \\_SB_.PCI0.LNKD
found-> vendor=0x8086, dev=0x7113, revid=0x03
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[90]: type 4, range 32, base 00000840, size 4, enabled
found-> vendor=0x125d, dev=0x1998, revid=0x10
bus=0, slot=8, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000d800, size 8, enabled
map[14]: type 1, range 32, base faffe000, size 13, enabled
pcib0: matched entry for 0.8.INTA (src \\_SB_.PCI0.LNKB:0)
pcib0: slot 8 INTA routed to irq 5 via \\_SB_.PCI0.LNKB
found-> vendor=0x10b7, dev=0x9200, revid=0x6c
bus=0, slot=13, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000dc00, size 7, enabled
map[14]: type 1, range 32, base faffdc00, size 7, enabled
pcib0: matched entry for 0.13.INTA (src \\_SB_.PCI0.LNKC:0)
pcib0: slot 13 INTA routed to irq 10 via \\_SB_.PCI0.LNKC
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem
0xf4000000-0xf7ffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xf4000000
agp0: allocating GATT for aperture of size 64M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xe000-0xefff
pcib1: memory decode 0xfc000000-0xfeffffff
pcib1: prefetched decode 0xfff00000-0xfffff
ACPI: Found matching pin for 1.0.INTA at func 0: 11
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x4c4d, revid=0x64
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fd000000, size 24, enabled
pcib1: (null) requested memory range 0xfd000000-0xfdffffff: good
map[14]: type 4, range 32, base 0000ec00, size 8, enabled
pcib1: (null) requested I/O range 0xec00-0xecff: in range
map[18]: type 1, range 32, base fcfff000, size 12, enabled
pcib1: (null) requested memory range 0xfcfff000-0xfcffffff: good
pcib1: matched entry for 1.0.INTA (src \\_SB_.PCI0.LNKA:0)
pcib1: slot 0 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1225 PCI-CardBus Bridge> at device 3.0 on pci0
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80000000
cbb0: Found memory at 80000000
cbb0: Secondary bus is 4
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: matched entry for 0.3.INTA (src \\_SB_.PCI0.LNKD:0)
pcib0: slot 3 INTA routed to irq 11 via \\_SB_.PCI0.LNKD
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0xac1c104c 0x02100007 0x06070001 0x00822008
0x10: 0x80000000 0x020000a0 0x20040400 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b
0x40: 0x00bb1028 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x2024d021 0x00000000 0x00000000 0x01261222
0x90: 0x6066a6c0 0x00000000 0x00000000 0x00000000
0xa0: 0x7e210001 0x00800000 0x0000081b 0x00000007
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
cbb1: <TI1225 PCI-CardBus Bridge> at device 3.1 on pci0
cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80001000
cbb1: Found memory at 80001000
cbb1: Secondary bus is 5
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib0: matched entry for 0.3.INTA (src \\_SB_.PCI0.LNKD:0)
pcib0: slot 3 INTA routed to irq 11 via \\_SB_.PCI0.LNKD
cbb1: [MPSAFE]
cbb1: PCI Configuration space:
0x00: 0xac1c104c 0x02100007 0x06070001 0x00822008
0x10: 0x80001000 0x220000a0 0x20050500 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b
0x40: 0x00bb1028 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x2024d021 0x00000000 0x00000000 0x01261222
0x90: 0x6066a6c0 0x00000000 0x00000000 0x00000000
0xa0: 0x7e210001 0x00808000 0x0000081b 0x00000007
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
PCI-ISA bridge with incorrect subclass 0x80
PCI-ISA bridge with incorrect subclass 0x80
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x860-0x86f at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x860
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=01
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x01 err=0x04 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=01 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xdce0-0xdcff
irq 11 at device 7.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xdce0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
pci0: <multimedia, audio> at device 8.0 (no driver attached)
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xdc00-0xdc7f mem
0xfaffdc00-0xfaffdc7f irq 10 at device 13.0 on pci0
xl0: Reserved 0x80 bytes for rid 0x14 type 3 at 0xfaffdc00
xl0: using memory mapped I/O
xl0: media options word: a
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:c0:4f:3b:a5:6f
xl0: [MPSAFE]
acpi_tz0: <Thermal Zone> on acpi0
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5,0x3f7 irq 6 drq
2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
sio0: irq maps: 0x301 0x311 0x301 0x301
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7
drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ex_isa_identify()
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 13: ioport 0xdc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x301 0x301 0x301 0x301
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 647189055 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
rr232x: no controller detected.
acpi_acad0: acline initialization start
battery0: battery initialization start
Status is 0x30000106
Status is 0x30000920
cbb1: card inserted: event=0x00000000, state=30000920
cbb1: cbb_power: 3V
cardbus1: CIS pointer is 0!
cardbus1: Resource not specified in CIS: id=10, size=2000
cardbus1: Non-prefetchable memory at 88000000-88001fff
found-> vendor=0x14e4, dev=0x4318, revid=0x02
bus=5, slot=0, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
ndis0: <Wireless-G Notebook Adapter WPC54G V3> mem
0x88000000-0x88001fff irq 11 at device 0.0 on cardbus1
ndis0: Reserved 0x2000 bytes for rid 0x10 type 3 at 0x88000000
ndis0: Reserved 0x1 bytes for rid 0 type 1 at 0xb
ndis0: [MPSAFE]
ndis0: NDIS API version: 5.1
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
battery1: battery initialization start
battery0: battery initialization done, tried 1 times
ndis0: bpf attached
ndis0: Ethernet address: 00:13:10:e5:46:e3
ndis0: bpf attached
ad0: setting PIO4 on PIIX4 chip
ad0: setting UDMA33 on PIIX4 chip
ad0: 38154MB <FUJITSU MHT2040AH 006C> at ata0-master UDMA33
ad0: 78140160 sectors [77520C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ad0: Intel check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on PIIX4 chip
acd0: setting UDMA33 on PIIX4 chip
acd0: <TEAC CD-ROM CD-224E/3.7C> CDROM drive at ata1 as master
acd0: read 4134KB/s (4134KB/s), 128KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ATA PseudoRAID loaded
Trying to mount root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
Here is what I type to try and set the interface settings:
ifconfig ndis0 inet 192.168.x.x netmask 255.255.255.0 ssid MYSSID channel 09 w
epmode on wepkey 0xMy_26_Char_Key deftkey 1
Here is the ifconfig output for that int:
ndis0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 192.168.x.x netmask 0xffffff00 broadcast 0.0.0.1
inet6 fe80::213:10ff:fee5:46e3%ndis0 prefixlen 64 scopeid 0x4
ether 00:13:10:e5:46:e3
media: IEEE 802.11 Wireless Ethernet autoselect
status: no carrier
ssid "" channel 1
authmode OPEN privacy ON deftxkey UNDEF wepkey 1:104-bit txpowmax 100
protmode CTS
Any help on this is appreciated.
-Ben.
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"