Re: Too hot temperature of disk - HP Compaq nc6220
Zoran Kolic <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
> debug.acpi.do_powerstate: 1
> hw.acpi.supported_sleep_state: S3 S4 S5
> hw.acpi.power_button_state: S5
> hw.acpi.sleep_button_state: S3
> hw.acpi.lid_switch_state: NONE
> hw.acpi.standby_state: S1
> hw.acpi.suspend_state: S3
> hw.acpi.sleep_delay: 1
> hw.acpi.s4bios: 1
> hw.acpi.verbose: 0
> hw.acpi.reset_video: 1
> hw.acpi.cpu.cx_supported: C1/1 C2/2 C3/38
I have set in rc.conf:
performance_cx_lowest="LOW"
economy_cx_lowest="LOW"
> hw.acpi.cpu.cx_lowest: C1
> hw.acpi.cpu.cx_usage: 100.00% 0.00% 0.00%
Above options wuold change this.
> hw.acpi.thermal.tz0.temperature: 59.0C
A little bit high.
> hw.acpi.thermal.tz0.active: 2
> hw.acpi.thermal.tz0.passive_cooling: 1
> hw.acpi.thermal.tz0.thermal_flags: 0
> hw.acpi.thermal.tz0._PSV: 100.0C
> hw.acpi.thermal.tz0._HOT: -1
> hw.acpi.thermal.tz0._CRT: 105.0C
> hw.acpi.thermal.tz0._ACx: 80.0C 70.0C 55.0C 35.0C -1 -1 -1 -1 -1 -1
> hw.acpi.thermal.tz1.temperature: 45.0C
> hw.acpi.thermal.tz1.active: -1
> hw.acpi.thermal.tz1.passive_cooling: 0
> hw.acpi.thermal.tz1.thermal_flags: 0
> hw.acpi.thermal.tz1._PSV: -1
> hw.acpi.thermal.tz1._HOT: -1
> hw.acpi.thermal.tz1._CRT: 103.0C
> hw.acpi.thermal.tz1._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
> hw.acpi.thermal.tz2.temperature: 16.0C
> hw.acpi.thermal.tz2.active: -1
> hw.acpi.thermal.tz2.passive_cooling: 0
> hw.acpi.thermal.tz2.thermal_flags: 0
> hw.acpi.thermal.tz2._PSV: 60.0C
> hw.acpi.thermal.tz2._HOT: -1
> hw.acpi.thermal.tz2._CRT: 105.0C
> hw.acpi.thermal.tz2._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
>
> I loaded cpufreq.ko (default, without any compilation), effect:
> ola# kldload cpufreq
I have it in kernel.
And in rc.conf:
powerd_enable="YES"
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: Please update driver or contact the maintainer.
> est: cpu_vendor GenuineIntel, msr 6120e2906000e29, bus_clk, 64
> device_attach: est0 attach returned 6
I've put in /boot/loader.conf:
hint.ichss.0.disabled="1"
Best regards
Zoran
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"