Testing boot and hardware, FreeBSD6.2 on laptop Samsung NP-Q45(A002)

Only for info.

in kernconf delete only ipv6
in loader.conf snd_driver_load="YES"

FreeBSD  6.2-STABLE FreeBSD 6.2-STABLE #0: Wed May 30 18:36:03 MSD 
2007     [email protected]:/usr/obj/usr/src/sys/C01  i386
==== start dmesg  ==========
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE #0: Wed May 30 18:36:03 MSD 2007
    [email protected]:/usr/obj/usr/src/sys/C01
ACPI APIC Table: <INTEL  CRESTLNE>
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Duo CPU     T7300  @ 2.00GHz (1995.02-MHz 
686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6fa  Stepping = 10
  
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,<b14>,<b15>>
  AMD Features=0x20000000<LM>
  AMD Features2=0x1<LAHF>
  Cores per package: 2
real memory  = 1064108032 (1014 MB)
avail memory = 1031852032 (984 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Changing APIC ID to 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <SECCSD LH43STAR> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
Timecounter "HPET" frequency 14318180 Hz quality 2000
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x17> port 0x62,0x66 on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 2.0 (no driver attached)
pci0: <display> at device 2.1 (no driver attached)
uhci0: <UHCI (generic) USB controller> port 0x1820-0x183f irq 16 at 
device 26.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x1840-0x185f irq 21 at 
device 26.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf0704000-0xf07043ff irq 
18 at device 26.7 on pci0
ehci0: [GIANT-LOCKED]
usb2: EHCI version 1.0
usb2: companion controllers, 2 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
ugen0: Vimicro Corp. Vega USB 2.0 Camera., rev 2.00/1.00, addr 2
pcm0: <Intel 82801H High Definition Audio Controller> mem 
0xf0500000-0xf0503fff irq 22 at device 27.0 on pci0
pcib1: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib1
pci2: <network> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci3: <ACPI PCI bus> on pcib2
pci3: <network, ethernet> at device 0.0 (no driver attached)
uhci2: <UHCI (generic) USB controller> port 0x1860-0x187f irq 23 at 
device 29.0 on pci0
uhci2: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci2
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0x1880-0x189f irq 19 at 
device 29.1 on pci0
uhci3: [GIANT-LOCKED]
usb4: <UHCI (generic) USB controller> on uhci3
usb4: USB revision 1.0
uhub4: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhci4: <UHCI (generic) USB controller> port 0x18a0-0x18bf irq 18 at 
device 29.2 on pci0
uhci4: [GIANT-LOCKED]
usb5: <UHCI (generic) USB controller> on uhci4
usb5: USB revision 1.0
uhub5: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf0704400-0xf07047ff irq 
23 at device 29.7 on pci0
ehci1: [GIANT-LOCKED]
usb6: EHCI version 1.0
usb6: companion controllers, 2 ports each: usb3 usb4 usb5
usb6: <EHCI (generic) USB 2.0 controller> on ehci1
usb6: USB revision 2.0
uhub6: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
umass0: USBest Technology USB Mass Storage Device, rev 2.00/1.00, addr 2
pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci4: <ACPI PCI bus> on pcib3
pci4: <bridge, PCI-CardBus> at device 9.0 (no driver attached)
pci4: <serial bus, FireWire> at device 9.1 (no driver attached)
pci4: <base peripheral> at device 9.2 (no driver attached)
pci4: <base peripheral> at device 9.3 (no driver attached)
pci4: <base peripheral> at device 9.4 (no driver attached)
pci4: <base peripheral> at device 9.5 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <GENERIC ATA controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x18e0-0x18ef,0x18d0-0x18df at 
device 31.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xdc000-0xdffff,0xe0000-0xe17ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: parallel port not found.
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ugen1: Broadcom Corp BCM92045NMD, rev 2.00/3.54, addr 2
Timecounters tick every 1.000 msec
ipfw2 initialized, divert enabled, rule-based forwarding disabled, 
default to accept, logging limited to 10 packets/entry by default
ad0: 114473MB <Hitachi HTS541612J9SA00 SBDOC70P> at ata0-master UDMA33
acd0: DVDR <TSSTcorpCD/DVDW TS-L632D/SC03> at ata1-master UDMA33
pcm0: <HDA Codec: Realtek ALC262>
pcm0: <HDA Driver Revision: 20070505_0044>
SMP: AP CPU #1 Launched!
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <JetFlash TS2GJF160 0.00> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1999MB (4095999 512 byte sectors: 255H 63S/T 254C)
Trying to mount root from ufs:/dev/ad0s1a
=========== end dmesg =============

=========== start pciconf -lv ==========
hostb0@pci0:0:0:        class=0x060000 card=0xc510144d chip=0x2a008086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = bridge
    subclass = HOST-PCI
none0@pci0:2:0: class=0x030000 card=0xc510144d chip=0x2a028086 rev=0x03 
hdr=0x00
    vendor   = 'Intel Corporation'
    class    = display
    subclass = VGA
none1@pci0:2:1: class=0x038000 card=0xc510144d chip=0x2a038086 rev=0x03 
hdr=0x00
    vendor   = 'Intel Corporation'
    class    = display
uhci0@pci0:26:0:        class=0x0c0300 card=0xc510144d chip=0x28348086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = serial bus
    subclass = USB
uhci1@pci0:26:1:        class=0x0c0300 card=0xc510144d chip=0x28358086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = serial bus
    subclass = USB
ehci0@pci0:26:7:        class=0x0c0320 card=0xc510144d chip=0x283a8086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = serial bus
    subclass = USB
pcm0@pci0:27:0: class=0x040300 card=0xc510144d chip=0x284b8086 rev=0x03 
hdr=0x00
    vendor   = 'Intel Corporation'
    class    = multimedia
pcib1@pci0:28:0:        class=0x060400 card=0xc510144d chip=0x283f8086 
rev=0x03 hdr=0x01
    vendor   = 'Intel Corporation'
    class    = bridge
    subclass = PCI-PCI
pcib2@pci0:28:1:        class=0x060400 card=0xc510144d chip=0x28418086 
rev=0x03 hdr=0x01
    vendor   = 'Intel Corporation'
    class    = bridge
    subclass = PCI-PCI
uhci2@pci0:29:0:        class=0x0c0300 card=0xc510144d chip=0x28308086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = serial bus
    subclass = USB
uhci3@pci0:29:1:        class=0x0c0300 card=0xc510144d chip=0x28318086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = serial bus
    subclass = USB
uhci4@pci0:29:2:        class=0x0c0300 card=0xc510144d chip=0x28328086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = serial bus
    subclass = USB
ehci1@pci0:29:7:        class=0x0c0320 card=0xc510144d chip=0x28368086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = serial bus
    subclass = USB
pcib3@pci0:30:0:        class=0x060401 card=0x00000000 chip=0x24488086 
rev=0xf3 hdr=0x01
    vendor   = 'Intel Corporation'
    device   = '82801BAM/CAM/DBM (ICH2-M/3-M/4-M) Hub Interface to PCI 
Bridge'
    class    = bridge
    subclass = PCI-PCI
isab0@pci0:31:0:        class=0x060100 card=0xc510144d chip=0x28158086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = bridge
    subclass = PCI-ISA
atapci0@pci0:31:2:      class=0x010180 card=0xc510144d chip=0x28288086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = mass storage
    subclass = ATA
none2@pci0:31:3:        class=0x0c0500 card=0xc510144d chip=0x283e8086 
rev=0x03 hdr=0x00
    vendor   = 'Intel Corporation'
    class    = serial bus
    subclass = SMBus
none3@pci2:0:0: class=0x028000 card=0x10018086 chip=0x42228086 rev=0x02 
hdr=0x00
    vendor   = 'Intel Corporation'
    class    = network
none4@pci3:0:0: class=0x020000 card=0xc510144d chip=0x435311ab rev=0x15 
hdr=0x00
    vendor   = 'Marvell Semiconductor (Was: Galileo Technology Ltd)'
    class    = network
    subclass = ethernet
none5@pci4:9:0: class=0x060700 card=0xc510144d chip=0x04761180 rev=0xb4 
hdr=0x02
    vendor   = 'Ricoh Co Ltd'
    device   = 'RL5c476 CardBus Controller'
    class    = bridge
    subclass = PCI-CardBus
none6@pci4:9:1: class=0x0c0010 card=0xc510144d chip=0x05521180 rev=0x09 
hdr=0x00
    vendor   = 'Ricoh Co Ltd'
    device   = 'RL5c552 IEEE-1394 Controller'
    class    = serial bus
    subclass = FireWire
none7@pci4:9:2: class=0x080500 card=0xc510144d chip=0x08221180 rev=0x18 
hdr=0x00
    vendor   = 'Ricoh Co Ltd'
    device   = 'SD Bus Host Adapter'
    class    = base peripheral
none8@pci4:9:3: class=0x088000 card=0xc510144d chip=0x08431180 rev=0x00 
hdr=0x00
    vendor   = 'Ricoh Co Ltd'
    class    = base peripheral
none9@pci4:9:4: class=0x088000 card=0xc510144d chip=0x05921180 rev=0x09 
hdr=0x00
    vendor   = 'Ricoh Co Ltd'
    device   = 'Memory Stick Bus Host Adapter'
    class    = base peripheral
none10@pci4:9:5:        class=0x088000 card=0xc510144d chip=0x08521180 
rev=0x04 hdr=0x00
    vendor   = 'Ricoh Co Ltd'
    class    = base peripheral
============== end pciconf -lv ========================

============== start usbdevs ===========================
addr 1: UHCI root hub, Intel
addr 1: UHCI root hub, Intel
addr 1: EHCI root hub, Intel
 addr 2: Vega USB 2.0 Camera., Vimicro Corp.
addr 1: UHCI root hub, Intel
addr 1: UHCI root hub, Intel
addr 1: UHCI root hub, Intel
 addr 2: BCM92045NMD, Broadcom Corp
addr 1: EHCI root hub, Intel
 addr 2: USB Mass Storage Device, USBest Technology
================ end usbdevs =======================


_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"