TP-WN610G doesn't work on HP laptop.

Hello, I have some problem on my laptop.--some problem of wireless.


By that information follow, we could know that the cardbus is found.It is on
cbb0.
But when I use TP-Link WN610G (also is TL-WN610G) to connect the wireless
network.The card doesn't work. The lights of the card don't flash or light.

I load the module named "if_ath.ko" (because the card use Atheros's clip).

My laptop is HP Pavilion ze2205au.


Wait for your help.

Wayne

P.S.
I could use the wireless card on Ubuntu.And there are some problem on my
ACPI.

this is the information showed by "dmesg"

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Fri Jan 12 10:40:27 UTC 2007
    [email protected]:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Mobile AMD Sempron(tm) Processor 3000+ (1794.79-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x20fc2  Stepping = 2

Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  Features2=0x1<SSE3>
  AMD Features=0xc2500800<SYSCALL,NX,MMX+,FFXSR,3DNow+,3DNow>
  AMD Features2=0x1<LAHF>
real memory  = 233766912 (222 MB)
avail memory = 219197440 (209 MB)
ACPI APIC Table: <PTLTD          3091  >
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <HP 3091> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21
acpi0: Power Button (fixed)
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f71280 StartNode 0xc1f71280 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._CRS] (Node 0xc1f71280), AE_NOT_FOUND
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x18> port 0x62,0x66 on acpi0
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f71280 StartNode 0xc1f71280 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._CRS] (Node 0xc1f71280), AE_NOT_FOUND
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f6c160 StartNode 0xc1f6c160 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._PRS] (Node 0xc1f6c160), AE_NOT_FOUND
pci_link8: Unable to parse _CRS or _PRS: AE_NOT_FOUND
device_attach: pci_link8 attach returned 6
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 5.0 (no driver attached)
ohci0: <ATI SB400 USB Controller> mem 0xd0000000-0xd0000fff irq 19 at device
19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <ATI SB400 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1: <ATI SB400 USB Controller> mem 0xd0001000-0xd0001fff irq 19 at device
19.1 on pci0
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <ATI SB400 USB Controller> on ohci1
usb1: USB revision 1.0
uhub1: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
ehci0: <ATI SB400 USB 2.0 controller> mem 0xd0002000-0xd0002fff irq 19 at
device 19.2 on pci0
ehci0: [GIANT-LOCKED]
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <ATI SB400 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci0: <ATI IXP400 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x8410-0x841f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci5: <ACPI PCI bus> on pcib2
rl0: <RealTek 8139 10/100BaseTX> port 0xa000-0xa0ff mem
0xd0206000-0xd02060ff irq 18 at device 0.0 on pci5
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:16:36:18:10:9f
cbb0: <PCI-CardBus Bridge> at device 9.0 on pci5
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem
0xd0206800-0xd0206fff,0xd0200000-0xd0203fff irq 22 at device 9.2 on pci5
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:c0:9f:00:00:85:7a:e2
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:c0:9f:85:7a:e2
fwe0: Ethernet address: 02:c0:9f:85:7a:e2
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=2, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
fwohci0: phy int
pci5: <mass storage> at device 9.3 (no driver attached)
pci5: <base peripheral> at device 9.4 (no driver attached)
pcm0: <ATI IXP 400> mem 0xd0003400-0xd00034ff irq 17 at device 20.5 on pci0
pci0: <simple comms, generic modem> at device 20.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f71280 StartNode 0xc1f71280 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._CRS] (Node 0xc1f71280), AE_NOT_FOUND
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f6c160 StartNode 0xc1f6c160 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._PRS] (Node 0xc1f6c160), AE_NOT_FOUND
pci_link8: Unable to parse _CRS or _PRS: AE_NOT_FOUND
device_attach: pci_link8 attach returned 6
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xcffff,0xd0000-0xd0fff,0xdc000-0xdffff,0xe0000-0xe3fff on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: Logitech USB Receiver, rev 1.10/20.10, addr 2, iclass 3/1
ums0: 16 buttons and Z dir.
Timecounter "TSC" frequency 1794791970 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 38154MB <TOSHIBA MK4025GAS KA101A> at ata0-master UDMA100
acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-4244N/1.02> at ata1-master PIO4
pcm0: <Conexant CX20468-21 AC97 Codec>
Trying to mount root from ufs:/dev/ad0s3a
localhost# exit
exit
$ dmesg
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Fri Jan 12 10:40:27 UTC 2007
    [email protected]:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Mobile AMD Sempron(tm) Processor 3000+ (1794.79-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x20fc2  Stepping = 2

Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  Features2=0x1<SSE3>
  AMD Features=0xc2500800<SYSCALL,NX,MMX+,FFXSR,3DNow+,3DNow>
  AMD Features2=0x1<LAHF>
real memory  = 233766912 (222 MB)
avail memory = 219197440 (209 MB)
ACPI APIC Table: <PTLTD          3091  >
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <HP 3091> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21
acpi0: Power Button (fixed)
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f71280 StartNode 0xc1f71280 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._CRS] (Node 0xc1f71280), AE_NOT_FOUND
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x18> port 0x62,0x66 on acpi0
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f71280 StartNode 0xc1f71280 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._CRS] (Node 0xc1f71280), AE_NOT_FOUND
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f6c160 StartNode 0xc1f6c160 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._PRS] (Node 0xc1f6c160), AE_NOT_FOUND
pci_link8: Unable to parse _CRS or _PRS: AE_NOT_FOUND
device_attach: pci_link8 attach returned 6
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 5.0 (no driver attached)
ohci0: <ATI SB400 USB Controller> mem 0xd0000000-0xd0000fff irq 19 at device
19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <ATI SB400 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1: <ATI SB400 USB Controller> mem 0xd0001000-0xd0001fff irq 19 at device
19.1 on pci0
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <ATI SB400 USB Controller> on ohci1
usb1: USB revision 1.0
uhub1: ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
ehci0: <ATI SB400 USB 2.0 controller> mem 0xd0002000-0xd0002fff irq 19 at
device 19.2 on pci0
ehci0: [GIANT-LOCKED]
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <ATI SB400 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci0: <ATI IXP400 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x8410-0x841f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci5: <ACPI PCI bus> on pcib2
rl0: <RealTek 8139 10/100BaseTX> port 0xa000-0xa0ff mem
0xd0206000-0xd02060ff irq 18 at device 0.0 on pci5
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:16:36:18:10:9f
cbb0: <PCI-CardBus Bridge> at device 9.0 on pci5
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem
0xd0206800-0xd0206fff,0xd0200000-0xd0203fff irq 22 at device 9.2 on pci5
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:c0:9f:00:00:85:7a:e2
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:c0:9f:85:7a:e2
fwe0: Ethernet address: 02:c0:9f:85:7a:e2
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc000ffc0, gen=2, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
fwohci0: phy int
pci5: <mass storage> at device 9.3 (no driver attached)
pci5: <base peripheral> at device 9.4 (no driver attached)
pcm0: <ATI IXP 400> mem 0xd0003400-0xd00034ff irq 17 at device 20.5 on pci0
pci0: <simple comms, generic modem> at device 20.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f71280 StartNode 0xc1f71280 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._CRS] (Node 0xc1f71280), AE_NOT_FOUND
    ACPI-0438: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND
SearchNode 0xc1f6c160 StartNode 0xc1f6c160 ReturnNode 0
    ACPI-1304: *** Error: Method execution failed
[\\_SB_.PCI0.LPC0.LNKU._PRS] (Node 0xc1f6c160), AE_NOT_FOUND
pci_link8: Unable to parse _CRS or _PRS: AE_NOT_FOUND
device_attach: pci_link8 attach returned 6
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xcffff,0xd0000-0xd0fff,0xdc000-0xdffff,0xe0000-0xe3fff on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: Logitech USB Receiver, rev 1.10/20.10, addr 2, iclass 3/1
ums0: 16 buttons and Z dir.
Timecounter "TSC" frequency 1794791970 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 38154MB <TOSHIBA MK4025GAS KA101A> at ata0-master UDMA100
acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-4244N/1.02> at ata1-master PIO4
pcm0: <Conexant CX20468-21 AC97 Codec>
Trying to mount root from ufs:/dev/ad0s3a
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"