Re: if_wpi will not work for me

Hello Gary,

Everything looks reasonable. Attached is a collection of data on my
setup (note driver version is quite old!!!). Have no chance yet to try
with newer one.

There is an ambiguity in wpa_supplicant and rc.conf settings, but I
gave both configs just to be fair. AFAIU, rc.conf is used ATM.

Also note, that I have no AP at work, so device is not associated in
the logs. But it does work at home.

2008/3/20, [email protected] <[email protected]>:
> > My notebook is HP Compaq nc2400 running FreeBSD 7.0-RELEASE
>  >
>  > kldload if_wpi give me
>  > Mar 18 10:29:34 juba kernel: wpi0: <Intel(R) PRO/Wireless 3945ABG> mem
>  > 0xf0000000-0xf0000fff irq 16 at device 0.0 on pci8
>  > Mar 18 10:29:34 juba kernel: wpi0: could not allocate memory resource
>  > Mar 18 10:29:34 juba kernel: device_attach: wpi0 attach returned 6
>  >
>  > and ifconfig show no wpi0
>  >
>  > I have not seen this behaviour mentioned before, so could anyone
>  > give me some hints, please?
>  >
>
> > mvh
>  >
>  > johan
>
>  I have been describing related problems in a different thread, but it might
>  help others if I join this one.
>
>  Before I go on, a big mahalo (thanks) to everyone with advice on how to get
>  my Lucent Gold wifi card working better. Much better now.
>
>  My Dell Latitude D830 has a built-in wifi interface which Dennis Melentyev
>  said might work with the wpi driver. I followed his advice and the
>  instructions on the wpi man page, but no luck yet.
>
>  Here is my entire /boot/loader.conf file, which includes stuff for the
>  sound card (which does not send output through the built-in speakers, which
>  is not much of a loss).
>
>  sound_load="YES"
>  snd_hda_load="YES"
>  # enable ATAPI/CAM driver for CD-ROM
>  atapicam_load="YES"
>  # enable wpi wireless driver for Dell internal
>  legal.intel_wpi.license_ack=1
>  if_wpi_load="YES"
>  wlan_load="YES"
>  wlan_amrr_load="YES"
>  firmware_load="YES"
>  wpifw_load="YES"
>
>  Does it matter what sequence these come in?
>
>  Here the output of kldstat:
>
>  Id Refs Address    Size     Name
>   1   19 0xc0400000 926ed4   kernel
>   2    2 0xc0d27000 4a5ac    sound.ko
>   3    1 0xc0d72000 14324    snd_hda.ko
>   4    1 0xc0d87000 4d20     atapicam.ko
>   5    1 0xc0d8c000 f140     if_wpi.ko
>   6    1 0xc0d9c000 25f60    wpifw.ko
>   7    1 0xc0dc2000 6a1c4    acpi.ko
>   8    1 0xc5987000 22000    linux.ko
>
>  I noticed some things not listed, wlan, wlan_amrr, and firmware. Just for
>  fun I tried loading them manually, and got this:
>
>  # kldload wlan.ko
>  kldload: can't load wlan.ko: File exists
>
>  The other two, wlan_amrr, and firmware, do the same. I suspect that means
>  those modules are configured into the kernel. ???
>
>  When the system boots I see no sign of activity from wpi0. It does not
>  appear in /var/run/dmesg.boot or /var/log/messages. Is there a log file for
>  loader.conf?
>
>  The computer has an LED that is on in Windows (it comes on about half way
>  through the boot sequence), but remains off when I boot into FreeBSD from
>  power-on. The slider switch on the side of the computer does not switch on
>  the radio. If I go into Windows, then restart and select FreeBSD, the LED
>  remains on but with no change, still nothing in the logs or in the output
>  of ifconfig.
>
>  I can load and unload if_wpi without error.
>
>  I added this to /etc/rc.conf:
>
>  network_interfaces=bge0 wi0 wpi0
>
>  to try to force recognition of wpi0 but no change. (bge0 is the built-in
>  wired Ethernet NIC.)
>
>  Any suggestions?
>
>  Gary Dunn
>  Open Slate Project
>
>
>
>  _______________________________________________
>  [email protected] mailing list
>  http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
>  To unsubscribe, send any mail to "[email protected]"
>


-- 
Dennis Melentyev

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"