Re: fprint (finger print sensor framework) port ready for testing

Yupp I even set the permissions 777 and added the user i tested to group
operator.... still no joy
ive used the upek port no problems even with GDM. the "root" user works
great, but regular users cant even register

ls -al /dev/ugen*
crw-rw-rw-  1 root  operator    0,  84 Apr 15 14:14 /dev/ugen0
crw-rw-rw-  1 root  operator    0,  85 Apr 15 14:14 /dev/ugen0.1
crw-rw-rw-  1 root  operator    0,  86 Apr 15 14:14 /dev/ugen0.2
crw-rw-rw-  1 root  operator    0,  87 Apr 15 14:14 /dev/ugen0.3
crw-rw-rw-  1 root  operator    0,  88 Apr 15 14:14 /dev/ugen0.4
crwxrwxrwx  1 root  operator    0,  89 Apr 15 14:14 /dev/ugen1
crwxrwxrwx  1 root  operator    0,  90 Apr 15 14:14 /dev/ugen1.1
crwxrwxrwx  1 root  operator    0,  91 Apr 16 01:34 /dev/ugen1.2
crwxrwxrwx  1 root  operator    0,  92 Apr 15 14:14 /dev/ugen1.3

usbdevs -vd
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
  uhub0
 port 1 powered
 port 2 addr 2: low speed, power 98 mA, config 1, USB Receiver(0xc521),
Logitech(0x046d), rev 57.00
   ums0
   uhid0
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
  uhub1
 port 1 powered
 port 2 powered
Controller /dev/usb2:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
  uhub2
 port 1 addr 2: full speed, self powered, config 1, BCM2045B(0x2110),
Broadcom Corp(0x0a5c), rev 1.00
   ugen0
 port 2 addr 3: full speed, power 100 mA, config 1, Biometric
Coprocessor(0x2016), STMicroelectronics(0x0483), rev 0.01
   ugen1
Controller /dev/usb3:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x0000), rev 1.00
  uhub3
 port 1 powered
 port 2 powered
Controller /dev/usb4:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
Intel(0x0000), rev 1.00
  uhub4
 port 1 powered
 port 2 powered
 port 3 powered
 port 4 powered
 port 5 powered
 port 6 powered
 port 7 powered
 port 8 powered




On Wed, Apr 16, 2008 at 2:43 AM, Simon Barner <[email protected]> wrote:

> Outback Dingo wrote:
> > pam_fprint works (see below) but when i try to run the fprint demo i get
> >
> > STATUS: No Devices Found
>
> Are you sure you have r/w access to the sensor's USB device?
> >
> > pam_fprint_enroll -f 7
> > This program will enroll your finger, unconditionally overwriting any
> selected
> > print that was enrolled previously. If you want to continue, press
> enter,
> > otherwise hit Ctrl+C
> >
> > Found device claimed by UPEK TouchStrip driver
> > Opened device. It's now time to enroll your finger.
> >
> > You will need to successfully scan your Right Index Finger 3 times to
> complete
> > the process.
> >
> > Scan your finger now.
> > upekts:error [read_msg] non-zero bytes in cmd response
> > upekts:error [read_msg28] expected response, got -1 seq=40
>
> Something seems to go wrong. I have never seenn this error message.
>
> Which sensor are you using? Can you send me the output of `usbdevs -vd'
> in a private mail please?
>
> --
> Best regards / Viele Grüße,                             [email protected]
>  Simon Barner                                                [email protected]
>
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"