Re: ath: unable to attach hardware; HAL status 3; attach returned 6
Ian <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
That sounds like a fairly accurate assessment of the issue. The only thing that makes me hesitate is that based on a report I have read (http://mjoc.sig.lt/papers/freebsd/vaio/vaio_freebsd.html); There where no problems with the PCMCIA when he installed freeBSD 5.3. So I guess the questions after this point go in this order: 1. Could something have changed from 5.3 to 7.0 that would have stopped it from working? 2. The cardbus on the working system is a Micro, Inc. The vaio is a Ricoh Co chipset (both according to lspci). So this may indicate that the issue may lie in the cardbus. Where can I find the work being done on the support? 3. If this does not correct the issue, could it be from a physical breakage? Thank you for your attention. On Wed, Aug 13, 2008 at 11:54 AM, Sam Leffler <[email protected]> wrote: > This is likely a cardbus issue. The hal status code is: > > HAL_EIO = 3, /* Hardware didn't respond as expected */ > > (look in sys/contrib/dev/ath/ah.h) and it typically means the sanity > check/self test done at startup failed. > > For fun you might check if the cardbus chip on the two laptops are > different. Warner just recently fixed some cardbus issues in HEAD (w/ Ricoh > bridge chips I believe) but the symptoms were different. > > Sam > > Ian wrote: > >> I am running the latest ath_hal from http://people.freebsd.org/~sam/<http://people.freebsd.org/%7Esam/> >> >> I likely should have mentioned that in the first place >> >> The wireless card is picked up fine when I move the harddrive to another >> laptop. Which >> would likely rule out the possibility that the issue is within the chipset >> (unless I am >> severely misguided, which I won't rule out). >> >> Also I am running a generic kernel of FreeBSD-7.0 STABLE (though the issue >> was still there when >> I had RELEASE running) >> >> >> On Wed, Aug 13, 2008 at 5:25 AM, Ashish Shukla आशीष शॠकॠ>> ल <wahjava.ml@ >> gmail.com> wrote: >> >> >> >>> Ian writes: >>> >>> >>>> Goal: >>>> to have Wireless Atheros based NIC run on my Sony Vaio >>>> Background: >>>> The computer in question is a Sony Vaio PCG R505-JL w/ slimdock. >>>> The >>>> >>>> >>> CD-ROM >>> >>> >>>> is broken. >>>> I used a second computer and installed it on the second computer, then >>>> transfered the >>>> hard drive to the vaio. >>>> This problem is not present on the computer I installed it on. The >>>> card >>>> works Out-of box. >>>> dmesg output: >>>> >>>> >>> [snip] >>> >>> >>> >>>> ath0: <Atheros 2413> mem 0xf4110000-0xf411ffff irq 9 at device 0.0 on >>>> cardbus0 >>>> ath0: [ITHREAD] >>>> ath0: unable to attach hardware; HAL status 3 >>>> device_attach: ath0 attach returned 6 >>>> >>>> >>> Above output indicates, wireless chip not accepting the HAL >>> firmware. You can try the latest HAL available from following URL: >>> >>> http://people.freebsd.org/~sam/ath_hal-20080528.tgz<http://people.freebsd.org/%7Esam/ath_hal-20080528.tgz> >>> <http://people.freebsd.org/%7Esam/ath_hal-20080528.tgz> >>> >>> HTH >>> Ashish Shukla >>> -- >>> ·-- ·- ···· ·--- ·- ···- ·- ·--·-· --· -- ·- ·· >>> ·-·· ·-·-·- -·-· --- -- >>> >>> >>> ------------------------------------------------------------------------ >>> >>> _______________________________________________ >>> [email protected] mailing list >>> http://lists.freebsd.org/mailman/listinfo/freebsd-mobile >>> To unsubscribe, send any mail to "[email protected] >>> " >>> >> > _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-mobile To unsubscribe, send any mail to "[email protected]"