New Media Bus Toaster - trouble !
Mike Tarasov <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
Hi All!
People, please help, tell me where bug?
dmesg.boot
__________
pcic0: <TI PCI-1211 PCI-CardBus Bridge> mem 0x41180000-0x41180fff irq 11
at device 4.0 on pci0
pcic0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pccard0: <PC Card bus (classic)> on pcic0
___________
/etc/pccard.rc
______________
# NewMedia Bustoaster SCSI
card "PCMCIA Bus Toaster" "SCSI Adapter"
config 0x1 "aic" 10
reset 10000
insert camcontrol rescan all
debuglevel 4
io 0x240-0x360
irq 5 10
memory 0xd4000 96k
______________
pccardc dumpcis
_______________
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: da 00 ff
Common memory device information:
Device number 1, type Function specific, WPS = ON
Speed = 200nS, Memory block size = 512b, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 3
000: 4b 01 ff
Attribute memory device information:
Device number 1, type EEPROM, WPS = ON
Speed = 150nS, Memory block size = 2Kb, 1 units
Tuple #3, code = 0x20 (Manufacturer ID), length = 5
000: cd 10 01 00 ff
PCMCIA ID = 0x10cd, OEM ID = 0x1
Tuple #4, code = 0x21 (Functional ID), length = 3
000: 08 00 ff
SCSI card
Tuple #5, code = 0x15 (Version 1 info), length = 35
000: 05 00 50 43 4d 43 49 41 20 42 75 73 20 54 6f 61
010: 73 74 65 72 00 53 43 53 49 20 41 64 61 70 74 65
020: 72 00 ff
Version = 5.0, Manuf = [PCMCIA Bus Toaster], card vers = [SCSI
Adapter]
Tuple #6, code = 0x1a (Configuration map), length = 5
000: 01 01 f0 03 03
Reg len = 2, config register addr = 0x3f0, last config = 0x1
Registers: XX------
Tuple #7, code = 0x1b (Configuration entry), length = 23
000: c1 c1 bd 7f 55 c5 4b d5 19 36 36 3e 1e e8 14 0f
010: 45 30 ff ff 08 00 00
Config index = 0x1(default)
Interface byte = 0xc1 (I/O) +RDY/-BSY active, wait signal
supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4 x 1V, ext = 0x4b
Maximum operating supply voltage: 5 x 1V, ext = 0x19
Continuous supply current: 3 x 100mA
Max current average over 1 second: 3 x 100mA
Max current average over 10 ms: 3.5 x 100mA
Power down supply current: 1.5 x 100mA
Wait scale Speed = 1.2 x 10 us
RDY/BSY scale Speed = 1.0 x 10 ms, scaled by 100
Card decodes 5 address lines, limited 8/16 Bit I/O
IRQ modes: Level
IRQs: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Memory space length = 0x8
Max twin cards = 0
Misc attr:
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 04 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x400 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 06 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x600 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 08 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x800 block length = 0x20
Tuple #11, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 0a 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0xa00 block length = 0x20
Tuple #12, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 0c 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0xc00 block length = 0x20
Tuple #13, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 0e 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0xe00 block length = 0x20
Tuple #14, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 10 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x1000 block length = 0x20
Tuple #15, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 12 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x1200 block length = 0x20
Tuple #16, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 14 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x1400 block length = 0x20
Tuple #17, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 16 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x1600 block length = 0x20
Tuple #18, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 18 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x1800 block length = 0x20
Tuple #19, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 1a 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x1a00 block length = 0x20
Tuple #20, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 1c 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x1c00 block length = 0x20
Tuple #21, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 1e 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x1e00 block length = 0x20
Tuple #22, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 20 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x2000 block length = 0x20
Tuple #23, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 22 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x2200 block length = 0x20
Tuple #24, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 24 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x2400 block length = 0x20
Tuple #25, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 26 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x2600 block length = 0x20
Tuple #26, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 28 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x2800 block length = 0x20
Tuple #27, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 2a 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x2a00 block length = 0x20
Tuple #28, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 2c 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x2c00 block length = 0x20
Tuple #29, code = 0x1b (Configuration entry), length = 7
000: 01 08 ca 60 00 2e 1f
Config index = 0x1
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x2e00 block length = 0x20
Tuple #30, code = 0x14 (No link), length = 1
000: ff
Tuple #31, code = 0xff (Terminator), length = 0
1 slots found
_____________
And what i'm have.
Aug 8 10:20:09 evo /kernel: pccard: card inserted, slot 0
Aug 8 10:20:15 evo pccardd[52]: Card "PCMCIA Bus Toaster"("SCSI
Adapter") [(null)] [(null)] matched "PCMCIA Bus Toaster" ("SCSI
Adapter") [(null)] [(null)]
Aug 8 10:20:15 evo pccardd[52]: Found existing driver (aic) for PCMCIA
Bus Toaster
Aug 8 10:20:15 evo pccardd[52]: Using mem addr 0xd4000, size 2048, card
addr 0x0, flags 0x41
Aug 8 10:20:15 evo pccardd[52]: Using I/O addr 0x240, size 32
Aug 8 10:20:15 evo pccardd[52]: Setting config reg at offs 0x3f0 to
0x41, Reset time = 10000 ms
Aug 8 10:20:30 evo pccardd[52]: Assigning I/O window 0, start 0x240,
size 0x20 flags 0x5
Aug 8 10:20:30 evo pccardd[52]: Assign aic0, io 0x240-0x25f, mem
0xd4000, 2048 bytes, irq 11, flags 0
Aug 8 10:20:30 evo pccardd[52]: driver allocation failed for PCMCIA Bus
Toaster(SCSI Adapter): Device not configured
_____________
Best regards,
Mike Tarasov
To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message