Problem to configure Linksys EtherFast 10&100 + 56K PC Card

Hi, I am installing FreeBSD 4.6-stable on my Sony Vaio F680K notebook. I have difficulty to configure the Linksys EtherFast 10&100 + 56K PC card (PCMLM56). The following error message is shown:

Aug 11 10:29:30  pccardd[157]: Card "Linksys"("EtherFast 10&100 + 56K PC Card (PCMLM56)") [(null)] [(null)] matched "Linksys" ("EtherFast 10&100 + 56K PC Card (PCMLM56)") [(null)] [(null)]
Aug 11 10:29:30  pccardd[157]: Using I/O addr 0x2f8, size 8
Aug 11 10:29:30  pccardd[157]: Using I/O addr 0x300, size 32
Aug 11 10:29:30  pccardd[157]: Setting config reg at offs 0xffe0 to 0x43, Reset time = 1000 ms
Aug 11 10:29:36  pccardd[157]: Assigning I/O window 0, start 0x2f8, size 0x8 flags 0x7
Aug 11 10:29:36  pccardd[157]: Assigning I/O window 1, start 0x300, size 0x20 flags 0x7
Aug 11 10:29:36  pccardd[157]: Assign ed0, io 0x2f8-0x2ff, mem 0x0, 0 bytes, irq 9, flags 0x7
Aug 11 10:29:36  pccardd[157]: driver allocation failed for Linksys(EtherFast 10&100 + 56K PC Card (PCMLM56)): Device not configured
Aug 11 10:29:36  pccardd[157]: pccardd started

The /etc/pccard.conf is:
debuglevel 4

# Linksys PCMLM56
card "Linksys" "EtherFast 10&100 + 56K PC Card (PCMLM56)"
        config  0x3 "ed" 3 7
        insert  /etc/pccard_ether $device start
        remove  /etc/pccard_ether $device stop
        reset 1000

Since the configuration of this card in Windows shows io 0x300, mem 0xde000 and irq 3, I set the pccard.conf to irq 3, but it does not have any effect. The memory address also has problem too. I also tried to disable plug'nplay in BIOS, but the result is the same. Below is the result of dmesg | grep irq and the pccardc dumpcis. 

Does anybody know what the problem is?

Regards,
Calvin

dmesg | grep irq:
pci1: <ATI Mobility-1 graphics accelerator> at 0.0 irq 9
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xfca0-0xfcbf irq 9 at
device 7.2 on pci0
pci0: <unknown card> (vendor=0x104d, dev=0x8039) at 8.0 irq 9
pci0: <unknown card> (vendor=0x1073, dev=0x0010) at 9.0 irq 9
pci0: <unknown card> (vendor=0x14f1, dev=0x2443) at 10.0 irq 9
pci_cfgintr_linked: linked (60) to hard-routed irq 9
pci_cfgintr: 0:12 INTA routed to irq 9
pcic0: <Ricoh RL5C478 PCI-CardBus Bridge> irq 9 at device 12.0 on pci0
pci_cfgintr_linked: linked (61) to hard-routed irq 9
pci_cfgintr: 0:12 INTB routed to irq 9
pcic1: <Ricoh RL5C478 PCI-CardBus Bridge> irq 9 at device 12.1 on pci0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0

Below is the pccardc dumpcis:

Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
    000:  00 ff
 Common memory device information:
  Device number 1, type No device, WPS = OFF
  Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x15 (Version 1 info), length = 52
    000:  04 01 4c 69 6e 6b 73 79 73 00 45 74 68 65 72 46
    010:  61 73 74 20 31 30 26 31 30 30 20 2b 20 35 36 4b
    020:  20 50 43 20 43 61 72 64 20 28 50 43 4d 4c 4d 35
    030:  36 29 00 ff
 Version = 4.1, Manuf = [Linksys], card vers = [EtherFast 10&100 + 56K PC
Card (PCMLM56)]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
    000:  43 01 ab c0
 PCMCIA ID = 0x143, OEM ID = 0xc0ab
Tuple #4, code = 0x21 (Functional ID), length = 2
    000:  00 00
 Multifunction card
Tuple #5, code = 0x1a (Configuration map), length = 5
    000:  01 1b e0 ff 67
 Reg len = 2, config register addr = 0xffe0, last config = 0x1b
 Registers: XXX--XX-
Tuple #6, code = 0x1b (Configuration entry), length = 22
    000:  c3 41 99 79 55 3d 86 46 26 4c ea 61 f8 02 07 00
    010:  03 1f f0 38 9e 28
 Config index = 0x3(default)
 Interface byte = 0x41 (I/O)  +RDY/-BSY active
 Vcc pwr:
  Nominal operating supply voltage: 5 x 1V
  Continuous supply current: 3.5 x 10mA
  Max current average over 1 second: 1 x 100mA, ext = 0x46
  Max current average over 10 ms: 2 x 100mA
  Power down supply current: 4.5 x 1mA
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2f8 block length = 0x8
  I/O address # 2: block start = 0x300 block length = 0x20
  IRQ modes: Level, Pulse, Shared
  IRQs:  3 4 5 9 10 11 12 15
 Max twin cards = 0
 Misc attr: (Audio-BVD2) (Power down supported)
Tuple #7, code = 0x1b (Configuration entry), length = 10
    000:  05 08 ea 61 e8 03 07 00 03 1f
 Config index = 0x5
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x3e8 block length = 0x8
  I/O address # 2: block start = 0x300 block length = 0x20
Tuple #8, code = 0x1b (Configuration entry), length = 10
    000:  07 08 ea 61 e8 02 07 00 03 1f
 Config index = 0x7
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2e8 block length = 0x8
  I/O address # 2: block start = 0x300 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 10
    000:  09 08 ea 61 f8 02 07 20 03 1f
 Config index = 0x9
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2f8 block length = 0x8
  I/O address # 2: block start = 0x320 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 10
    000:  0b 08 ea 61 e8 03 07 20 03 1f
 Config index = 0xb
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x3e8 block length = 0x8
  I/O address # 2: block start = 0x320 block length = 0x20
Tuple #11, code = 0x1b (Configuration entry), length = 10
    000:  0d 08 ea 61 e8 02 07 20 03 1f
 Config index = 0xd
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2e8 block length = 0x8
  I/O address # 2: block start = 0x320 block length = 0x20
Tuple #12, code = 0x1b (Configuration entry), length = 10
    000:  0f 08 ea 61 f8 02 07 40 03 1f
 Config index = 0xf
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2f8 block length = 0x8
  I/O address # 2: block start = 0x340 block length = 0x20
Tuple #13, code = 0x1b (Configuration entry), length = 10
    000:  11 08 ea 61 e8 03 07 40 03 1f
 Config index = 0x11
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x3e8 block length = 0x8
  I/O address # 2: block start = 0x340 block length = 0x20
Tuple #14, code = 0x1b (Configuration entry), length = 10
    000:  13 08 ea 61 e8 02 07 40 03 1f
 Config index = 0x13
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2e8 block length = 0x8
  I/O address # 2: block start = 0x340 block length = 0x20
Tuple #15, code = 0x1b (Configuration entry), length = 10
    000:  15 08 ea 61 f8 02 07 20 02 1f
 Config index = 0x15
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2f8 block length = 0x8
  I/O address # 2: block start = 0x220 block length = 0x20
Tuple #16, code = 0x1b (Configuration entry), length = 10
    000:  17 08 ea 61 e8 03 07 20 02 1f
 Config index = 0x17
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x3e8 block length = 0x8
  I/O address # 2: block start = 0x220 block length = 0x20
Tuple #17, code = 0x1b (Configuration entry), length = 10
    000:  19 08 ea 61 e8 02 07 20 02 1f
 Config index = 0x19
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2e8 block length = 0x8
  I/O address # 2: block start = 0x220 block length = 0x20
Tuple #18, code = 0x1b (Configuration entry), length = 10
    000:  1b 08 ea 61 f8 02 07 40 02 0f
 Config index = 0x1b
 Card decodes 10 address lines, full 8/16 Bit I/O
  I/O address # 1: block start = 0x2f8 block length = 0x8
  I/O address # 2: block start = 0x240 block length = 0x10
Tuple #19, code = 0xff (Terminator), length = 0