Re: pcmcia modem

On Sun, Aug 18, 2002 at 12:33:39PM +0200, Emanuel Haupt wrote:

> > > > 3rd: Can you communicate with your modem using cu/ecu?
> > > 
> > > cu -l /dev/cuaa4 -s 9600
> > > freezes freebsd completely!
> > > 
> 
> 
> its freebsd 5.0-DP1. i am using the NEWCARD kernel because
> sometimes i need other cards: ethernetcard, wireless card. but
> while that "irq trouble" happens there is no other pcmcia card
> inserted.

Actually, I never tried NEWCARD kernel yet.
The only 5.0-DP1 I have is my desktop, my notebook is 4.6-STABLE.
So it's better to address your question to M. Warner Losh,
I see lines that might describe problem, but I don't know the meaning:

> pccard1: Allocation failed for cfe 32
> pccard1: Allocation failed for cfe 33

> 
> it might help you to see my whole dmesg output:
> 
> Copyright (c) 1992-2002 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992,
> 1993, 1994
> 	The Regents of the University of California. All rights
> reserved.
> FreeBSD 5.0-DP1 #0: Fri Jul 26 10:40:11 CEST 2002
>     root@:/usr/src/sys/i386/compile/DEEDEE
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc0570000.
> Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05700a8.
> Timecounter "i8254"  frequency 1193182 Hz
> Timecounter "TSC"  frequency 498470138 Hz
> CPU: Pentium III/Pentium III Xeon/Celeron (498.47-MHz
> 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0x686  Stepping = 6
>  
> Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTR
> R,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> real memory  = 134066176 (130924K bytes)
> avail memory = 124407808 (121492K bytes)
> Pentium Pro MTRR support enabled
> Using $PIR table, 6 entries at 0xc00fbd20
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> acpi0: <DELL   CPi R  > on motherboard
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> ACPI timer looks BAD  min = 2, max = 6, width = 5
> Timecounter "ACPI-safe"  frequency 3579545 Hz
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on
> acpi0
> acpi_cpu0: <CPU> on acpi0
> acpi_tz0: <thermal zone> on acpi0
> acpi_acad0: <AC adapter> on acpi0
> acpi_cmbat0: <Control method Battery> on acpi0
> acpi_cmbat1: <Control method Battery> on acpi0
> acpi_lid0: <Control Method Lid Switch> on acpi0
> acpi_button0: <Power Button> on acpi0
> acpi_button1: <Sleep Button> on acpi0
> acpi_pcib0: <Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <PCI bus> on acpi_pcib0
> pcib1: <PCI-PCI bridge> at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> pci1: <display, VGA> at device 0.0 (no driver attached)
> pccbb0: <TI1225 PCI-CardBus Bridge> at device 3.0 on pci0
> cardbus0: <CardBus bus> on pccbb0
> pccard0: <16-bit PCCard bus> on pccbb0
> acpi_pcib0: device is routed to IRQ 11
> pccbb1: <TI1225 PCI-CardBus Bridge> at device 3.1 on pci0
> cardbus1: <CardBus bus> on pccbb1
> pccard1: <16-bit PCCard bus> on pccbb1
> acpi_pcib0: device is routed to IRQ 11
> isab0: <PCI-ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel PIIX4 ATA33 controller> port 0x860-0x86f at
> device 7.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port
> 0xdce0-0xdcff irq 11 at device 7.2 on pci0
> usb0: cannot stop
> usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
> pci0: <multimedia, audio> at device 8.0 (no driver attached)
> atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on
> acpi0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model GlidePoint, device ID 0
> fdc0: <enhanced floppy controller (i82077, NE72065 or clone)>
> port 0x3f7,0x3f2-0x3f5 irq 6 on acpi0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> sio0 port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> sio1 port 0x280-0x287,0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> ppc0 port 0x778-0x77b,0x378-0x37f irq 7 on acpi0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/8 bytes threshold
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
> pmtimer0 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
> 0xa0000-0xbffff on isa0
> system power profile changed to 'economy'
> wi0: <WaveLAN/IEEE> at port 0x100-0x13f irq 11 function 0
> config 1 on pccard0
> wi0: 802.11 address: 00:90:d1:07:b0:64
> wi0: using RF:PRISM2 MAC:HFA3841 CARD:HWB3163 rev.A, Firmware:
> 1.4 variant 9
> pccard1: Allocation failed for cfe 32
> pccard1: Allocation failed for cfe 33
> ed1: Total wildcard entry ignored for SVEC PN650TX 10/100 Dual
> Speed Fast Ethernet PC Card
> sio4 at port 0x3e8-0x3ef irq 11 function 0 config 34 on
> pccard1
> sio4: type 16550A
> sio4: unable to activate interrupt in fast mode - using normal
> mode
> ad0: 19077MB <IBM-DJSA-220> [38760/16/63] at ata0-master
> UDMA33
> acd0: CDROM <SAMSUNG CD-ROM SN-124> at ata1-master PIO4
> Mounting root from ufs:/dev/ad0s1a

-- 
BR,
Kirill Bezzubets                                CASE-RIPE CASE-RIPN
Senior Administrator, Technical Department      mailto:[email protected]
Solaris ISP & Telecommunications Co. Ltd        http://www.solaris.ru

To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message