Nokia D211 GSM/HSCD/GPRS/802.11 multifunction card

Hello,

Has anybody got the Nokia D211 multifunction card to work with FreeBSD? 
The card is a combined cell phone (with GSM/HSCD/GPRS) and 802.11.
  http://www.nokia.com/phones/nokiad211/specifications.html

I am at first intrerested in getting the GPRS functions to work. Entering 
the card as a serial device (as in generic PCMCIA MODEM, which works with 
Nokia's other card phones) in pccard.conf and then tryping to connect with 
"tip" brings my system (4.6R) to a complete lockup. Nokia claims that the 
card is supported under Linux.

The output from "pccardc dumpcis" is attached below. Any ideas on how to 
configure this beast??

With kind regards,

--Borje

Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
    000:  00 00 ff
	Common memory device information:
		Device number 1, type No device, WPS = OFF
		Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x15 (Version 1 info), length = 14
    000:  07 00 4e 6f 6b 69 61 00 44 32 31 31 00 ff
	Version = 7.0, Manuf = [Nokia], card vers = [D211]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
    000:  24 01 20 11
	PCMCIA ID = 0x124, OEM ID = 0x1120
Tuple #4, code = 0x21 (Functional ID), length = 2
    000:  06 00
	Network/LAN adapter
Tuple #5, code = 0x22 (Functional EXT), length = 2
    000:  01 07
	Network technology: Wireless
Tuple #6, code = 0x22 (Functional EXT), length = 5
    000:  02 c0 d8 a7 00
	Network speed: 11 Mb/sec
Tuple #7, code = 0x22 (Functional EXT), length = 2
    000:  03 07
	Network media: 2.4 GHz
Tuple #8, code = 0x1a (Configuration map), length = 4
    000:  00 01 f4 01
	Reg len = 1, config register addr = 0xf4, last config = 0x1
	Registers: X------- 
Tuple #9, code = 0x1b (Configuration entry), length = 19
    000:  c1 01 1e 71 55 36 c6 5a 35 01 8e 7f e5 13 5f 64
    010:  30 ff ff
	Config index = 0x1(default)
	Interface byte = 0x1 (I/O)
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Max current average over 1 second: 3 x 100mA
		Max current average over 10 ms: 4 x 100mA, ext = 0x5a
		Power down supply current: 3 x 10mA
	Vpp pwr:
		Nominal operating supply voltage: 1.2 x 10V, ext = 0x7f
	Wait scale Speed = 1.2 x 1 us, scaled by 10
	RDY/BSY scale Speed = 5.0 x 10 ms, scaled by 10
	Card decodes 4 address lines, full 8/16 Bit I/O
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Tuple #10, code = 0x14 (No link), length = 0
Tuple #11, code = 0xff (Terminator), length = 0



To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message