Re: Nokia D211 GSM/HSCD/GPRS/802.11 multifunction card

Hello,

So far, I haven't got any answers - so I guess that noone has yet tried 
this card under FreeBSD, so I have made some more tests. Since I haven't 
previously delt with multifunction cards, I really don't have a clue where 
to go next. The FAQ and the handbook does not mention this. I have tried 
changning the "config" line in pccard.conf to "auto", "default", "0x1". 
All of theese give the same hangning result.

Any ideas on what to try next? I can install the card under Windows, but 
don't know what to look for there.

--Börje

On Mon, 19 Aug 2002 18:52:19 +0200 Borje Josefsson wrote:

> 
> Hello,
> 
> Has anybody got the Nokia D211 multifunction card to work with FreeBSD? 
> The card is a combined cell phone (with GSM/HSCD/GPRS) and 802.11.
>   http://www.nokia.com/phones/nokiad211/specifications.html
> 
> I am at first intrerested in getting the GPRS functions to work. Entering 
> the card as a serial device (as in generic PCMCIA MODEM, which works with 
> Nokia's other card phones) in pccard.conf and then tryping to connect with 
> "tip" brings my system (4.6R) to a complete lockup. Nokia claims that the 
> card is supported under Linux.
> 
> The output from "pccardc dumpcis" is attached below. Any ideas on how to 
> configure this beast??
> 
> With kind regards,
> 
> --Borje
> 
> Configuration data for card in slot 0
> Tuple #1, code = 0x1 (Common memory descriptor), length = 3
>     000:  00 00 ff
> 	Common memory device information:
> 		Device number 1, type No device, WPS = OFF
> 		Speed = No speed, Memory block size = 512b, 1 units
> Tuple #2, code = 0x15 (Version 1 info), length = 14
>     000:  07 00 4e 6f 6b 69 61 00 44 32 31 31 00 ff
> 	Version = 7.0, Manuf = [Nokia], card vers = [D211]
> Tuple #3, code = 0x20 (Manufacturer ID), length = 4
>     000:  24 01 20 11
> 	PCMCIA ID = 0x124, OEM ID = 0x1120
> Tuple #4, code = 0x21 (Functional ID), length = 2
>     000:  06 00
> 	Network/LAN adapter
> Tuple #5, code = 0x22 (Functional EXT), length = 2
>     000:  01 07
> 	Network technology: Wireless
> Tuple #6, code = 0x22 (Functional EXT), length = 5
>     000:  02 c0 d8 a7 00
> 	Network speed: 11 Mb/sec
> Tuple #7, code = 0x22 (Functional EXT), length = 2
>     000:  03 07
> 	Network media: 2.4 GHz
> Tuple #8, code = 0x1a (Configuration map), length = 4
>     000:  00 01 f4 01
> 	Reg len = 1, config register addr = 0xf4, last config = 0x1
> 	Registers: X------- 
> Tuple #9, code = 0x1b (Configuration entry), length = 19
>     000:  c1 01 1e 71 55 36 c6 5a 35 01 8e 7f e5 13 5f 64
>     010:  30 ff ff
> 	Config index = 0x1(default)
> 	Interface byte = 0x1 (I/O)
> 	Vcc pwr:
> 		Nominal operating supply voltage: 5 x 1V
> 		Max current average over 1 second: 3 x 100mA
> 		Max current average over 10 ms: 4 x 100mA, ext = 0x5a
> 		Power down supply current: 3 x 10mA
> 	Vpp pwr:
> 		Nominal operating supply voltage: 1.2 x 10V, ext = 0x7f
> 	Wait scale Speed = 1.2 x 1 us, scaled by 10
> 	RDY/BSY scale Speed = 5.0 x 10 ms, scaled by 10
> 	Card decodes 4 address lines, full 8/16 Bit I/O
> 		IRQ modes: Level
> 		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
> Tuple #10, code = 0x14 (No link), length = 0
> Tuple #11, code = 0xff (Terminator), length = 0
> 
> 
> 
> To Unsubscribe: send mail to [email protected]
> with "unsubscribe freebsd-mobile" in the body of the message
> 



To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message