Re: CF card & pcmcia adapter issues
Eric Masson <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
>>>>> "Bruce" == Bruce M Simpson <Bruce> writes: Bruce> In order to get various flavours of CF to work I used the Bruce> following:- <snip pccard.conf entries> I'll have a look asap. Bruce> Enclose a 'pccard dumpcis' and we may be able to help further, Bruce> but try tailoring one of those regexps to suit your card's CIS. Attached. Regards Eric Masson -- > C'est malheureux de constater k'apres kelkes millers d'années d'evolution, > les hommes sont encore au stade *primitive* : peur de ce k'on ne connait > pas, juger ses sembles a tout prix, coller une etiquette et j'en passe. -+- Gl in : <http://www.le-gnu.net> - fufe, c'est du Darwin -+-
dumpcis.txt
(application/octet-stream, 4.6 KB)
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: d9 01 ff
Common memory device information:
Device number 1, type Function specific, WPS = ON
Speed = 250nS, Memory block size = 2Kb, 1 units
Tuple #2, code = 0x1c (Other conditions for common memory), length = 4
000: 03 d9 01 ff
(MWAIT) (3V card)
Tuple #3, code = 0x18 (JEDEC descr for common memory), length = 2
000: df 01
Tuple #4, code = 0x20 (Manufacturer ID), length = 4
000: 01 4e 00 02
PCMCIA ID = 0x4e01, OEM ID = 0x200
Tuple #5, code = 0x15 (Version 1 info), length = 43
000: 04 01 44 45 4d 20 41 54 41 20 46 6c 61 73 68 20
010: 20 20 20 20 20 20 20 20 20 20 20 00 53 54 4f 52
020: 4d 20 20 00 53 54 4c 30 31 00 ff
Version = 4.1, Manuf = [DEM ATA Flash ], card vers = [STORM ]
Addit. info = [STL01]
Tuple #6, code = 0x21 (Functional ID), length = 2
000: 04 01
Fixed disk card - POST initialize
Tuple #7, code = 0x22 (Functional EXT), length = 2
000: 01 01
Disk interface: IDE
Tuple #8, code = 0x22 (Functional EXT), length = 3
000: 02 04 5f
Disk features: Silicon, Single
Sleep, Standby, Idle, Low power, Reg inhibit, Iois16
Tuple #9, code = 0x1a (Configuration map), length = 5
000: 01 03 00 02 0f
Reg len = 2, config register addr = 0x200, last config = 0x3
Registers: XXXX----
Tuple #10, code = 0x1b (Configuration entry), length = 11
000: c0 40 a1 27 55 4d 5d 75 08 00 21
Config index = 0x0(default)
Interface byte = 0x40 (memory) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Max current average over 10 ms: 8 x 10mA
Memory space length = 0x8
Max twin cards = 1
Misc attr: (Power down supported)
Tuple #11, code = 0x1b (Configuration entry), length = 6
000: 00 01 21 b5 1e 4d
Config index = 0x0
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 10 ms: 4.5 x 10mA
Tuple #12, code = 0x1b (Configuration entry), length = 13
000: c1 41 99 27 55 4d 5d 75 64 f0 ff ff 21
Config index = 0x1(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Max current average over 10 ms: 8 x 10mA
Card decodes 4 address lines, full 8/16 Bit I/O
IRQ modes: Level, Pulse, Shared
IRQs: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Max twin cards = 1
Misc attr: (Power down supported)
Tuple #13, code = 0x1b (Configuration entry), length = 6
000: 01 01 21 b5 1e 4d
Config index = 0x1
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 10 ms: 4.5 x 10mA
Tuple #14, code = 0x1b (Configuration entry), length = 18
000: c2 41 99 27 55 4d 5d 75 ea 61 f0 01 07 f6 03 01
010: ee 21
Config index = 0x2(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Max current average over 10 ms: 8 x 10mA
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x1f0 block length = 0x8
I/O address # 2: block start = 0x3f6 block length = 0x2
IRQ modes: Level, Pulse, Shared
IRQ level = 14
Max twin cards = 1
Misc attr: (Power down supported)
Tuple #15, code = 0x1b (Configuration entry), length = 6
000: 02 01 21 b5 1e 4d
Config index = 0x2
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 10 ms: 4.5 x 10mA
Tuple #16, code = 0x1b (Configuration entry), length = 18
000: c3 41 99 27 55 4d 5d 75 ea 61 70 01 07 76 03 01
010: ee 21
Config index = 0x3(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Max current average over 10 ms: 8 x 10mA
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x170 block length = 0x8
I/O address # 2: block start = 0x376 block length = 0x2
IRQ modes: Level, Pulse, Shared
IRQ level = 14
Max twin cards = 1
Misc attr: (Power down supported)
Tuple #17, code = 0x1b (Configuration entry), length = 6
000: 03 01 21 b5 1e 4d
Config index = 0x3
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 10 ms: 4.5 x 10mA
Tuple #18, code = 0x14 (No link), length = 0
Tuple #19, code = 0xff (Terminator), length = 0