Re: LinkSys wpc11v2.5 card: random shutdown?
Larry Rosenman <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
* M. Warner Losh <[email protected]> [020405 01:59]: > In message: <[email protected]> > Larry Rosenman <[email protected]> writes: > : * M. Warner Losh <[email protected]> [020405 01:29]: > : > In message: <[email protected]> > : > Larry Rosenman <[email protected]> writes: > > Hmmm. I hate it when that happens. I'm using a similar card right > now, but it isn't the exact linksys card that you have. > > What does pccardc dumpcis before/after this event tell you? What does > 'pccardc power 1 0' followed by a 'pccardc power 1 1' do for you? Here is the pccardc dumpcis when it's working: Configuration data for card in slot 1 Tuple #1, code = 0x1 (Common memory descriptor), length = 3 000: 00 00 ff Common memory device information: Device number 1, type No device, WPS = OFF Speed = No speed, Memory block size = 512b, 1 units Tuple #2, code = 0x17 (Attribute memory descriptor), length = 4 000: 67 5a 08 ff Attribute memory device information: Device number 1, type SRAM, WPS = OFF Speed = 5.0 x 100 ns, Memory block size = 512b, 2 units Tuple #3, code = 0x1d (Other conditions for attribute memory), length = 5 000: 03 67 5a 08 ff (MWAIT) (3V card) Tuple #4, code = 0x15 (Version 1 info), length = 75 000: 01 00 54 68 65 20 4c 69 6e 6b 73 79 73 20 47 72 010: 6f 75 70 2c 20 49 6e 63 2e 00 49 6e 73 74 61 6e 020: 74 20 57 69 72 65 6c 65 73 73 20 4e 65 74 77 6f 030: 72 6b 20 50 43 20 43 61 72 64 00 49 53 4c 33 37 040: 33 30 30 50 00 52 65 76 41 00 ff Version = 1.0, Manuf = [The Linksys Group, Inc.], card vers = [Instant Wireless Network PC Card] Addit. info = [ISL37300P],[RevA] Tuple #5, code = 0x20 (Manufacturer ID), length = 4 000: 74 02 12 16 PCMCIA ID = 0x274, OEM ID = 0x1612 Tuple #6, code = 0x21 (Functional ID), length = 2 000: 06 00 Network/LAN adapter Tuple #7, code = 0x22 (Functional EXT), length = 2 000: 01 07 Network technology: Wireless Tuple #8, code = 0x22 (Functional EXT), length = 5 000: 02 40 42 0f 00 Network speed: 1 Mb/sec Tuple #9, code = 0x22 (Functional EXT), length = 5 000: 02 80 84 1e 00 Network speed: 2 Mb/sec Tuple #10, code = 0x22 (Functional EXT), length = 5 000: 02 60 ec 53 00 Network speed: 5 Mb/sec Tuple #11, code = 0x22 (Functional EXT), length = 5 000: 02 c0 d8 a7 00 Network speed: 11 Mb/sec Tuple #12, code = 0x22 (Functional EXT), length = 2 000: 03 07 Network media: 2.4 GHz Tuple #13, code = 0x22 (Functional EXT), length = 8 000: 04 06 00 02 dd 31 3f c2 Network node ID: 00 02 dd 31 3f c2 Tuple #14, code = 0x22 (Functional EXT), length = 2 000: 05 01 Network connector: closed connector standard Tuple #15, code = 0x1a (Configuration map), length = 7 000: 03 01 e0 03 00 00 01 Reg len = 4, config register addr = 0x3e0, last config = 0x1 Registers: X------- Tuple #16, code = 0x1b (Configuration entry), length = 14 000: c1 01 19 76 35 d5 19 36 36 05 46 ff ff ff Config index = 0x1(default) Interface byte = 0x1 (I/O) Vcc pwr: Minimum operating supply voltage: 3 x 1V Maximum operating supply voltage: 5 x 1V, ext = 0x19 Max current average over 1 second: 3 x 100mA Max current average over 10 ms: 3 x 100mA Power down supply current: 1 x 10mA Card decodes 6 address lines, limited 8/16 Bit I/O IRQ modes: Level, Pulse, Shared IRQs: NMI IOCK BERR VEND 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Tuple #17, code = 0xff (Terminator), length = 0 2 slots found I generally can't do ANY commands when it powers off, because the machine locks up until I pop the card. As soon as I pop the card, the machine frees up, and if I wait for the beeps, and re-insert the card, it's back in business (usually :-) ). LER -- Larry Rosenman http://www.lerctr.org/~ler Phone: +1 972-414-9812 E-Mail: [email protected] US Mail: 1905 Steamboat Springs Drive, Garland, TX 75044-6749 To Unsubscribe: send mail to [email protected] with "unsubscribe freebsd-mobile" in the body of the message