USB wierdness on Vaio

Oliver Enzmann <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile
Message-ID <[email protected]> 
Hi,

External USB devices on my Sony VAIO R600 laptop disable the USB port
under 5.0-CURRENT (cvsup'ed on the 26th):

    Nov 28 17:19:34 vaio kernel: usb_new_device: set address 2 failed
    Nov 28 17:19:34 vaio kernel: uhub_explore: usb_new_device failed,
    error=SET_ADDR_FAILED
    Nov 28 17:19:34 vaio kernel: uhub0: device problem, disabling port 1

However, this laptop also has a built-in (USB) Sony Memorystick reader
that works just fine. Also, the two USB devices I am testing with work
just fine with 5.0-DP2 on an old Dell laptop. The USB devices are:

    Iomega USB CDRW9602EXT-B
    Y-E DATA USB Floppy Drive

On the Vaio, USB port status changes from - to

1.  port 1 powered
2.  port 1 addr 0 should never happen!
3.  port 1 addr 2: full speed, power 100 mA, unconfigured, product \
     0x0055(0x0055), Iomega(0x059b), rev 11.00
4.  port 1 enabled

usbdevs -v and Dmesg below.

Your help is greatly appreciated, Oliver

---------------------------------------------------------------

usbdevs -v:

Controller /dev/usb0:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), 
Intel(0x0000), rev 1.00
  port 1 powered
  port 2 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), 
Intel(0x0000), rev 1.00
  port 1 addr 2: full speed, self powered, config 1, USB Memory Stick 
Slot(0x0056), Sony(0x054c), rev 1.80
  port 2 powered

---------------------------------------------------------------

dmesg:


FreeBSD 5.0-CURRENT #1: Thu Nov 28 16:55:29 CET 2002
     [email protected]:/usr/src/sys/i386/compile/VAIOMAX
Preloaded elf kernel "/boot/vaiomax/kernel" at 0xc0482000.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 844610161 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (844.61-MHz 686-class CPU)
   Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
 
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 132644864 (126 MB)
avail memory = 123904000 (118 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
acpi0: <SONY   U1      > on motherboard
Using $PIR table, 9 entries at 0xc00fdf30
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.LNKA irq   9: [  9] low,level,sharable 0.1.0
\\_SB_.LNKB irq   9: [  9] low,level,sharable 0.1.1
\\_SB_.LNKC irq   0: [  9] low,level,sharable 0.1.2
\\_SB_.LNKD irq   0: [  9] low,level,sharable 0.1.3
\\_SB_.LNKA irq   9: [  9] low,level,sharable 0.2.0
\\_SB_.LNKB irq   9: [  9] low,level,sharable 0.31.1
\\_SB_.LNKH irq   9: [  9] low,level,sharable 0.31.2
\\_SB_.LNKD irq   0: [  9] low,level,sharable 0.31.3
---- before setting priority for links ------------
\\_SB_.LNKC:
         interrupts:          9
         penalty:           830
         references:     1
         priority:       0
\\_SB_.LNKD:
         interrupts:          9
         penalty:           830
         references:     2
         priority:       0
---- before fixup boot-disabled links -------------
\\_SB_.LNKD:
         interrupts:          9
         penalty:           830
         references:     2
         priority:       1660
\\_SB_.LNKC:
         interrupts:          9
         penalty:           830
         references:     1
         priority:       830
---- after fixup boot-disabled links --------------
\\_SB_.LNKD:
         interrupts:          9
         penalty:           830
         references:     2
         priority:       1660
\\_SB_.LNKC:
         interrupts:          9
         penalty:           830
         references:     1
         priority:       830
---- arbitrated configuration ---------------------
\\_SB_.LNKA irq   9: [  9] low,level,sharable 0.1.0
\\_SB_.LNKB irq   9: [  9] low,level,sharable 0.1.1
\\_SB_.LNKC irq   0: [  9] low,level,sharable 0.1.2
\\_SB_.LNKD irq   0: [  9] low,level,sharable 0.1.3
\\_SB_.LNKA irq   9: [  9] low,level,sharable 0.2.0
\\_SB_.LNKB irq   9: [  9] low,level,sharable 0.31.1
\\_SB_.LNKH irq   9: [  9] low,level,sharable 0.31.2
\\_SB_.LNKD irq   0: [  9] low,level,sharable 0.31.3
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem 
0xf4000000-0xf407ffff,0xf8000000-0xfbffffff irq 9 at device 2.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
---- initial configuration ------------------------
\\_SB_.LNKA irq   9: [  9] low,level,sharable 1.0.0
\\_SB_.LNKC irq   0: [  9] low,level,sharable 1.2.0
\\_SB_.LNKD irq   0: [  9] low,level,sharable 1.2.1
\\_SB_.LNKE irq   9: [  9] low,level,sharable 1.8.0
\\_SB_.LNKA irq   9: [  9] low,level,sharable 1.12.0
\\_SB_.LNKB irq   9: [  9] low,level,sharable 1.12.1
\\_SB_.LNKC irq   0: [  9] low,level,sharable 1.12.2
\\_SB_.LNKD irq   0: [  9] low,level,sharable 1.12.3
---- before setting priority for links ------------
\\_SB_.LNKD:
         interrupts:          9
         penalty:          1670
         references:     4
         priority:       1660
\\_SB_.LNKC:
         interrupts:          9
         penalty:          1670
         references:     3
         priority:       830
---- before fixup boot-disabled links -------------
\\_SB_.LNKD:
         interrupts:          9
         penalty:          1670
         references:     4
         priority:       6680
\\_SB_.LNKC:
         interrupts:          9
         penalty:          1670
         references:     3
         priority:       5010
---- after fixup boot-disabled links --------------
\\_SB_.LNKD:
         interrupts:          9
         penalty:          1670
         references:     4
         priority:       6680
\\_SB_.LNKC:
         interrupts:          9
         penalty:          1670
         references:     3
         priority:       5010
---- arbitrated configuration ---------------------
\\_SB_.LNKA irq   9: [  9] low,level,sharable 1.0.0
\\_SB_.LNKC irq   0: [  9] low,level,sharable 1.2.0
\\_SB_.LNKD irq   0: [  9] low,level,sharable 1.2.1
\\_SB_.LNKE irq   9: [  9] low,level,sharable 1.8.0
\\_SB_.LNKA irq   9: [  9] low,level,sharable 1.12.0
\\_SB_.LNKB irq   9: [  9] low,level,sharable 1.12.1
\\_SB_.LNKC irq   0: [  9] low,level,sharable 1.12.2
\\_SB_.LNKD irq   0: [  9] low,level,sharable 1.12.3
pci1: <ACPI PCI bus> on pcib1
fwohci0: <Texas Instruments TSB43AA22> mem 
0xf4104000-0xf4107fff,0xf4101000-0xf41017ff irq 9 at device 0.0 on pci1
fwohci0: PCI bus latency was changing to 250.
cache size 8.
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: resetting OHCI...done (0)
fwohci0: BUS_OPT 0xa002 -> 0xf800a002
fwohci0: Link 1394a available S400, 2 ports, maxrec 2048 bytes.
fwohci0: Enable 1394a Enhancements
fwohci0: EUI64 08:00:46:03:00:c3:9a:d3
fwochi_set_intr: 1
firewire0: <IEEE1394(Firewire) bus> on fwohci0
firewire0: firewire bus attach
sbp_identify
sbp_probe
sbp0: <SBP2/SCSI over firewire> on firewire0
sbp_attach
cbb0: <RF5C475 PCI-CardBus Bridge> at device 2.0 on pci1
start (88000000) < sc->membase (f4100000)
end (ffffffff) > sc->memlimit (f41fffff)
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib1: possible interrupts:  9
pcib1: slot 2 INTA routed to irq 9 via \\_SB_.LNKC
fxp0: <Intel Pro/100 Ethernet> port 0x3000-0x303f mem 0xf4100000-0xf4100fff 
irq 9 at device 8.0 on pci1
fxp0: Ethernet address 08:00:46:17:51:ab
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0x1800-0x180f at device 31.1 on 
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0x1820-0x183f 
irq 9 at device 31.2 on pci0
uhci0: LegSup = 0x00001f20
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0x2400-0x241f 
irq 9 at device 31.4 on pci0
uhci1: LegSup = 0x00002f00
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
umass0: Sony USB Memory Stick Slot, rev 1.10/1.80, addr 2
umass0: 8070i (ATAPI) over CBI with CCI (using CBI); quirks = 0x0000
umass0:1:0:-1: Attached to scbus1 as device 0
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pmtimer0 on isa0
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xd8000-0xdbfff,0xc0000-0xcbfff 
on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
spic0: device model type = 2
spic0: <Sony Programmable I/O Controller> at port 0x10a0-0x10a4 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
firewire0: BUS reset
firewire0: node_id = 0xc000ffc0, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fw_set_bus_manager: 63->0 (loop=0)
send phy_config root_node=-1 gap_count=1
start AT DMA status=0
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
start (88000000) < sc->membase (f4100000)
end (ffffffff) > sc->memlimit (f41fffff)
start (88000000) < sc->membase (f4100000)
end (ffffffff) > sc->memlimit (f41fffff)
wi0: <Instant Wireless Network PC Card> at port 0x100-0x13f irq 9 function 0 
config 1 on pccard0
wi0: 802.11 address: xx:yy:xx:yy:xx:yy
wi0: using RF:PRISM2.5 MAC:ISL3873
wi0: Intersil Firmware: Primary 1.00.07, Station 1.03.05
bus_explore done
ad0: 19077MB <HITACHI_DK23BA-20> [38760/16/63] at ata0-master UDMA66
(probe7:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe7:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe7:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe7:umass-sim0:0:0:0): UNIT ATTENTION asc:28,0
(probe7:umass-sim0:0:0:0): Not ready to ready change, medium may have changed
(probe7:umass-sim0:0:0:0): Retrying Command (per Sense Data)


To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.