Re: DP2 + Thinkpad 660X = PC Card card activation failed

Bob Van Valzah <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile,gmane.os.freebsd.current
Message-ID <1038796195.375.7.camel@OutBound> 
On Sat, 2002-11-30 at 23:16, M. Warner Losh wrote:
> Try adding hw.pccard.cis_debug=1 to /boot/loader.conf and let me know
> the results.

Warner, I knew you'd know what to try next!

Here's what's new in dmesg apparently as a result of the cis_debug flag
(full dmesg output follows the signature):

cis mem map d1b00000
pccard0: CIS tuple chain:
CISTPL_END
ff
cis mem map d1b00000
CISTPL_LINKTARGET expected, code ff observed

It looks to me like a null tuple chain was found where a link target was
expected.  But I have no clue how to interpret this in context.

All advice appreciated!

	Bob

Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-DP2 #1: Sat Nov 16 13:38:33 GMT 2002
[email protected]:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0679000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06790a8.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 498274185 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (498.27-MHz 686-class CPU)
Origin = "GenuineIntel"  Id = 0x681  Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 268238848 (255 MB)
avail memory = 253636608 (241 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <IBM    TP600X  > on motherboard
Using $PIR table, 6 entries at 0xc00f9d70
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe"  frequency 3579545 Hz
ACPI-0351: *** Error: Could not install PciConfig handler for PCI0, AE_ALREADY_EXISTS
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xef08-0xef0b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_tz1: <thermal zone> on acpi0
acpi_tz2: <thermal zone> on acpi0
acpi_tz3: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\_SB_.LNKD irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.3
\_SB_.LNKA irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.2.0
\_SB_.LNKB irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.2.1
\_SB_.LNKC irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.3.0
\_SB_.LNKB irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.5.0
\_SB_.LNKA irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.6.0
---- before setting priority for links ------------
\_SB_.LNKD:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1660  1660   660  1660  1660   660   660   660  1660 10660 10660
references:	1
priority:	0
\_SB_.LNKA:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1660  1660   660  1660  1660   660   660   660  1660 10660 10660
references:	2
priority:	0
\_SB_.LNKB:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1660  1660   660  1660  1660   660   660   660  1660 10660 10660
references:	2
priority:	0
\_SB_.LNKC:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1660  1660   660  1660  1660   660   660   660  1660 10660 10660
references:	1
priority:	0
---- before fixup boot-disabled links -------------
\_SB_.LNKA:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1660  1660   660  1660  1660   660   660   660  1660 10660 10660
references:	2
priority:	5865
\_SB_.LNKB:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1660  1660   660  1660  1660   660   660   660  1660 10660 10660
references:	2
priority:	5865
\_SB_.LNKD:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1660  1660   660  1660  1660   660   660   660  1660 10660 10660
references:	1
priority:	2932
\_SB_.LNKC:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1660  1660   660  1660  1660   660   660   660  1660 10660 10660
references:	1
priority:	2932
---- after fixup boot-disabled links --------------
\_SB_.LNKA:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   660   660   660   660  1660  1660  1660  1660  1660 10660 10660
references:	2
priority:	5865
\_SB_.LNKB:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   660   660   660   660  1660  1660  1660  1660  1660 10660 10660
references:	2
priority:	5865
\_SB_.LNKD:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   660   660   660   660  1660  1660  1660  1660  1660 10660 10660
references:	1
priority:	2932
\_SB_.LNKC:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   660   660   660   660  1660  1660  1660  1660  1660 10660 10660
references:	1
priority:	2932
---- arbitrated configuration ---------------------
\_SB_.LNKD irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.7.3
\_SB_.LNKA irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.2.0
\_SB_.LNKB irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.2.1
\_SB_.LNKC irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.3.0
\_SB_.LNKB irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.5.0
\_SB_.LNKA irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 0.6.0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0x40000000-0x43ffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
---- initial configuration ------------------------
\_SB_.LNKA irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 1.0.0
\_SB_.LNKB irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 1.0.1
---- before setting priority for links ------------
\_SB_.LNKA:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1880  1880   880  1880  1880   880   880   880  1880 10880 10880
references:	3
priority:	5865
\_SB_.LNKB:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1880  1880   880  1880  1880   880   880   880  1880 10880 10880
references:	3
priority:	5865
\_SB_.LNKD:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   880   880   880   880  1880  1880  1880  1880  1880 10880 10880
references:	1
priority:	2932
\_SB_.LNKC:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   880   880   880   880  1880  1880  1880  1880  1880 10880 10880
references:	1
priority:	2932
---- before fixup boot-disabled links -------------
\_SB_.LNKA:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1880  1880   880  1880  1880   880   880   880  1880 10880 10880
references:	3
priority:	9458
\_SB_.LNKB:
interrupts:	     3     4     5     6     7     9    10    11    12    14    15
penalty:	  1880  1880   880  1880  1880   880   880   880  1880 10880 10880
references:	3
priority:	9458
\_SB_.LNKD:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   880   880   880   880  1880  1880  1880  1880  1880 10880 10880
references:	1
priority:	3152
\_SB_.LNKC:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   880   880   880   880  1880  1880  1880  1880  1880 10880 10880
references:	1
priority:	3152
---- after fixup boot-disabled links --------------
\_SB_.LNKA:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   880   880   880   880  1880  1880  1880  1880  1880 10880 10880
references:	3
priority:	9458
\_SB_.LNKB:
interrupts:	    11    10     9     5    12     7     6     4     3    15    14
penalty:	   880   880   880   880  1880  1880  1880  1880  1880 10880 10880
references:	3
priority:	9458
\_SB_.LNKD:
interrupts:	     5     9    10    11     3     4     6     7    12    14    15
penalty:	   880   880   880   880  1880  1880  1880  1880  1880 10880 10880
references:	1
priority:	3152
\_SB_.LNKC:
interrupts:	     5     9    10    11     3     4     6     7    12    14    15
penalty:	   880   880   880   880  1880  1880  1880  1880  1880 10880 10880
references:	1
priority:	3152
---- arbitrated configuration ---------------------
\_SB_.LNKA irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 1.0.0
\_SB_.LNKB irq   0: [  3  4  5  6  7  9 10 11 12 14 15] low,level,sharable 1.0.1
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1450 PCI-CardBus Bridge> mem 0x50103000-0x50103fff irq 11 at device 2.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <TI1450 PCI-CardBus Bridge> mem 0x50102000-0x50102fff irq 11 at device 2.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pci0: <simple comms> at device 3.0 (no driver attached)
pci0: <multimedia, audio> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfcf0-0xfcff at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x4000-0x401f irq 11 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x3bc-0x3c3 irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
cis mem map d1b00000
pccard0: CIS tuple chain:
CISTPL_END
ff
cis mem map d1b00000
CISTPL_LINKTARGET expected, code ff observed
pccard0: Card has no functions!
cbb0: PC Card card activation failed
ad0: 11509MB <IBM-DARA-212000> [24944/15/63] at ata0-master UDMA33
Mounting root from ufs:/dev/ad0s1a


To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.