FreeBSD Installation on HP Pavilion ZT1130

Eduardo Maestri Righes <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile
Message-ID <[email protected]> 
Hi,

I'm trying to install the FreeBSD 4.7-RELEASE on my HP Pavilion ZT1130
notebook, but there is some problems.

Note: my notebook doesn't have floppy drive.

When a try to boot from my CD drive (actually a Toshiba DVD-ROM SD-R2102
drive), I got the following message:

BTX loader 1.00 BTX version is 1.01
Console: internal video/keyboard
BIOS drive C: is disk0
BIOS 639kB/244672kB available memory

FreeBSD/i386 bootstrap loader, Version 0.8
...
Can't work out which disk we are booting from.
Guessed BIOS device 0x0 not found by probes, defaulting to disk0:
...
Can't load 'kernel'
Can't load 'kernel.old'

I search for any information through search engines on the Internet,
but I can't find anything.

Below, there is some information about my machine.

Thanks in advance and sorry about the long message.

[]'s Eduardo

---//---

HP Pavilion ZT1130 PCI devices (the following info is an output form
lspci -vv from my Slackware Linux installation):

00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at a0000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
		Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=x4
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP] (prog-if
00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000c000-0000dfff
	Memory behind bridge: e0000000-efffffff
	Prefetchable memory behind bridge: 90000000-9fffffff
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.0 CardBus bridge: ENE Technology Inc: Unknown device 1410
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=64
	I/O window 0: 00000000-00000003
	I/O window 1: 00000000-00000003
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
	16-bit legacy interface ports at 0001

00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C (rev 10)
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at e200 [size=256]
	Region 1: Memory at f0000000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 Communication controller: ESS Technology ES2838/2839 SuperLink
Modem (rev 01)
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at e300 [size=16]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=55mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable+ DSel=0 DScale=0 PME-

00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge]
(rev 10)
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Region 4: I/O ports at 1100 [size=16]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1e) (prog-if 00
[UHCI])
	Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 64, cache line size 08
	Interrupt: pin D routed to IRQ 10
	Region 4: I/O ports at 1200 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 1e) (prog-if 00
[UHCI])
	Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 64, cache line size 08
	Interrupt: pin D routed to IRQ 10
	Region 4: I/O ports at 1300 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10)
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Capabilities: [68] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686
AC97 Audio Controller (rev 40)
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin C routed to IRQ 9
	Region 0: I/O ports at e000 [size=256]
	Region 1: I/O ports at e100 [size=4]
	Region 2: I/O ports at e104 [size=4]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: S3 Inc. VT8603 [ProSavage PN133]
AGP4X VGA Controller (Twister) (rev 02) (prog-if 00 [VGA])
	Subsystem: Hewlett-Packard Company: Unknown device 0020
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (1000ns min, 63750ns max), cache line size 04
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=512K]
	Region 1: Memory at 90000000 (32-bit, prefetchable) [size=128M]
	Expansion ROM at 000c0000 [disabled] [size=64K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] AGP version 2.0
		Status: RQ=31 SBA- 64bit- FW- Rate=x4
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=x4


My current disk partitioning:


Disk /dev/hda: 255 heads, 63 sectors, 2432 cylinders
Units = cylinders of 16065 * 512 bytes

     Device Boot    Start       End    Blocks   Id  System
/dev/hda1             2         7     48195   84  OS/2 hidden C: drive
/dev/hda2   *         8      1024   8169052+   7  HPFS/NTFS
/dev/hda3          1025      1285   2096482+   c  Win95 FAT32 (LBA)
/dev/hda4          1286      2432   9213277+   5  Extended
/dev/hda5          1286      1318    265041   82  Linux swap
/dev/hda6          1319      2147   6658911   83  Linux
/dev/hda7          2148      2432   2289231   83  Linux


/proc/ioports from Slackware Linux 8.1


0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vesafb
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1100-110f : VIA Technologies, Inc. Bus Master IDE
    1100-1107 : ide0
    1108-110f : ide1
1200-121f : VIA Technologies, Inc. UHCI USB
1300-131f : VIA Technologies, Inc. UHCI USB (#2)
c000-dfff : PCI Bus #01
e000-e0ff : VIA Technologies, Inc. AC97 Audio Controller
    e000-e0ff : via82cxxx_audio
e100-e103 : VIA Technologies, Inc. AC97 Audio Controller
    e100-e103 : via82cxxx_audio
e104-e107 : VIA Technologies, Inc. AC97 Audio Controller
    e104-e107 : via82cxxx_audio
e200-e2ff : Realtek Semiconductor Co., Ltd. RTL-8139
    e200-e2ff : 8139too
e300-e30f : ESS Technology ES2838/2839 SuperLink Modem


/proc/interrupts from Slackware Linux 8.1


             CPU0
    0:       9244          XT-PIC  timer
    1:        276          XT-PIC  keyboard
    2:          0          XT-PIC  cascade
    8:          1          XT-PIC  rtc
    9:          0          XT-PIC  via82cxxx
   10:          0          XT-PIC  eth0
   12:         21          XT-PIC  PS/2 Mouse
   14:       2462          XT-PIC  ide0
   15:          9          XT-PIC  ide1
NMI:          0
ERR:          0

-- 
[]'s Eduardo

Eduardo Maestri Righes <[email protected]>



To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-questions" in the body of the message





To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.