Re: 4.7 -> 5.0 Pccard problems (more info)

On Fri, Dec 27, 2002 at 06:33:57AM -0800, Pat Lathem wrote:

> I am running 5.0 current from a few days ago. I upgrade fairly often 
> hoping that it will be fixed.
> 
> When I booted with the -v flag, everything proceeded normally until I 
> attempted to power up the slot the card was in (pccardc power 0 1) . The 
> first two lines are shown to the console, and then the third line is 
> printed repeatedly:
> pcic0: reset 1 int is 0 stat is 0
> pcic0: reset 2 int is 0 stat is 0
> pcic0: reset 3 int is 0 stat is 0  (<-- this one is then repeated in a 
> loop until the slot is powered down)
> 
> Does anyone know what this means?

I guess Warner Losh could help here if he has enough time to look at this.

> 
> After I power it down (pccardc power 0 0):
> pcic0: reset 0
> 
> Here is the output from dmesg (I am still using OLDCARD)
> 
> [trashcan]~: dmesg | grep pcic0
> pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 6.0 on pci2
> pcic0: PCI Memory allocated: 0xd0200000
> pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr 
> save][CSC serial isa irq]
> pccard0: <PC Card 16-bit bus (classic)> on pcic0
> 
> [trashcan]~: dmesg | grep pci2
> pci2: <ACPI PCI bus> on pcib2
> pci2: <simple comms> at device 4.0 (no driver attached)
> pci2: <serial bus, FireWire> at device 5.0 (no driver attached)
> pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 6.0 on pci2
> fxp0: <Intel Pro/100 Ethernet> port 0x3040-0x307f mem 
> 0xd0215000-0xd0215fff irq 10 at device 8.0 on pci2
> 
> 
> Pat Lathem
> 
> Kirill Bezzubets wrote:
> 
> >On Thu, Dec 26, 2002 at 06:21:10AM -0800, Pat Lathem wrote:
> >
> > 
> >
> >>>>cbb0: <TI1410 PCI-CardBus Bridge> irq 11 at device 6.0 on pci2
> >>>>cardbus0: <CardBus bus> on cbb0
> >>>>pccard0: <16-bit PCCard bus> on cbb0
> >>>> 
> >>>>       
> >>>>
> >>The card is a supported IBM 56k modem (I also have been expirementing 
> >>with a Linksys wireless card). The kernel does not say anything when I 
> >>insert or remove it (with GENERIC), which is why I assumed it was not 
> >>being detected properly. Since I posted the, I have reverted to the 
> >>kernel OLDCARD. After the computer boots, I can run 'pccardc power 0 1' 
> >>and it starts to initialize the card, but fails to read the correct 
> >>vendor string from the pccard. I'm currently changing the hints file (at 
> >>the advice of Greg Smith) to see if it can work. My question is this: Is 
> >>this is a regression? In 4.7-stable I only had to add to /etc/rc.conf 
> >>"pccard_enable="YES"'  and reboot (or start pccardd) to get my cards 
> >>working. Was I just lucky that it just worked the first time, or is 
> >>there a problem?
> >>   
> >>
> >
> >One more thing from your dmesg output (sorry, just noticed..):
> >
> >cbb0: Unsupported card type detected
> >
> >I guess it's a kind of bug with TI1410 (???), not sure though.
> >Because mine is TI1131 PCI-CardBus Bridge and everything works well
> >with both 16bit(PCCard) and 32bit(CardBus) cards using NEWCARD.
> >Also it did work in 4-STABLE since 4.3 with PCCards.
> >

--
BR,
Kirill Bezzubets                                CASE-RIPE CASE-RIPN
Senior Administrator, Technical Department      mailto:[email protected]
Solaris ISP & Telecommunications Co. Ltd        http://www.solaris.ru

To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message